EPS 305 User manual

MODEL 305
TOKEN STATION
INSTALLATION & PARTS
MANUAL
ENGINEERED PARKING SYSTEMS
25010 AVENUE TIBBITTS
VALENCIA, CA 91355
[phone]
[phone]
www.epsinfo.com

GENERAL INFORMATION:
WARRANTY:
All equipment manufactured by Engineered Parking Systems is warranted against defects
in material and workmanship for one full year from date of shipment. All equipment is
tested and inspected before shipment. The warranty covers repair or replacement of any
part which fails under normal usage. Transportation and labor charges are to be paid by
the customer.
HOUSING:
The token station is constructed of fourteen gauge steel. It is of welded construction with
a hinged access door. The door is fitted with a mounted key lock. Two keys are provided.
The housing is finished with two coats of industrial baked enamel.
TOKEN MECHANISM:
The token station comes standard with a 7/8" (.900) or 1" (.984) token acceptor. Other
sizes are available.
ELECTRICAL:
The token station does not require electricity to operate. The token reject button is supplied
with a back light that requires a 14 volt power source to illuminate.
INSTALLATION INSTRUCTIONS:
The unit should be installed on a concrete foundation not more than 6" above the
driveway. (See installation drawing) Mount pedestal to concrete foundation with four
anchor bolts. MAKE SURE TOKEN STATION IS LEVEL.
CONNECTIONS:
Connect common and normally open terminals from token vend switch to terminals 7
and 10 in model 301 barrier gate. For other brands of gates, connect common and normally open
terminals from token vend switch to gate open input in gate operator.

ADJUSTMENT
All Ultimechs are adjusted at the factory for maximum performance and no adjustment
should be necessary. If the mech has been disassembled or if more critical adjustments
are desired, the following adjustment procedure is recommended (make sure that the
mech is upright and level):
GATE
To adjust for slightly thicker coins or improve acceptance. turn the gate adjustment screw
clockwise. To adjust for thinner coins or improve security, turn the screw counterclockwise.
MAGNET
Turn the magnet holder adjust screw counterclockwise until a coin dropped into the mech
will not pass. Turn the screw clockwise until the coin just passes through. Turn the screw a
further 1/2 turn clockwise for proper operation.
SEPARATOR
Loosen the screw holding the separator. Align the right edge of the separator with the
innermost mark on the back of the main bezel. This is the standard adjustment and
should be acceptable for most locations. As coins are dropped through, observe where
the coin hits the separator. By moving the separator back and forth slightly, the desired
acceptance of good versus bad coins can be obtained. Tighten the screw and retest to be
sure of proper operation.
The entry restrictor, cradle and sizing lever are specially tooled are not adjustable.
MAINTENANCE
The mech can be cleaned with any mild cleaner or even in a dishwasher. Rinse and
dry completely. Make sure that the cradle and sizing lever move freely.
Do not use grease or oil on any part of the mech as this will attract dust and dirt which
will slow down the coin and cause poor acceptance.
The magnet can be cleared of metal filings by guiding the edge of a screwdriver along
the inside edges of the magnet holder. The filings will stick to the screwdriver.

PARTS LIST
MODEL 305 TOKEN STATION
QUANTITY PART NUMBER DESCRIPTION
1 205-3* .900 TOKEN ACCEPTOR
1 205-4* .984 TOKEN ACCEPTOR
1 205-9 .900 ACCEPTOR WI FRONT PLATE
1 205-10 .984 ACCEPTOR WI FRONT PLATE
1 492-41 (42-7087-00) VEND SWITCH & WIRE ASSY.
1 306-6 36” PEDESTAL (MOUNTING POST)
1 806-1 CAM LOCK
1 1051-40 DECAL, "TOKENS ONL Y"
1 9050-1 STEEL HOUSING
1 9050-2 DOOR
1 9050-3 TOKEN BOX