Erbauer ERB596CSW User manual
2000W 235mm CIRCULAR SAW ERB596CSW
ERB596CSW
Original Instructions
(Version 1.0)
2000W 235mm CIRCULAR SAW ERB596CSW
GUARANTEE
This product carries a 2 years guarantee. If your product develops a fault
purchased.
- Fair wear and tear
- Misuse or abuse
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This
product should give you reliable service but for your peace of mind this
power tool does carry a 2 year guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
GENERAL POWER TOOL SAFETY WARNINGS
Warning: Read all safety warnings and all instructions.
Save all warnings and instructions for future reference.
power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
2000W 235mm CIRCULAR SAW ERB596CSW
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
or medication.
b. Use personal protective equipment. Always wear eye
protection.
safety shoes, hard hat, or hearing protection used for appropriate
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating part of the power tool
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving parts.
parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for
your application.
and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools.
power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are
f. Keep cutting tools sharp and clean.
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
result in a hazardous situation.
5. Service
using only identical replacement parts. This will ensure that
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW
protection.
practicable.
2000W 235mm CIRCULAR SAW ERB596CSW
the rating plate.
etc.
upwards or at the side.
saw no load speed.
cable and pipes.
blades.
Warning:
a. Keep hands away form cutting area and the blade. Keep
your second hand on auxiliary handle, or motor housing. If
both hands are holding the saw, they cannot be cut by the blade.
b. Do not reach underneath the work-piece. The guard cannot
c. Adjust the cutting depth to the thickness of the work-piece.
Less than a full tooth of the blade teeth should be visible below
the work-piece.
d. Never hold piece being cut in your hands or across
your leg. Secure the work-piece to a stable platform. It
e. Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may contact
hidden wiring or its own cord.
the operator.
f. When ripping always use a rip fence or straight edge guide.
blade binding.
g. Always use blades with correct size and shape (diamond
versus round) of arbor holes.
of control.
h. Never use damaged or incorrect blade washers or bolt. The
blade washers and bolt were specially designed for your saw, for
FURTHER SAFETY INSTRUCTIONS FOR CIRCULAR SAWS
KICKBACK CAUSES AND RELATED WARNINGS
- Kickback is a sudden reaction to a pinched, bound or
and out of the workpiece toward the operator;
- When the blade is pinched or bound tightly by the kerf closing
rapidly back toward the operator;
- I
at the back edge of the blade can dig into the top surface of the
toward the operator.
procedures or conditions and can be avoided by taking proper
precautions as given below.
position your arms to resist kickback forces. Position
your body to either side of the blade, but not in line with
the blade.
but kickback forces can be controlled by the operator, if proper
2000W 235mm CIRCULAR SAW ERB596CSW
precautions are taken.
b) When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless
in the material until the blade comes to a complete stop.
Never attempt to remove the saw from the work or pull the
saw backward while the blade is in motion or kickback may
occur.
cause of blade binding.
c) When restarting a saw in the workpiece, centre the saw
blade in the kerf and check that saw teeth are not engaged
into the material.
d) Support large panels to minimise the risk of blade pinching
and kickback. Large panels tend to sag under their own
near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or
friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be
tight and secure before making cut.
g) Use extra caution when making a “plunge cut” into existing
walls or other blind areas.
SAFETY INSTRUCTION FOR CIRCULAR SAW WITH INNER
PENDULUM GUARD
a) Check lower guard for proper closing before each use. Do
not operate the saw if lower guard does not move freely
and close instantly. Never clamp or tie the lower guard into
the open position. If saw is accidentally dropped, lower guard
any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard
and the spring are not operating properly, they must be
serviced before use.
c) Lower guard may be retracted manually only for special
cuts such as “plunge cuts” and “compound cuts.” Raise
lower guard by retracting handle and as soon as blade
enters the material, the lower guard must be released. For
d) Always observe that the lower guard is covering the blade
An unprotected,
coasting blade will cause the saw to walk backwards, cutting
blade to stop after switch is released.
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
Construction workers are one of the at-risk groups within this because of the dust that they
Lung cancer
Silicosis
The risk of lung disease is linked to people who regularly breathe construction dust over a
used.
2. Use a less powerful tool e.g. a block cutter instead of angle grinder.
2000W 235mm CIRCULAR SAW ERB596CSW
Warning: Some dust particles created by power sanding, sawing, grinding, drill
and other construction jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm.
To
• Work in a well-ventilated area.
designed
VIBRATION
daily basis and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Typical weighted vibration cutting
wood
h.w
used with the current guidance on vibration.
Warning:
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
Warning:
working period on this tool.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions and keep well lubricated
(where appropriate)
Health Surveillance
any vibration related diseases at an early stage, prevent disease progression and help
Double insulation
earthed.
Important note
with a two-core cable and plug.
2000W 235mm CIRCULAR SAW ERB596CSW
SYMBOLS
Warning
Double insulation
Wear ear protection Wear eye protection
Wear gloves
Waste electrical products should not be disposed of with household waste.
or retailer for recycling advice.
12
3
4
7
5
6
8
9
10
11
12
13
14
15
1716
18
19
2000W 235mm CIRCULAR SAW ERB596CSW
1. HAND GRIP AREA
2. ON/OFF SWITCH
3. AUXILIARY HANDLE
4. BEVEL SCALE
5. BEVEL LOCK BUTTON
6. PARALLEL GUIDE LOCKING SCREW
7. 45OMARK
8. 0OMARK
9. PARALLEL GUIDE
10. FIXED GUARD
11. SAW BLADE
12. LOWER BLADE GUARD
13. LOWER GUARD LEVER
14. BASE PLATE
15. DUST TUBE
16. LOCK OFF BUTTON
17. SPINDLE LOCK BUTTON
18. DEPTH OF CUT SCALE
19. DEPTH OF CUT ADJUSTMENT LEVER
20. HEX KEY (See Fig. 1-2)
21. BLADE BOLT (See Fig. 1-2)
22. OUTER FLANGE (See Fig. 1-2)
23. INNER FLANGE (See Fig. 1-2)
24. SPINDLE (See Fig. 1-2)
Rated voltage
Rated power 2000W
No-load speed
evel capacity o
90o
o
Protection class
Machine weight
NOISE INFORMATION
A weighted sound pressure LpAPA
A weighted sound power LwAWA
ACCESSORIES
Parallel guide 1pc
Vacuum adapter (32mm) 1pc
Hex key (6mm) 1pc
Blade (235mm×2.8mm×30mm, 36T) 1pc
Dust tube 1pc
Screws for dust tube (M4X10mm) 2pcs
TECHNICAL DATA
2000W 235mm CIRCULAR SAW ERB596CSW
OPERATING INSTRUCTIONS
NOTE:
instruction book carefully.
INTENDED USE
cutting wood in straight cutting lines and with bevel
piece.
HOW TO ASSEMBLE YOUR SAW BLADE (See
Fig. 1-1, 1-2, 1-3)
locking the spindle. Push and hold the spindle
(21) by turning it in a counterclockwise direction.
allow the saw blade (11) to be located onto the
clockwise direction.
WARNING: Saw blade teeth are very sharp.
Wear gloves for protection.
DUST EXTRACTION OUTLET (See Fig. 2)
Fig. 1-1
Fig. 1-2
Fig. 1-3
24 23 22 21 20
11
Fig. 2
SAFETY ON/OFF SWITCH
Your switch is locked off to prevent accidental
off switch.
HAND GRIP POSITION
operating. The right and wrong ways to support
DEPTH OF CUT ADJUSTMENT (See Fig.4-1, 4-2)
the saw body until the blade is at the right depth.
your depth of cut so the blade can cut through the
Fig. 3-1
Fig. 3-2
Fig. 4-2
RIGHT
WRONG
18
19
19
Fig. 4-1
2000W 235mm CIRCULAR SAW ERB596CSW
BASE PLATE ANGLE ADJUSTMENT (See Fig. 5)
accurate work to set the angle with a protractor
to possible inaccuracy.
PARALLEL GUIDE ADJUSTMENT (See Fig.6)
edge at a chosen distance. Slide the parallel guide
cutting distance and tighten screw to lock into
using with a parallel guide (9). For straight cuts,
a trial cut to check the setting.
Fig. 5
Fig. 6
4
5
9
14
WORKING HINTS FOR YOUR CIRCULAR SAW
usage at very low speeds. Always use a blade
of blade teeth increases. Always ensure that the
quality of the cut. The blade cuts on the upward
edges of your work piece. When cutting, ensure
MAINTENANCE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication
parts in your power tool. Never use water or
clean with a dry cloth. Always store your power
slots clean. Keep all working controls free of
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
Local Authority or retailer for recycling advice. For
Other manuals for ERB596CSW
1
This manual suits for next models
1
Table of contents
Other Erbauer Saw manuals
Erbauer
Erbauer ERB1721A User manual
Erbauer
Erbauer EDD18-Li-2 User manual
Erbauer
Erbauer 3663602796244 User manual
Erbauer
Erbauer ECS18-Li User manual
Erbauer
Erbauer ERI490CSW User manual
Erbauer
Erbauer ERA568RSP User manual
Erbauer
Erbauer ERF298MSW User manual
Erbauer
Erbauer ERB611MSW User manual
Erbauer
Erbauer ERB690CSW User manual
Erbauer
Erbauer ERB610MSW User manual
Erbauer
Erbauer ERB2504SE User manual
Erbauer
Erbauer ERS1100-1 User manual
Erbauer
Erbauer ERB2502SE User manual
Erbauer
Erbauer ERN642ATL-I User manual
Erbauer
Erbauer EMCS650 User manual
Erbauer
Erbauer ERB238MSW User manual
Erbauer
Erbauer ERB1590LA User manual
Erbauer
Erbauer ERB110SSW User manual
Erbauer
Erbauer ERB2151SE User manual
Erbauer
Erbauer ETS1500-A User manual
