Episode EA-AMP-HYB-2D-1000 User manual

QUICK START GUIDE
EA-AMP-HYB-2D-1000
EA-AMP-HYB-2D-2000
EA-AMP-HYB-2D-1000
CH.SEL
PROTECT
CH2 ADJUST | SET
MENU
BACK
CLIP
-10
-20
SIGNAL
PROTECT
CH1
CLIP
-10
-20
SIGNAL
ATTENTION! RISQUEDE CHOC ! ÉLECTRIQUE PAS OUVRIR !
CAUTION
RISKOF ELECTRICAL SHOCK!
DONOT OPEN! !
Use only a 250V fuse
Employer uniquement aux
un fusible de 250V
U
C UL
LIFTED
ON
OFF
110 V FUSE T8AH 250V
230V FUSE T4A H250V
118V110-120VAC-60H-230W
230V230-240AC-50Hz-230W
SPEAKER OUT
BRIDGE
DIGITAL
IN
CH1
CH1
CH2
CH2
LINE OUT
CH1
CH1
CH2
CH2
IN
LINK ACT
OUT
LINE IN
TRIGGER
DC 12 V
SERIAL
CONTROL
NETWORK
CONTROL
OUT
CH2 CH1
L

page | 2
www.snapav.com Support 866.838.5052
INTRODUCTION
Thank you for purchasing Episode® Amplifiers. To get started, follow these
instructions. For detailed specifications and configuration recommendations
please see the product manual posted on our website.
This amplifier is a 2 channel (70V or 8ohm selectable on each) designed for
applications requiring two channel stereo audio, or two mono zones of audio with
different sources or levels. Channels can also be bridged to increase output power
and send a singular mono signal.
SOURCE CONNECTIONS
Balanced and unbalanced connections are available as shown below. Line out
connections may be used to send audio signals to other equipment.
DIGITAL
IN
CH1
CH1
CH2
CH2
LINE OUT
CH1
CH1
CH2
CH2
LINE IN
OUT
SPEAKER CONNECTIONS
Use 14 or 16 gauge stranded two-conductor speaker wire. Connect the appropriate
conductor to each screw terminal, observing correct polarity. Bridged markings
are also shown below. Use burial rated wire as necessary for outdoor applications.
SPEAKER OUT
BRIDGE
CH2 CH1
www.snapav.com Support 866.838.5052

page | 3
© 2019 Episode®
IP/OVRC CONTROL
Connect the amplifier to a LAN with internet access to activate an OvrC connection.
Create a new account at www.OvrC.com, or log into an existing account. Select
“Add a Device” and enter the device’s MAC address and serial number (this
information can be found next to the service tag on the product). If OvrC locates
the device, directions to continue setup will be displayed.
The local UI can be accessed without OvrC by entering the IP address into a web
browser. Default login information is shown below:
• Username: episode
• Password: episode
The following settings can be changed in the web GUI:
• System Status
• Power On (Button, 12V Trigger, Audio Sense)
• Input/Output Configuration
• Audio Routing Configuration
• Network IP and Clock Settings
• EQ Presets for Episode Speaker Configurations
• Custom DSP Control
NOTE: To display the IP address of the amplifier, press the “MENU”
button until “Device Info” is displayed, then turn the right-hand knob.
WARRANTY
2-Year Limited Warranty
Episode® Amplifiers have a 2-Year Limited Warranty. This warranty includes
parts and labor repairs on all components found to be defective in material or
workmanship under normal conditions of use. This warranty shall not apply to
products that have been abused, modified or disassembled. Products to be
repaired under this warranty must be returned to a designated service center
with an assigned return authorization (RA) number. Contact technical support at
[email protected] for an RA number.
CONTACTING TECHNICAL SUPPORT
866.838.5052
[email protected]
WARNING: This product can expose you to chemicals including Cadmium,
which is known to the State of California to cause cancer and Reproductive
harm. For more information go to www.P65Warnings.ca.gov.

© 2019 Episode®
Rev: 190402-1120