Mitsubishi Electric LGH-100RX3-CAN User manual

TECHNICAL MANUAL FOR CANADA
Models Lossnay Unit
LGH-50RX3-CAN
LGH-100RX3-CAN
LGH-200RX3-CAN
Lossnay Remote Controller
PZ-41SLB-E
PZ-52SF-E

i
CONTENTS
Lossnay Unit
CHAPTER 1 Ventilation for Healthy Living
1. Necessity of Ventilation ...................................................................................................................................... 2
2. Ventilation Standards .......................................................................................................................................... 4
3. Ventilation Method .............................................................................................................................................. 5
4. Ventilation Performance ...................................................................................................................................... 8
5. Outdoor Air (ventilation) Load .............................................................................................................................. 10
CHAPTER 2 Lossnay Construction and Principle
1. Construction and Features of Lossnay .............................................................................................................. 16
2. Construction and Principle of Core ...................................................................................................................... 16
3. Calculation of the Total Heat Recovery Efficiency .............................................................................................. 18
4. What is a Psychrometric Chart? ........................................................................................................................ 19
5. Calculation of Lossnay Heat Recovery .............................................................................................................. 20
CHAPTER 3 General Technical Considerations
1. Lossnay Heat Recovery Effect ............................................................................................................................ 22
2. Example Heat Recovery Calculation .................................................................................................................. 24
3. Calculation of Lossnay Economical Effects ........................................................................................................ 26
4. Psychrometric Chart .......................................................................................................................................... 28
5. The Result of No Bacterial Cross Contamination for the Lossnay Core and Determining
Resistance of the Lossnay Core to Molds .......................................................................................................... 29
6. Flame-proofing Properties of Lossnay Core ...................................................................................................... 31
7. Lossnay Core’s Soundproofing Properties Test .................................................................................................. 33
8. Change in Lossnay Core Over Time .................................................................................................................. 34
9. Comparison of Heat Recovery Techniques ........................................................................................................ 36
CHAPTER 4 Characteristics
1. How to Read the Characteristic Curves .............................................................................................................. 40
2. Calculating the Static Pressure Loss .................................................................................................................. 40
3. How to Obtain Efficiency from Characteristic Curves ........................................................................................ 44
4. Sound .................................................................................................................................................................. 45
5. NC Curves .......................................................................................................................................................... 51
6. List of Models ...................................................................................................................................................... 52
CHAPTER 5 System Design Recommendations
1. Lossnay Usage Conditions ................................................................................................................................ 58
2. Noise Value of Lossnay with Built-in Fans .......................................................................................................... 59
3. Attachment of Air Filter ...................................................................................................................................... 59
4. Duct Construction .............................................................................................................................................. 59
5. By-pass Ventilation ............................................................................................................................................ 59
6. Transmission Rate of Various Gases and Related Maximum Workplace Concentration .................................. 60
7. Solubility of Odors and Toxic Gases, etc., in Water and Effect on Lossnay Core .............................................. 61
8. Automatic Ventilation Switching .......................................................................................................................... 62
9. Vertical Installation .............................................................................................................................................. 63
10. Installation of Supplementary Fan Devices After Lossnay Unit .......................................................................... 64

ii
CHAPTER 6 Examples of Lossnay Applications
1. Large Office Building .......................................................................................................................................... 66
2. Medium Size Office Building .............................................................................................................................. 69
3. Urban Small-Scale Building ................................................................................................................................ 73
4. Hospitals ............................................................................................................................................................ 74
5. Schools .............................................................................................................................................................. 76
6. Public Halls (combination facilities such as day-care centres) .......................................................................... 78
CHAPTER 7 Installation Considerations .................................................................................................... 82
CHAPTER 8 Filtering for Freshness
1. Necessity of Filters .............................................................................................................................................. 86
2. Data Regarding Dust .......................................................................................................................................... 86
3. Calculation Table for Dust Collection Efficiency of Each Lossnay Filter ............................................................ 87
4. Comparison of Dust Collection Efficiency Measurement Methods .................................................................... 89
5. Calculation of Dust Concentration ...................................................................................................................... 91
CHAPTER 9 Service Life and Maintenance
1. Service Life ........................................................................................................................................................ 94
2. Cleaning the Lossnay Core and Pre-filter .......................................................................................................... 94
CHAPTER 10 Ventilation Standards in Each Country
1. Ventilation Standards in Each Country ................................................................................................................ 96
2. U.S. ...................................................................................................................................................................... 97
3. U.K. ...................................................................................................................................................................... 97
CHAPTER 11 Lossnay Q and A .......................................................................................................................... 100
Lossnay Remote Controller
1. Summary ................................................................................................................................................................ 107
2. Applicable Models ................................................................................................................................................ 107
3. Terminology ............................................................................................................................................................ 108
4. System Features and Examples ...................................................................................................................... 109
5. Examples of Applications Using External Control Input Terminals,
Operation Monitor Output Terminals and Malfunction Monitor Output Terminals ................................ 127
6. Precautions When Designing Systems of M-NET ........................................................................................ 134
7. Cable Installation of the M-NET ........................................................................................................................ 137
8. System Designs of M-NET ................................................................................................................................ 140
9. Automatic Ventilation Switching ........................................................................................................................ 142
10. Cold Weather Area Operation Specifications ................................................................................................ 143
11.Troubleshooting .................................................................................................................................................... 145
12. Installation method .............................................................................................................................................. 159
13. Lossnay Remote Controller (PZ-41SLB-E) .................................................................................................... 170
14. Lossnay M-NET Remote Controller (PZ-52SF-E) ........................................................................................ 176
15. Appendix ................................................................................................................................................................ 181
*Centralised Controller (MJ-103MTRA) .......................................................................................... 181
*Remote Controllers for Mr. Slim indoor unit ................................................................................................ 188
*Network Remote Controller (PAR-F27MEA) ................................................................................................ 191

CHAPTER 1
Ventilation for Healthy Living
Lossnay Unit

2
CHAPTER 1 ●Ventilation for Healthy Living
Fresh outdoor air must be introduced constantly at a set ratio in an air conditioning system. This fresh air is introduced to be
mixed with the return air from the room, to adjust the temperature and humidity, supply oxygen, reduce body and other odors,
remove tobacco smoke and to increase the cleanness of the air.
The standard ventilation (outdoor air intake) volume is determined according to the type of application, estimated number of
persons in the room, room area, and relevant regulations. Systems which accurately facilitate these requirements are
increasingly being required to be installed in buildings.
1. Necessity of Ventilation
The purpose of ventilation is basically divided into “oxygen supply”, “cleaning of air”, “temperature control” and “humidity
control”. Cleaning of the air includes the elimination of “odors”, “gases”, “dust” and “bacteria”. The needs of ventilation are
divided into “personal comfort”, “assurance of environment for animals and plants”, and “assurance of environments for
machinery and constructed materials”.
In Japan legal regulations regarding ventilation are set in the Building Srandard Law Enforcement Ordinance and the “Building
Management Law” for securing a sanitary environment in buildings. These are in general agreeance with similar regulations in
other countries.
1.1 Room air environment in buildings
In Japan, the Building Management Law, a law concerning the sanitary environment of buildings, designates eleven
applications including offices, shops, and schools with a total floor area of 3,000 m2or more, as buildings. According to this
law maintenance and management of the ventilation and water supply and discharge according to the Environmental
Sanitation Management Standards is obligatory.
The following table gives a specific account of buildings in Tokyo.
(Tokyo Food and Environment Guidance Center Report)
Specific Account of Buildings in Tokyo (March, 2003)
Number of buildings %
Offices 1,467 56.7
Shops 309 22.0
Department Stores 63 2.4
Schools 418 16.2
Inns 123 4.8
Theaters 86 3.3
Libraries 12 0.5
Museums 11 0.4
Assembly Halls 63 2.4
Art Museums 8 0.3
Amusement Centers 27 1.0
Total 2,587 100.0
Note: Excludes buildings with an expanded floor space of 3,000 to 5,000 m2in particular areas.
The ratio of results of the air quality measurement public
inspection and the standard values that were not met (percentage
of unsuitability) for the approximately 500 buildings examined in
1980 is shown in the chart at the right.
There was a large decrease in unsuitable percentages of floating
particles, but there was almost no change in temperature and
carbon dioxide. Values for temperature, ventilation, and carbon
monoxide almost entirely cleared the standard values, and are
excluded. The study from 1989 shows the item with the highest
percentage of unsuitability as temperature with 37%, followed by
carbon dioxide at 15%.
76 77 78 79 80 8171 72 73 74 75 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
70
60
50
40
30
20
10
0

relative humidity
carbon dioxide
temperature
carbon monoxide
ventilation
floating particles
Percentage of unsuitability (%)
Percentage of unsiutability of air quality by year
(according to the Tokyo Food and Environment Guidance Center)

3
CHAPTER 1 ●Ventilation for Healthy Living
Effect of carbon monoxide (CO) 10,000 ppm = 1%
Concentration (ppm) Effect of concentration changes
0.01 - 0.2 Standard atmosphere.
5Considered to be the long-term tolerable value.
10 The Building Standard Law of Japan, Law for Maintenance of Sanitation in Buildings.
Environmental standard 24-hour average.
20 Considered to be the short-term tolerable value.
Environmental standard 8-hour average.
50 Tolerable concentration for labor environment.
(Japan Industrial Sanitation Association)
100 No effect for 3 hours. Effect noticed after 6 hours.
Headache, illness after 9 hours; harmful for long-term but not fatal.
200 Light headache in the forehead in 2 to 3 hours.
400 Headache in the forehead, nausea in 1 to 2 hours; headache in the back of head in 2.5 to 3 hours.
800 Headache, dizziness, nausea, convulsions in 45 minutes. Comatose in 2 hours.
1,600 Headache, dizziness in 20 minutes. Death in 2 hours.
3,200 Headache, dizziness in 5 to 10 minutes. Death in 30 minutes.
6,400 Death in 10 to 15 minutes.
12,800 Death in 1 to 3 minutes.
Several 10,000 ppm This level may be found in automobile exhaust.
(Several %)
Apprpx. 5 ppm is
an annual
average value in
city areas.
This value may
exceed 100 ppm
near roads, in
tunnels and
parking areas.
Concentration (%) Standards and effect of concentration changes
Approx. 21 Standard atmosphere.
20.5 Ventilation air volume standard will be a guideline where concentration does not decrease more than 0.5%
from normal value. (The Building Standard Law of Japan)
20 - 19 An oxygen deficiency of this amount does not directly endanger life in a normal air pressure, but if there is a
combustion device in the area, the generation of CO will increase rapidly due to incomplete combustion.
18 Industrial Safety and Health Act. (Hypoxia prevention regulations.)
16 Normal concentration in exhaled air.
16 - 12 Increase in pulse and breathing resulting in dizziness and headaches.
15 Flame in combustion devices will extinguish.
12 Threat to life in short term.
7Fatal
In the case of Japan, an Instruction Guideline based on these regulations has been issued, and unified guidance is carried out.
Part of the Instruction Guideline regarding ventilation is shown below.
●The fresh outdoor air intake must be 10 m or higher from ground level, and be distanced appropriately from the exhaust air
outlet. (Neighbouring buildings must also be considered.)
●The fresh outdoor air intake volume must be 25 to 30 m3/h·person in design.
●An air volume measurement hole must be installed at an effective position to measure the treated air volume of the
ventilating device.
●The position and shape of the supply diffuser and return grille must be selected so the air environment in the room is
distributed evenly.
1.2 Effect of air contamination on human bodies
Effect of oxygen (O2) concentration

4
CHAPTER 1 ●Ventilation for Healthy Living
Effect of carbon dioxide (CO2)
Note: According to Facility Check List published by Kagekuni-sha.
1.3 Effect of air contamination in buildings
●Dirtiness of interior
New ceilings, walls and ornaments will turn yellow in one to two years. This is caused by dust and the tar in tobacco smoke.
2. Ventilation Standards
The legal standards for ventilation differ according to each country. Please follow the standards set by the country. In the US,
Ashrae revised their standards in 1989 becoming more strict.
In Japan, regulations are set in the The Building Standard Law of Japan Enforcement Ordinance, the so-called “Building
Management Law” for securing a sanitary environment in buildings. According to the Building Standards Law, a minimum of
20 m3/h per person of ventilation air is required.
Concentration (%) Effect of concentration changes
0.03 (0.04) Standard atmosphere.
0.04 - 0.06 City air.
0.07 Tolerable concentration when many people stay for long time.
0.10 General tolerable concentration.
The Building Standard Law of Japan, Law for Maintenance of Sanitation in Buildings.
0.15 Tolerable concentration used for ventilation calculations.
0.2 - 0.5 Observed as relatively poor.
0.5 or more Observed as the poorest.
0.5 Long-term safety limits (U.S. Labor Sanitation) ACGIH, regulation of laborer offices.
2Depth of breathing and inhalation volume increases 30%.
3Work and physical functions deteriorate, breathing doubles.
4Normal exhalation concentration.
4 - 5 The respiratory center is stimulated; depth and times of breathing increases. Dangerous if breathed in for a
long period. If an O2deficiency also occurs, trouble will occur sooner and be more dangerous.
8When breathed in for 10 minutes, breathing difficulties, redness in the face and headaches will occur.
The trouble will worsen when there is also a deficiency of O2.
18 or more Fatal
There is no toxic level in
CO2alone.
However, these tolerable
concentrations are a
guideline of the
contamination estimated
when the physical and
chemical properties of
the air deteriorate in
proportion to the increase
of CO2.

5
CHAPTER 1 ●Ventilation for Healthy Living
3. Ventilation Method
3.1 Ventilation class and selection points
An appropriate ventilation method must be selected according to the purpose.
Ventilation is composed of “Supply air” and “Exhaust air” functions. These functions are classified according to natural flow or
mechanical ventilation using a fan (forced ventilation).
Classification of mechanical ventilation
Classification of ventilation (according to Building Standards Law)
1. Class 1 ventilation
Fresh outdoor air is mechanically
brought in and simultaneously the
stale air in the room is mechanically
discharged.
2. Class 2 ventilation
Fresh outdoor air is mechanically
brought in and the exhaust air is
discharged from the exhaust air
outlet (natural).
3. Class 3 ventilation
The stale air in the room is
mechanically discharged and
simultaneously fresh outdoor air is
mechanically introduced from the
supply air diffuser (natural).
Ex. of application
•Ventilation of air
conditioned rooms.
(buildings, hospitals,
etc.)
•Ventilation of room
not facing an outer
wall. (basement,
etc.)
•Ventilation of large
room. (office, large
conference room,
hall, etc.)
•Surgery theatre.
•Clean rooms.
•Foodstuff processing
factories.
•Local ventilation in
kitchens.
•Ventilation of hot
exhaust air from
machine room, etc.
•Ventilation of humid
exhaust air from
indoor pools, bath-
rooms, etc.
•General simple
ventilation.
System effect
By changing the
balance of the supply
fan and exhaust fan’s
air volumes, the
pressure in the room
can be balanced
freely, and the
interrelation with
neighboring spaces
can be set freely.
As the room is
pressurized, the flow
of odors and dust,
etc., from neighboring
areas can be
prevented.
The exhaust air is
removed from a local
position in the room,
and dispersion of the
stale air can be
prevented by applying
an entire negative
pressure.
Design and construction
properties
• An ideal design in which
the supply air diffuser
and exhaust air outlet
position relation and air
volume, etc., can be set
freely is possible.
•Asystem which adjusts
the temperature and
humidity of the supply
air diffuser flow to the
room environment can
be incorporated.
•
The supply and
exhaust volume can be
set freely according to
the changes in
conditions.
•The position and
shape of the supply
air diffuser can be
set.
•The temperature and
humidity of the
supply air diffuser
flow can be set
accordingly, and
dust can be removed
as required.
•Effective exhausting
of dispersed stale air
generation sites is
possible from a local
exhaust air outlet.
•Ventilation in which
the air flow is not felt
is possible with the
supply air diffuser
setting method.
Selection points
•Accurate supply air
diffuser can be
maintained.
•The room pressure
balance can be
maintained.
•The supply air
diffuser temperature
and humidity can be
adjusted and dust
treatment is
possible.
•The pressure is
positive.
•
The supply air diffuser
temperature and
humidity can be
adjusted, and dust
treatment is possible.
• The positional relation
of the exhaust air
outlet to the supply air
diffuser is important.
•The room pressure
is negative.
•Local exhaust is
possible.
•Ventilation without
dispersing stale air is
possible.
•Ventilation with
reduced air flow is
possible.
•
The positional relation
of the exhaust air
outlet to the supply air
diffuser is important.
Supply
air
diffuser
Exhaust
fan
Exhaust
air
outlet
Exhaust
fan
Exhaust
fan
Stale
air
Fresh
outdoor
air
Supply Exhaust Ventilation volume Room pressure
Class 1 Mechanical Mechanical Random (constant) Random
Class 2 Mechanical Natural Random (constant) Positive pressure
Class 3 Natural Mechanical Random (constant) Negative pressure
Class 4 Natural Mechanical & natural Limited (inconstant) Negative pressure

1) System operation with cassette-type air conditioner
2) System operation with ceiling embedded-type air conditioner
3) Independent operation with ceiling suspended-type air conditioner
6
CHAPTER 1 ●Ventilation for Healthy Living
3.2 Comparison of ventilation methods
There are two main types of ventilation methods.
Centralized ventilation method
This is mainly used in large buildings, with the fresh outdoor air intake being installed in one machine room. For this method,
primary treatment of the fresh outdoor air, such as heat recovery to the intake air and dust removal is performed being
distribution to the building by ducts.
Independent zoned ventilation method
This is mainly used in small to medium sized buildings, with areas being ventilated using fresh outdoor air intakes formed of
independent ventilation devices. The rate of use of this method has recently increased as independent control is becoming
ever more feasible.
Centralised ventilation method Independent zoned ventilation method
Air intake
(fresh out-
door air) Filters
Air exhaust
(stale air)
Cassette-type package air
conditioner or fan coil unit
Cassette-type or ceiling suspended-type
package air conditioner or fan coil unit
Ceiling-mounted type Lossnay or
ceiling embedded-type Lossnay
Exhaust grill
Ceiling recessed-
type Lossnay
Exhaust air
Fresh outdoor air
Finished ceiling
Fresh outdoor air
Exhaust air
Finished ceiling
Lossnay
Supply fan
Exhaust
Each unit
Ceiling embedded-type package
air conditioner or fan coil unit
Ceiling recessed-
type Lossnay
Exhaust grill
Exhaust air
Fresh outdoor air
Finished ceiling

7
CHAPTER 1 ●Ventilation for Healthy Living
Comparison of centralised ventilation method and independent zoned ventilation method
Centralized ventilation method
The air transfer distance is long thus requiring
much fan power.
•Independent equipment room is required.
•Duct space is required.
•Penetration of floors with vertical shaft is not
desired in terms of fire prevention.
Generalized per system.
•Design of outer wall is not lost.
•The indoor supply air diffuser and return grille
can be selected freely for an appropriate design.
As there are many common-use areas, if the
building is a tenant building, an accurate
assessment of operating cost is difficult.
•As the usage time setting and ventilation volume
control, etc., is performed in a central monitoring
room, the user’s needs may not be met
appropriately.
•Alarge amount of ventilation is required even
for a few persons.
•An ideal supply air diffuser and return grille
position can be selected as the supply air
diffuser and return grilles can be laid out freely.
•The only noise in the room is the aerodynamic
sound.
•Anti-vibration measures must be taken as the
fan in the equipment room is large.
•Centralized management is easy as it can be
performed in the equipment room.
•The equipment can be inspected at any time.
•Large as the entire system is affected.
•Immediate inspection can be performed in the
equipment room.
Fan power
Installation space
Zoning
Designability
Clarification of costs
Controllability
Comfort
Maintenance and
management
Trouble correspondence
Independent zoned ventilation method
As the air transfer distance is short, the fan power
is small.
•Independent equipment room is not required.
•Piping space is required only above the ceiling.
Can be utilised for any one area.
•The number of intakes and exhaust air outlets
on the outer wall will increase; design must be
considered.
•The design will be fixed due to the installation
fittings, so the design of the intakes and exhaust
air outlets must be considered.
Invoicing for each zone separately is possible,
even in a tenant building.
•The user in each zone can operate the ventilator
freely.
•The ventilator can be operated even during off-
peak hours.
•Consideration must be made of the noise from
the main unit.
•Anti-vibration measures are often not required
as the unit is compact and the vibration
generated can be dispersed.
•Work efficiency is poor as the equipment is not
centrally located.
•An individual unit can be inspected only when
the room it serves is vacant.
•Limited as only independent units are affected.
•Consultation with the tenant is required prior to
inspection of an individual unit.

8
CHAPTER 1 ●Ventilation for Healthy Living
4. Ventilation Performance
The ventilation performance is largely affected by the installation conditions. Ample performance may not be achieved unless
the model and usage methods are selected according to the conditions.
Generally, the ventilation performance is expressed by “Air volume” and “wind pressure (static pressure)”, and these are
necessary when considering ventilation.
4.1 Air volume
Air volume expresses the volume of air exhausted (or supplied) by the unit in a given period. Generally, this is expressed as
m3/hr (hour).
4.2 Wind pressure
When a piece of paper is placed in front of a fan and let go, the piece of paper will be blown away. The force that blows the
paper away is called the wind pressure, and this is normally expressed in units of Pa. The wind pressure is divided into the
following three types:
4.2.1 Static pressure
This is the force that presses the surroundings when the air is still such as in an automobile tyre or rubber balloon. For
example, in a water gun, the hydraulic pressure increases when pressed by a piston, and if there is a small hole, the water
sprays out with force. The pressure of this water is equivalent to the static pressure for air. The higher the pressure is, the
further the water (air) can be sprayed.
4.2.2 Dynamic pressure
This expresses the speed at which air flows, and can be thought of as the force at which a typhoon presses against a building.
4.2.3 Total pressure
This is the total force that wind has, and is the sum of the static pressure and dynamic pressure.

9
CHAPTER 1 ●Ventilation for Healthy Living
4.3 Measurement of the air volume and wind pressure
Mitsubishi measures the machine’s air volume and wind pressure with a device as shown below according to the Japan
Industrial Standards (JIS B 8628).
Measuring device using orifice (JIS B 8628 standards)
Static pressure (H)
Air volume (Q)
Measurement method
The unit is operated with the throttle device fully closed. There is no air flow at this time, and the air volume is 0. The maximum
point of the static pressure (A point, the static pressure at this point is called the totally closed pressure) can be obtained. Next,
the throttle device is gradually opened, the auxiliary fan is operated, and the middle points (points B, C and D) are obtained.
Finally, the throttle device is completely opened, and the auxiliary fan is operated until the static pressure in the chamber
reaches 0. The maximum point of the air volume (point E, the air volume at this point is called the fully opened air volume) is
obtained. The points are connected as shown below, and are expressed as air volume, static pressure curves (Q-H curve).
Connection
Wind dispersing place
Connection
Rectifying
grid
Rectifying
grid
Supply
Air
(SA)
Chamber
Return
Air
(RA)
Rectifying
net
Rectifying
net
Wind gauge
duct path Orifice
Wind gauge
duct path Orifice
Damper
Blower
Blower
Test unit
Test unit
Static pressure in chamber
(Static pressure measurement)
Static pressure in chamber
(Static pressure measurement)
Pressure
difference before
and after orifice
(Air volume
measurement)
A) When measuring the supply air volume (with the orifice plate)
B) When measuring the return air volume (with the orifice plate)

10
CHAPTER 1 ●Ventilation for Healthy Living
5. Outdoor Air (ventilation) Load
5.1 How to calculate each approximate load
The outdoor air load can be calculated with the following formula if the required outside air intake volume Q m3/h to be
introduced is known:
(Outdoor air load) = γ· QF· (iO- iR)
= γ[kg/m3] ×S[m2] ×k ×n [person/m2] ×Vf [m3/h·person] ×(iO- iR): ∆i [kJ/kg]
γ:Specific gravity of air - 1.2 kg/m3
S:Building’s airconditioned area
k:Thermal coefficient; generally 0.7 - 0.8.
n:The average population concentration is the inverse of the occupancy area per person. If the number of persons in the
room is unclear, refer to the Floor space per person table below.
Vf : Outdoor air intake volume per person
Refer to the Required outdoor air intake volume per person table below.
iO:Outdoor air enthalpy - kJ/kg
iR:Indoor enthalpy - kJ/kg
Floor space per person table (m2)
(According to the Japan Federation of Architects and Building Engineers Associations)
Required outdoor air intake volume per person table (m3/h·person)
Caution
The application of this table to each type of room should be carefully considered in relation to the degree of smoking in
the room.
Office building Department store, shop Restaurant Teatre or
Average Crowded Empty cinema hall
General design 4 - 7 0.5 - 2 0.5 - 2 5 - 8 1 - 2 0.4 - 0.6
value 53.0 1.0 6.0 1.5 0.5
Application example Required ventilation volume
Degree of smoking Recommended value Minimum value
Broker’s office
Extremely heavy Newspaper editing room 85 51
Conference room
Quite heavy Bar 51 42.5
Cabaret
Heavy Office 25.5 17
Restaurant 20
Light Shop 25.5 17
Department store
None Theatre 25.5 17
Hospital room 34 25.5

Cooling load per unit area
When the volume of outdoor air per person is 25 m3/h, and the number of persons per 1 m2is 0.2, the cooling load will be
approximately 157.0 W/m2.
How these values are determined can be seen as follows:
●Outdoor air load
Air conditions <Standard design air conditions in Tokyo>
11
CHAPTER 1 ●Ventilation for Healthy Living
Example calculations of determining ventilation load during both cooling and heating are given as follows:
5.2 Ventilation load during cooling (in general office building)
●Classification of cooling load
(a) is the heat infiltrating the room, and often is 30 to 40% of the entire cooling load.
(b) is the heat generated in the room.
(c) is applies only when reheating is necessary.
(d) is the heat generated when outdoor air is mixed into part of the supply air diffuser volume and introduced into the room.
The outdoor air is introduced to provide ventilation for the people in the room, and is referred to as the ventilating load.
Typical load values (during cooling)
Type of load Load
Outdoor air load 53.0 W/m2
Indoor People 26.4 W/m2
generated heat Lighting equipment 30.0 W/m2
Indoor infiltration heat 47.6 W/m2
Total 157.0 W/m2
Conditions: Middle floor of a general office building facing south.
Class
Heat from walls (qWS)
(a) Indoor infiltration heat Heat from glass from direct sunlight (qGS)
from conduction & convection (qGS)
Accumulated heat load in walls (qSS)
Generated heat from people Sensible heat (qHS)
(b) Indoor generated heat Latent heat (qHL)
Genarated heat from electrical equipment Sensible heat (qES)
Latent heat (qEL)
(c) Reheating load (qRL)
(d) Outdoor air load Sensible heat (qFS)
Latent heat (qFL)
}
}
}
}
When the load per floor area of 1 m2with a ventilation volume of 25 m3/h·person is calculated with the above air conditions,
the following is obtained:
Outdoor air (ventilation) load = 1.2 kg/m3(Specific gravity of air) ×0.2 persons/m2(no. of persons per 1 m2)
×25 m3/h·person (outdoor air volume) ×31.8 kJ/kg (air enthalpy difference indoors/outdoors)
= 190.8 kJ/h·m2(53.0 W/m2)
The Lossnay recuperates approximately 70% of the exhaust air load and saves on approximately 20% of the total load.
Outdoor air
load 33.8%
53.0 W/m2
Indoor
infiltration
heat 30.3%
47.6 W/m2
Indoor
generated heat
(people, lighting
equipment) 35.9%
56.4 W/m2
157.0 W/m2
Dry bulb temp. Relative humidity Wet bulb temp. Enthalpy Enthalpy difference
Cooling Outdoor air 33 °C 63% 27 °C 85 kJ/kg 31.8 kJ/kg
Indoors 26 °C 50% 18.7 °C 53.2 kJ/kg

12
CHAPTER 1 ●Ventilation for Healthy Living
●Determining internal heat gain
When classifying loads, the internal heat gain (indoor generated heat + indoor infiltration heat) will be the value of the outdoor
air load subtracted from the approximate cooling load when it is assumed that there is no reheating load.
(Internal heat gain)
= 157.0 W/m2– 53.0 W/m2= 104.0 W/m2
●This value of internal heat gain is based on assumptions for typical loads. To determine individual levels of internal heat
gain, the following is suggested:
●Indoor generated heat
(1) Heat generated from people
Heat generation design value per person in office
Sensible heat (SH)= 63.0 W/person
Latent heat (LH) = 69.0 W/person
Total heat (TH) = 132.0 W/person
The heat generated per 1 m2of floor space is
(heat generated from people)
= 132.0 W/person ×0.2 person/m2= 26.4 W/m2
(2) Heat generated from electrical equipment (lighting)
The approximate value of the room illuminance and power for lighting for a general office with illuminance of 300 -
350 Lux, is 20 - 30 W/m2.
●Indoor infiltration heat
This is the heat that infiltrates into the building from outside. This can be determined by subtracting the amount of heat
generated by people and lighting from the internal heat gain.
(Indoor infiltration heat)
= 104.0 – (26.4 + 30.0) = 47.6 W/m2
The Lossnay recuperates approximately 70% of the outdoor air load and saves on approximately 20% of the total load.

13
CHAPTER 1 ●Ventilation for Healthy Living
5.3 Ventilation load during heating
●Classification of heating load
Class
Heat lost from walls (qWS)
(a) Indoor heat Heat lost from glass (qGS)
loss Heat loss from conduction & convection (qGS)
Accumulated heat load in walls (qSS)
(b) Outdoor air Sensible heat (qFS)
load Latent heat (qFL)
During heating, the heat generated by people and electrical equipment in the room can be subtracted from the heating load.
However, as the warming up time at the start of heating is short, this generated heat may be ignored in some cases.
Percentage of load
Internal heat loss
In terms of load classification, the internal heat loss is the value of the outdoor air load subtracted from the approximate
heating load.
Internal heat loss = 133.7 W/m2– 56.0 W/m2= 77.7 W/m2
Heating load per unit area
When the outdoor air volume per person is 25 m3/h, and the number of persons per 1 m2is 0.2 persons, the approximate
heating load will be approximately 133.7 W/m2.
●Outdoor air load
Air conditions <Standard design air conditions in Tokyo>
Type of load Load
Outdoor air load 56.0 W/m2
Internal heat 77.7 W/m2
Total 133.7 W/m2
Conditions: Middle floor of a general office building facing south.
When the load per 1 m2of floor area with a ventilation volume of 25 m3/h·person is calculated with the above air conditions,
the following is obtained:
Outdoor air (ventilation) load = 1.2 kg/m3×0.2 persons/m2×25 m3/h·person ×33.5 kJ/kg
= 201.0 kJ/h·m2(56 W/m2)
The Lossnay recuperates approximately 70% of the outdoor air load and saves on approximately 30% of the total load.
Outdoor
air load 41.9%
56.0 W/m2
Indoor heat
loss 58.1%
77.7 W/m2
133.7 W/m2
Dry bulb temp. Relative humidity Wet bulb temp. Enthalpy Enthalpy difference
Cooling Outdoor air 0 °C 50% -3 °C 5.0 kJ/kg 33.5 kJ/kg
Indoors 20 °C 50% 13.7 °C 38.5 kJ/kg

CHAPTER 2
Lossnay Construction and Principle

16
CHAPTER 2 ●Lossnay Construction and Principle
1. Construction and Features of Lossnay
●Lossnay construction
The Lossnay is constructed so that the exhaust air passage from
the indoor side to the outdoor side (RA →EA) and the fresh air
passage from the outdoor side to the indoor side (OA →SA)
cross. The Lossnay heat recovery unit (Lossnay Core) is installed
at this cross point, and recovers the heat by conduction through
the separating medium between these airflows. This enables the
heat loss during exhaust to be greatly reduced.
*RA:Return Air
EA : Exhaust Air
OA : Outdoor Air
SA : Supply Air
SA
(Supply air diffuser)
Supply fan
RA
(Return air)
Exhaust side filter
Lossnay Core
Intake side filter
OA
(Outdoor air)
Exhaust fan
EA
(Exhaust air)
Main Features of Lossnay
(1) Cooling and heating maintenance fees are saved while ventilating.
(2) The capacity and performance of the air conditioner can be reduced.
(3) Dehumidifying during summer, and humidifying during winter is possible.
(4) Comfortable ventilation is possible, (the outdoor air being adjusted to the room temperature.)
(5) Effective sound-proofing.
Note: The dust inlet and outlet are linear in the
actual product.
2. Construction and Principle of Core
●Simple construction
The Lossnay Core is a cross-flow total heat recovery unit
constructed of plates and fins made of treated paper.
The fresh air and exhaust air passages are totally separated
allowing the fresh air to be introduced without mixing with the
exhaust air.
●Principle
The Lossnay Core uses the heat transfer properties and moisture
permeability of the treated paper. Total heat (sensible heat plus
latent heat) is transferred from the stale exhaust air to the fresh air
being introduced into the system when they pass through the
Lossnay. Try this simple experiment. Roll a piece of paper into a
tube and blow through it. Your hand holding the paper will
immediately feel warm. If cold air is blown through the tube, your
hand will immediately feel cool. Lossnay is a total heat exchanger
that utilizes these special properties of paper.
●Treated paper
The paper partition plates are treated with special chemicals so that the Lossnay Core is an appropriate heat recovery unit for
the ventilator. This paper differs from ordinary paper, and has the following unique properties.
(1) The paper is incombustible and is strong.
(2) The paper has selective hydroscopicity and moisture permeability that permits the passage of water vapor only (including
some water-soluble gases).
(3) The paper has gas barrier properties that does not pass gases such as CO2.
SA
Supply air diffuser
(Fresh cold or warm air)
Partition
plate
(Treated
paper)
Spacer plate
(Treated paper)
RA
Return air
(Stale cold or warm air)
Indoors Outdoors EA
Exhaust air
(Stale air)
OA
Outdoor air
(Fresh air)

17
CHAPTER 2 ●Lossnay Construction and Principle
A comparison of the ordinary paper and the Lossnay Core plates is as shown in the table.
Ordinary paper
Water vapor is transferred, but gas elements that are easily
dissolved in water such as CO2, NO2are also transferred.
The contaminated air passes through the plates during
ventilation and returns to the room.
Treated paper
Water vapor is transferred, but gas elements such as CO2,
NO2are not transferred.
The contaminated air does not return to the room when
ventilated.
Highly humid air
Water vapor
Water vapor
CO2NO2
CO2NO2
CO2NO2Water vapor
Water vapor Treatment
(Selective permeable film)
(Incombustible specifications)
Low humid air
Highly humid air
Cellulose
fibers
Low humid air
●Total heat recovery mechanism
Sensible heat and latent heat
The heat that enters and leaves in accordance with changing temperature (rise or drop) is called sensible heat. The heat that
enters and leaves due to the changes in a matter’s physical properties (evaporation, condensation) is called latent heat.
(1) Temperature (sensible heat) recovery
1) Heat conduction and heat passage is performed through a
partition plate from the high temperature to low temperature
side.
2) As shown on the right, the heat recovery efficiency is affected
by the resistance of the boundary layer, and for the Lossnay
there is little difference when compared to materials such as
copper or aluminium which also have high thermal
conductivity.
Heat resistance coefficients
t1
t2
Ra1
Ra2
Rp
Partition plate
Ra1+Ra2»Rp
Treated paper Cu Al
Ra110 10 10
Rp 1 0.00036 0.0006
Ra210 10 10
Total 21 20.00036 20.0006
(2) Humidity (latent heat) recovery
●Water vapor is moved through the partition plate from the
high humidity to low humidity side by means of the
differential pressure in the vapor.
High humidity side
Low humidity side
Partition plate