Ergo In Demand CrossRoads User manual

Top Assembly
Shared End Panel
Right End Panel
Base Assembly
Glides
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
4
1
/ 2 " Hex Head Bolts
with Lock Washers
and Flat Washers
Figure 4
Flat Washer
and Hex Nut
Tools Required:
•#2 Phillips screwdriver
•1/2" socket
•Socket wrench
Hardware Included:
•#8 x
5/8" screws
•#8 x 11/4" screws
•#10 x 11/2" pan head screws
•5/16
" x 2" hex head bolt
•5/16
"x41/2" hex head bolt
•5/16
" lock washer
•5/16
" at washer
•5/16
" hex nut
•Metal pins
1.Set back edge of left end panel on at
surface (holes to inside – if it’s a
curved end panel make sure the
curved edge is up).
2. Align the side holes in the base
assembly with the lower holes in the
left end panel. Insert 2" hex head bolts
with lock washers and at washers into
the base and end panel (Figure 1).
3. Align the side holes in the top
assembly with the upper holes in the
left end panel (Figure 2). Make sure
the faceplate on the top assembly is to
the front and that the back panel
groove is to the back. Insert 2" hex
head bolts with lock washers and at
washers into the top assembly and
end panel. Tighten.
4. For single starter unit (stand-alone)
and nal end panel for connecting
units: Take the right end panel (holes
to inside) and align the side with the
holes in both the base and the top
assembly (Figure 3). Insert 2" hex
head bolts with lock washers and at
washers into the base and top
assembly. Tighten.
5. For adder units (connecting) – Align
the side holes in the shared panel
(holes both sides) with the holes in
both the base assembly and the top
assembly. Insert 41/2" hex head bolts
with lock washers, at washers and
nut into the base assembly. Do not
tighten (Figure 4).
6. Align the side holes in both the base
and top assembly with the side holes
in the right end panel. Insert 2" hex
head bolts with lock washers and at
washers into base assembly and top
assembly (Figure 4).
7.Tighten all 2" and 41/2"hex head bolts.
Insert glides into all end panels.
Left End Panel
and Flat Washers
Base Assembly
Base Assembly.eps
Figure 1
Left End Panel
and Flat Washers
Base Assembly
Assembly
Top Asm.eps
Right End Panel
Rt. End Pnl Install.eps
Glides
Figure 3
Left End Panel
and Flat Washers
Base Assembly
Top Assembly
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must
be tightened securely and must be checked periodically
after assembly. Failure to assemble properly, or to secure
parts may result in assembly failure and injury.
Ergo In Demand, Inc. •4900 Industry Drive •Central Point, OR 97502 •Tel [phone] •www.ergoindemand.com
Figure 1
Assembly Instructions
CrossRoads®Newspaper Display Unit
August 2008
Figure 2
Figure 3
Figure 4

Right End Panel
Base Assembly
Back Panel
Side Groove
Glides (2)
#8 x
5
/
8
"
Support Screws (2)
Back Panel
Shelf Back Inst.eps
Figure 5 & 6
Right End Panel
Base Assembly
Back Panel
Side Groove
Glides (2)
#8 x
5
/ 8 "
Support Screws (2)
Back Panel
Shelf Back Inst.eps
Figure 5 & 6
8. For optional back panel, slide the back
panel into the side grooves of the end
panels and top assembly. Insert #8 x
5/8" screws into the groove directly
below the back panel to keep the panel
raised o the oor (Figures 5 & 6).
9. Carefully tip the shelving unit into an
upright position. Note that two or
more assemblers are recommended
when multiple units are connected.
10. Bottom shelf. Insert (4) metal pegs
into pre-drilled holes just above the
base assembly. Lay bottom shelf with
routed side down and align onto metal
pegs (Figure 7).
11. Attach wood cleats to the bottom side
of the xed shelf using #8 x 11
/4"screws.
One cleat is needed for each side of
shelf. Rest shelf on four metal pegs.
Attach xed shelf with cleats to the
end panels using #8 x 11
/4" screws
(Figure 7). Note: for 60” high units,
xed shelf is approximately 431
/4" from
top of the bottom shelf. For 82" high
units, xed shelf is approximately 5013
/16 "
from top of the bottom shelf.
12.Adjustable shelves for 82" high units
only. Insert (4) metal pegs into pre-
drilled holes at desired adjustable
shelf heights. Set each shelf onto the
metal pegs with routed side down.
Repeat for each adjustable shelf
(Figure 7).
13.Attach notched rack to panels using
two #10 x 11/2" screws. Note: for 60"
high units locate upper screw 36 3
/4"
above bottom shelf and 15/8" from
back panel. For 82" high units, locate
upper screw 443/4"above bottom shelf
and 15
/8" from back panel. Align the
bottom of the rack with the front edge
of the shared panel or 1" in from the
center of the arc of the end panels.
Attach with #10 x 11/2" screw.
14. Set up to eight newspaper display
rods into notched racks.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and injury.
CrossRoads ®Newspaper Display Unit
Assembly Instructions
Figure 6
Bottom Shelf
Base Assembly
(2 per Shelf)
Fixed Shelf
(4 per Shelf)
(4 per Shelf)
#10 x 1
1
/ 2 "
Pan Head Screws
Display Rod
Figure 7
Figure 5
Ergo In Demand, Inc.
4900 Industry Drive
Central Point, OR 97502
Contact Information:
800.888.6024 (Toll Free)
541.779.3763 (Office)
541.779.0829 (Fax)
[email protected] (Email)
www.ergoindemand.com (Website)