Safavieh Furniture Errington CNS9000A User manual

NOTICE
PREPARATION
* Please make sure that you have all parts indicated they are in good condition before you
begin assembly of this item. Refer to part list and hardware list below for guidance .
* This item should be assembled on a soft surface to prevent scartching the finish during
assemby.
* This item may require periodic tightening.
* If you are having difficulty, our friendly customer care team is always here to help . Please
email [email protected]
* Before beginning assembly of product , make sure all parts are presnt . Compare parts with parts
contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the pdoduct.
* Estimated Assembly time : 10 minutes
* Tools Required for Assembly (included): Allen key
CARE AND MAINTENANCE
*Spot clean using a mild water-free solvent. Only a professional cleaner should undertake a
complete overall cleaning.
*The use of steam or water-based cleaners may cause excessive shrinking or staining.
The legs and hardware are located under the drawer
Hw3 Allen key 4 mm
2X
2X
Flat washer 16 mm
Allen bolt 45x6 mm
A
B
Hw1
Hw2
Shelf
Leg
24X
24X
1X
PIECE QUANTITY
DESCRIPTION PICTURE
Item# CNS9000A
Product dimensions: 47.2"L* 13.7"W*30"D
2X
CLeg
WARNING
Weight Capacity - 55 LBS
Warning : Do not stand on Table
Warning : Do not over torque bolts.
Item# CNS9000A
Product dimensions: 47.2"L* 13.7"W*30"D
WARNING
Weight Capacity - 55 LBS
Warning : Do not stand on Table
Warning : Do not over torque bolts.
NOTICE
* Please make sure that you have all parts indicated and are in good condion before you begin assembly
of this item. Refer to part list and hardware list below for guidance .
* This item should be assembled on a so surface to prevent scratching the finish during assembly.
* This item may require periodic ghtening.
* If you are having difficulty, our friendly customer care team is always here to help . Please
email [e-mail]
* Before beginning assembly of product , make sure all parts are present . Compare parts with parts
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly me : 10 minutes
* Tools Required for Assembly (included): Allen key
CARE AND MAINTENANCE
*Spot clean using a mild water-free solvent. Only a professional cleaner should undertake a
complete overall cleaning.
*The use of steam or water-based cleaners may cause excessive shrinking or staining.
PREPARATION
contents list and hardware contents list.
Part List and Hardware List
Hw3 Allen key 4 mm
1X
2X
Flat washer 16 x 8 mm
Allen bolt 6 X 1 X 45 mm
A
C
Hw1
Hw2
Shelf
Leg
24X
24X
1X
PIECE DESCRIPTION PICTURE QUANTITY
BLeg 2X

PREPARATION
* Before beginning assembly of product , make sure all parts are presnt . Compare parts with parts
contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the pdoduct.
* Estimated Assembly time : 10 minutes
* Tools Required for Assembly (included): Allen key
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [email protected]
Hw3
Hw1
Hw2
6X
B
B
A
A
1
2
Hw3
Hw1
Hw2
6X
PREPARATION
* Before beginning assembly of product , make sure all parts are present . Compare parts with parts
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly me : 10 minutes
* Tools Required for Assembly (included): Allen key
contents list and hardware contents list.
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [e-mail]
Leg
STEP1
Unwrap the legs & take out legs.
Hardware
Open the hardware pouch & take out hardware.
STEP2
Place the Table upside down on a clean surface.
Align legs on both sides of Table as per side holes
present on either side of Table.
STEP3
Put the washer on the Bolt in the order shown in
picture.
STEP4
Insert Allen Bolt (Hw1) with Washer (Hw2)
ghten with Allen Key (Hw3).Don’t over ghten.
Hw2 Hw1
Hw2
Hw1
Hw3
STEP5
Align the shelf (A) with the frame as shown.
A
B
B
A
B
B
Hw2
Hw1
Hw3
STEP6
Put the washer on the Bolt in the order shown in
picture.
Hw2 Hw1
Hw2
Hw1
Hw3
A
B
A
B

PREPARATION
* Before beginning assembly of product , make sure all parts are presnt . Compare parts with parts
contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the pdoduct.
* Estimated Assembly time : 10 minutes
* Tools Required for Assembly (included): Allen key
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [email protected]
The legs and hardware are located under the drawer
STEP2 PUT THE WASHERS (H2) ON THE ALLEN
BOLT (H1) IN THE ORDER SHOWN IN THE
PICTURE
STEP3 INSERT ALLEN BOLT WITH WASHER INTO
THE BOTTOM PANEL HOLE AS SHOWN AND
TIGHTEN WITH ALLEN KEY(H3).
STEP1 OPEN THE ZIPPER ON THE INSIDE OF THE
DRAWER AND TAKE OUT LEGS AND HARDWARE
C
C
B
A
A
B
4X
Hw3
Hw1
Hw2
2X
Hw3
Hw1
Hw2
PREPARATION
* Before beginning assembly of product , make sure all parts are present . Compare parts with parts
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly me : 10 minutes
* Tools Required for Assembly (included): Allen key
contents list and hardware contents list.
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [e-mail]
STEP8
Align the leg (C) holes with leg (B) holes.
STEP9
Put the washer on the Bolt in the order shown in
picture.
STEP10
Insert Allen Bolt (Hw1) with Washer (Hw2)
ghten with Allen Key (Hw3).Don’t over ghten.
STEP11
Repeat step 10 for, other side leg, flip the Table
upright with help.
Hw2 Hw1
Hw2
Hw1
Hw3
PREPARATION
* Before beginning assembly of product , make sure all parts are presnt . Compare parts with parts
contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the pdoduct.
* Estimated Assembly time : 10 minutes
* Tools Required for Assembly (included): Allen key
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [email protected]
The legs and hardware are located under the drawer
STEP2 PUT THE WASHERS (H2) ON THE ALLEN
BOLT (H1) IN THE ORDER SHOWN IN THE
PICTURE
STEP3 INSERT ALLEN BOLT WITH WASHER INTO
THE BOTTOM PANEL HOLE AS SHOWN AND
TIGHTEN WITH ALLEN KEY(H3).
STEP1 OPEN THE ZIPPER ON THE INSIDE OF THE
DRAWER AND TAKE OUT LEGS AND HARDWARE
C
C
B
A
A
B
4X
Hw3
Hw1
Hw2
2X
Hw3
Hw1
Hw2
Hw2
Hw1
Hw3 C
B
C
B
A
A
Hw2
Hw1
Hw3
Hw2
Hw1
Hw3
STEP7
Insert Allen Bolt (Hw1) with Washer (Hw2)
ghten with Allen Key (Hw3).Don’t over ghten.