Harbor Breeze ECHOLAKE 00876 User manual

1
Español p. 19
ECHOLAKE CEILING FAN
ITEM #0747603, 0747604
MODEL #00876, 00877
Serial Number Purchase Date
Harbor Breeze ® is a registered trademark of LF,
LLC. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday
8 a.m. - 5 p.m., EST Friday
EB15554
ATTACH YOUR RECEIPT HERE
UL MODEL #52-GV
Lowes.com/harborbreeze Lowes.com/harborbreeze
COVER - Page 1
Page 12

3
2
TABLE OF CONTENTS
Safety Information............................................................................................................... 2
Package Contents............................................................................................................... 4
Hardware Contents...............................................................................................................5
Preparation ......................................................................................................................... 5
Assembly or Installation Instructions .................................................................................. 6
Operating Instructions ........................................................................................................ 16
Care and Maintenance ....................................................................................................... 17
Troubleshooting...................................................................................................................17
Warranty..............................................................................................................................18
Replacement Parts List ...................................................................................................... 18
SAFETY INFORMATION
WARNING
CAUTION
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or
install the product.
• When using an existing outlet box, be sure the box is securely attached to the building structure
and can support the full weight of the fan, so to avoid potential serious injury or death.
• All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local
 electricalcodes.Electricalinstallationshouldbeperformedbyaqualiedlicensedelectrician.
• DONOTusebulbswithwattagegreaterthanthemaximumvaluestatedonthextureandin
 thismanual.Usingahigherwattagebulbthanspeciedwillincreasexturetemperatureand
 causeriskofre.
• Disconnect the electrical supply circuit to the fan before installing kit.
• Electrical diagrams are for reference only.
• The net weight of this fan including the light kit is: 21.38 lbs.
• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, do not use this fan with any
solid-state speed control device.
• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, make sure the electricity
has been turned off at the circuit breaker or fuse box before beginning installation.
• PERSONAL INJURY HAZARD - To reduce the risk of injury to persons, install fan so that the
 bladesare7ft.abovetheoor.
• ELECTRIC SHOCK HAZARD - Do not install this fan with variable speed wall control or wall-
mounted dimmer switch. It will permanently damage the fan’s remote control receiver and cause
the fan’s functions to fail.
ON
ON / OFF switch NO Variable speed wall control NO Dimmer switch
• FIRE,ELECTRICSHOCKORPERSONALINJURYHAZARD-Toreducetheriskofre,
electric shock, or personal injury, mount to an outlet box marked “ACCEPTABLE FOR FAN
SUPPORT OF 35.1 lbs OR LESS” and use the mounting screws provided with the outlet box.
Mostoutletboxescommonlyusedforthesupportoflightingxturesarenotacceptableforfan
supportandmayneedtobereplaced.Consultaqualiedlicensedelectricianifindoubt.
• PERSONAL INJURY HAZARD - To reduce the risk of personal injury, do not bend the blade
brackets when installing the brackets, balancing the blades, or cleaning the fan. DO NOT insert
foreign objects in between the rotating fan blades.
Lowes.com/harborbreeze Lowes.com/harborbreeze
Page 3
Page 2

A 1
B 1
C 1
D 1
E 1
F 5
G 5
H 1
I 3
J 1
K 2
L 1
M 1
54
HARDWARE CONTENTS (shown actual size)
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 45 minutes.
Tools Required for Assembly (not included): Phillips screwdriver, step ladder, electrical tape, pliers,
wire cutters, wire strippers.
Helpful Tools (not included): Electrical Circuit tester.
PACKAGE CONTENTS
AMounting Bracket (preassembled to canopy (B))
Canopy
Canopy Cover (preassembled to canopy (B))
Yoke Cover
Downrod Assembly
Blade Bracket
Blade
Motor Housing
Light Kit
Glass Bowl
Bulb
Bowl Cap (preassembled to light kit (I))
Finial (preassembled to light kit (I))
PART DESCRIPTION QUANTITY
K
K
F
A
I
H
G
D
C
B
EJ
L
M
M
AA BB CC DD
EE FF
Fan Pull Chain
Extension
Qty. 1
(NOT TO SCALE)
Light Pull Chain
Extension
Qty. 1
(NOT TO SCALE)
Wire Connector
Qty. 4
Blade Screw
Qty. 16
Plug
Qty. 1
Blade Bracket
Screw
Qty. 10
GG
Rubber Gasket
Qty. 1
(NOT TO SCALE)
Lowes.com/harborbreeze Lowes.com/harborbreeze
Page 4 Page 5

6 7
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
1. Determine mounting method to use.
A - Downrod Mount (normal or angled ceiling)
B - Closemount (normal ceiling only)
Important: lf using the angle mount, check to
make sure the ceiling angle is not steeper than 20°.
4. Install the mounting bracket (A) to the outlet box
(not included) using the two screws provided
with the outlet box. Securely tighten the two
screws.
2.Removeanddiscardtheverubberinsertsand
vemountingscrewsfromtheundersideof
the motor housing (H).
2. Insert downrod assembly (E) through canopy
(B), canopy cover (C) and yoke cover (D).
Thread wires from the motor housing (H)
through downrod assembly (E).
Outlet box
A
4
3. Remove the mounting bracket (A) from the canopy
(B) by loosening the four screws on the top of the
canopy (B). Remove the two non-slotted screws and
save.
1
A
B
A
B
Remove
and save
Loosen but
do not remove
3
If using the angle mount, make sure open end of
mounting bracket (A) is installed facing the ceiling.
Follow mounting instructions for Downrod Style
Fan Mounting on page 7 or Closemount Style
Fan Mounting on page 8, depending on mounting
method (A or B) chosen in step 1 on page 6.
DOWNROD STYLE FAN MOUNTING
1. Remove pin and clip from downrod assembly
(E) and save.
2
C
B
D
E
HRubber
insert
and screw
21
Clip
Pin
E
Lowes.com/harborbreeze Lowes.com/harborbreeze
Page 6 Page 7

8 9
DOWNROD STYLE FAN MOUNTING CLOSEMOUNT STYLE FAN MOUNTING
3. Loosen the two set screws from the yoke. Slip
downrod assembly (E) into yoke, aligning holes
in downrod assembly (E) and yoke. Insert the
pin through yoke and downrod assembly (E),
then insert clip into pin until it snaps into place.
Tighten set screws. Slide the yoke cover (D)
down over the motor housing (H).
2. Remove every other screw from the top of the
motor housing (H) and save.
4. Install hanger ball on the top of downrod assembly
(E) into mounting bracket (A) opening. Rotate fan
until slot on hanger ball engages the tab on the
mounting bracket (A).
3. Place the rubber gasket (FF) over the remaining
screws on motor housing (H). Pull wires through
hole in canopy (B), and attach canopy (B)
to motor housing (H) using the three screws
removed in previous step. Tighten the screws
securely.
1. Remove the canopy cover (C) from the bottom
of the canopy (B).
4. Temporarily hang the canopy (B) onto the hook
on the mounting bracket (A) using one of the
non-slotted holes in the canopy (B). This will
allow for hands-free wiring.
2
1
DANGER: Be careful when aligning the tab
to the slot! If not fully engaged, there is a
possibility of fan falling, which may result in
serious injury or death.
You may now proceed to WIRING page 10.
B
C
CLOSEMOUNT STYLE FAN MOUNTING
H
Hardware Used
FF Rubber gasket x 1
3
Clip
Pin
Set screw
Yoke
E
D
H
4
B
A
Hook
HB
FF
4
Tab
Slot
A
E
3
HB
FF
Lowes.com/harborbreeze Lowes.com/harborbreeze
Page 8 Page 9

10
WIRING
Hardware Used
1. Connect the BLACK and BLUE wires from the
fan to the house BLACK wire. Connect the
WHITE wire from fan to the house WHITE wire.
Connect all GROUNDED (GREEN) wires together
from fan to the house GREEN/GROUND wire.
Note: BLACK wire is hot power for fan. BLUE
wire is hot power for light kit in case of future light
kit installation. WHITE wire is common for fan
and light kit. GREEN wire is ground wire. If house
wires are different colors than referred to above,
stop immediately. Consult a licensed electrician to
determine proper wiring.
2. To connect wires, twist wire ends together and
screw wire with wire connectors (AA) in a clockwise
direction. Tape the wire connectors (AA) and wires
together with electrical tape (not included). Be sure
no bare wire or wire strands are visible after making
connection.
Place GREEN and WHITE connections on opposite
side of box from the BLACK and BLUE connections.
The splices should be turned upward and pushed
carefully up into the outlet box.
1
2
x 4
Wire Connector
AA
Page 10 Page 11
FINAL INSTALLATION
You may now proceed to Step 4.
3. Directly align the locking slots of the canopy (B) with
the two screws previously loosened (step 3, page 6)
in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock in place. Immediately
tightenthetwoscrewsrmly,thenre-installthetwo
screws that were previously removed (step 3, page 6)
to fully secure the canopy (B) to the mounting bracket
(A).
4. Attach blade (G) to a blade bracket (F) using three
blade screws (DD).
Repeat for remaining blade assemblies.
11
2. Re-install the two screws that were previously removed
(step 3, page 6) to fully secure the canopy (B) to the
mounting bracket (A).
Ground/Green
Black
White
Ground/
Green
Black
Blue
White
Supply circuit
Speed switch
Outlet box
blue
black
white
green white
GREEN/
GROUND
black
AA
FINAL INSTALLATION
If you installed the fan with “Closemount Style Fan
Mounting”, continue to Steps 1 and 2. If you installed
the fan with “Downrod Style Fan Mounting”, skip to
Step 3.
1Outlet
box Screws
hook
Locking
slots B
A
1. Remove the fan from the hook on the mounting
bracket (A). Align the locking slots of the canopy
(B) with the two screws previously loosened (step
3, page 6) in the mounting bracket (A). Push up to
engage the slots and turn clockwise to lock in place.
Immediatelytightenthetwoscrewsrmly.
2Screw
Outlet box
B
3
B
Screw
Outlet box
DD Blade Screw x 16
Hardware Used
G
DD
F
THIS SIDE UP
4
Lowes.com/harborbreeze Lowes.com/harborbreeze

7 H
White
Black
Blue
I
12 13
FINAL INSTALLATION
5. Align the post of blade bracket (F) to the slot on
the bottom of the motor housing (H). Secure blade
bracket (F) using blade bracket screws (EE).
NOTE: The switch cup has an access hole that
is sealed with a waterproof rubber plug. Remove
the rubber plug to allow the screwdriver to reach
the screws in the blade bracket. Position the blade
bracket on the motor and tighten by inserting the
screwdriver through the access hole. Once all blade
brackets have been attached, replace the rubber
plug in the access hole.
Repeat this step for the remaining blade assemblies.
8. Attach light kit (I) to the bottom of the motor
housing (H) by aligning the holes in each part and
re-installing the previously removed screws (Step
6, page 12). Tighten securely.
9. Install bulbs (K) into sockets in light kit (I).
Note: This fan has an energy-saving wattage limiter
included. If candelabra-base bulbs are more than
190 watts, light will automatically turn off. Please
ensure bulb wattage is always less than 190 watts.
10.Removethepreassemblednial(M)andbowlcap
(L) from the light kit (I).
FINAL INSTALLATION
6
Screw
I
10
I
M
L
9H
K
I
8
I
Screw
H
7. Connect the adapter plug of the BLUE wire from the
fan motor assembly (H) to the adapter plug of the
BLACK wire from the light kit (I) and connect the
adapter plug of the WHITE wire from the fan motor
assembly (H) to the adapter plug of the WHITE wire
from the light kit (I).
6. To install the fan WITH the light, remove and
save the three preassembled screw from the
switch of light kit (I).
NOTE: To install this fan WITH the light kit, continue
to step 6. To install the fan WITHOUT the light kit,
proceed to step 13.
EE Blade Bracket Screw x 16
Hardware Used
HB
FF
5
F
H
EE
Waterproof
rubber plug
Lowes.com/harborbreeze Lowes.com/harborbreeze
Page 12

14 15
Hardware Used
11. Place glass (J) on the preassembled pipe on light kit
(I)untilitisushwiththepreassembledmetaldisk.
Securewithpreviouslyremovedbowlcap(L)andnial
(M). Tighten securely.
12. Attach fan pull chain extension (BB) and light pull
chain extension (CC).
11
I
J
LM
BB
CC
12
I
Hex Nut
Washer
Switch
housing
cover
13
I
GG
Switch
housing
cover
I
Screw
H
BB
H
Fan pull chain
14
15
16
13. To install the fan WITHOUT the light, remove the
hex nut and washer preassembled inside the switch
housing cover of the light kit (I) and detach the
switch housing cover.
14. Place the plug (GG) into the center hole of the
switch housing cover.
15. Remove and save the three preassembled screws
from the switch housing cover. Attach switch housing
cover to the bottom of the motor housing (H) by
aligning the holes in each part and re-installing the
previously removed screws. Tighten securely.
16. Attach fan pull chain extension (BB).
FINAL INSTALLATION FINAL INSTALLATION
Assembly is now complete.
Light pull chain extensions
x
BB
CC
1
x 1
Fan pull chain extensions
Lowes.com/harborbreeze Lowes.com/harborbreeze

1. PULL CHAIN:
2. REVERSE SWITCH:
When the season changes, you may want to change
the direction your fan spins. To switch between
clockwiseandcounterclockwiserotations,ipthefan
reversal switch.
WARNING: Wait for fan to stop before reversing the
switch.
A. In cooler weather, clockwise rotation creates an
upwardairow,whichmoveshotairfromthe
ceiling into the room. Push the switch RIGHT.
B. In warmer weather, counterclockwise rotation
createsadownwardairow,whichcoolstheair.
Push the switch LEFT.
• The fan pull chain is for motor speed control:
High, Medium, Low and Off. Pull chain once for
each position.
• Thelightpullchaincontrolsthelightxtureeither
ON or OFF with each pull of the chain.
OPERATING INSTRUCTIONS
Reverse
switch
Fan pull
chain Light pull
chain
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fan does not move. 1. Chain switch is “off”.
2. Faulty wire connection.
3. Reverse switch not engaged.
1. Pull chain switch.
2. Turn power off. Loosen canopy,
check all connections.
3. Pushswitchrmlyeitherway.
Noisy operation. 1. Blades are loose.
2. Cracked blade.
3. Unapproved speed control.
1. Tighten all blade screws.
2. Replace blades (call customer
service).
3. Replace with an approved speed
control device.
Excessive wobbling. 1. The blades are loose.
2. Blade brackets incorrectly
attached.
3. Unbalanced blades.
4. The fan is not securely mounted.
5. Fan too close to vaulted ceiling.
1. Tighten all blade screws.
2. Reinstall blade brackets.
3. Switch with blade from the
opposite side.
4. Turn power off. Carefully loosen
the canopy and remount securely.
5. Lower fan or move it to another
location.
TROUBLESHOOTING
CARE AND MAINTENANCE
• Important: Shut off main power supply before beginning any maintenance.
• Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly
dampened cloth will be suitable for most cleaning.
• Cleanfanhousingwithonlyasoftbrushorlint-freeclothtoavoidscratchingthenish.Clean
blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to blades
for added protection.
• At least twice a year, tighten all screws and lower canopy to check mounting bracket screws and
downrod assembly.
17
16
Lowes.com/harborbreeze Lowes.com/harborbreeze

18
PART DESCRIPTION PART #
Item #0747603 Item #0747604
EDownrod Assembly 102200-0210UB 102200-0210ZW
F Blade Bracket 104000-0346UB 104000-0346ZW
G Blade 108003-304579 108003-3045ZW
WARRANTY
REPLACEMENT PARTS LIST
The manufacturer warrants this fan to be free from defects in workmanship and material present at
time of shipment from the factory for lifetime limited from the date of purchase. This warranty applies
only to the original purchaser. The manufacturer agrees to correct such defect at no charge or at our
option replace the ceiling fan with a comparable or superior model.
To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of
removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the
ceilingfanbyaccident,misuse,orimproperinstallation,orbyafxingaccessoriesnotproducedby
the manufacturer of the fan, are at the purchaser’s own responsibility. The manufacturer assumes
no responsibility whatsoever for fan installation during the lifetime limited warranty. Any service
performed by an unauthorized person will render the warranty invalid.
Duetovaryingclimaticconditions,thiswarrantydoesnotcoverchangesinbrassnish,rusting,
pitting,tarnishing,corroding,orpeeling.Brassnishfansmaintaintheirbeautywhenprotectedfrom
varying weather conditions. Any glass provided with this fan is not covered by this warranty. Any
replacementofdefectivepartsfortheceilingfanmustbereportedwithintherstyearfromthedate
of purchase. For the balance of the warranty, call our customer service department at 1-800-643-0067
for return authorization and shipping instructions so that we may repair or replace the ceiling fan.
Any fan or parts returned improperly packaged is the sole responsibility of the purchaser. There is no
further expressed warranty. The manufacturer disclaims any and all implied warranties.
The duration of any implied warranty which can not be disclaimed is limited to the lifetime limited
periodasspeciedinourwarranty.Themanufacturershallnotbeliableforincidental,consequential
or special damages arising at or in connection with product use or performance except as may
otherwisebeaccordedbylaw.Thiswarrantygivesyouspeciclegalrightsanyoualsohaveother
rights which may vary from state to state. This warranty supersedes all prior warranties.
Note: A small amount of “wobble” is normal and should not be considered a defect.
Printed in China
For replacement parts, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST,
Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
F
A
G
E
Lowes.com/harborbreeze
Harbor Breeze ® is a registered
trademark of LF, LLC. All Rights
Reserved.