Ergo EMZ400 User manual
EMZ400
Direct Wall Mount Instructions
See it your way...
Safety Instructions
CAUTION: This mount is intended for use only with the maximum weights
indicated. Use with at screens heavier than the maximum indicated may
result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference. Please check carefully
to make sure there are no missing or defective parts – defective parts must never be used.
ErgoMounts Limited, its distributors and dealers are not liable or responsible for damage or injury
caused by improper installation, improper use or failure to observe these safety instructions. In such
cases, all guarantees will expire.
General
ErgoMounts Limited recommends that a professional AV installer or other suitably qualied person
install this product. Great care must always be taken during installation as most AV equipment is of
a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to mount
this product correctly may cause serious injury or death both during installation and at any time
thereafter.
Do not mount any AV equipment that exceeds the specic weight limit of the product you are
installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product
to product.
Product Location
Please pay careful attention to where this product is located. Check the load capacity of wall prior to
installation as some walls are not suitable. Designed for indoor use, this mount is suitable for public
or home installation. If located in a public or frequently populated area ensure that the product is
out of the immediate reach of people. If any AV equipment is to be suspended over the likely path
or location of people then great care should be taken to secure all parts of the installation from
falling. If you install this product on drywall it must be securely xed to a wooden stud, concrete
block or other permanent structure behind the drywall board. Installing on drywall boards alone
will not support the weight of most AV equipment.
When drilling holes in walls it is essential to avoid contact with electrical cables and water or
gas pipes contained within. Use of a good quality live wire detector and hidden object locator is
therefore recommended. Only drill intro structures when you are sure it is safe to do so.
Fixing Hardware
It is highly recommended that all wall xing screws be used where supplied and that the purpose of
all other xing hardware is fully understood. In some cases more AV equipment xing hardware will
be supplied to accommodate dierent models of equipment and set up congurations.
The installer must be satised that any supplied xing hardware is suitable for each specic
installation. If any xing screws or included hardware is deemed not sucient for a safe installation
then please consult a professional or your local hardware store.
Hazard Limitation
When routing cables, take advantage of any built in cable management features that the product
might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect
of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or
trapping of ngers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling, installing
and adjusting during setup.
Immediately after installations double-check that the work done is safe and secure. Double-check
all necessary xings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its xing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualied person.
Parts List
Parts List
Installation
1: Attach wall plate to either a concrete of stud wall.
i. Concrete wall
ii. Stud wall
Installation
2: Attach interface arms to at screen using interface kit.
Installation
3: Hook at screen onto wall mount (this may require 2 people)
Installation
4: Screen levelling adjustment (Optional).
5: Secure interface arms to wall plate.
Installation
6: Adjust the tilt by hand.
Dimensions
Notes
ErgoMounts Limited
Unit 10
Pegasus Court
North Lane
Aldershot
Hampshire
GU12 4QP
T +44 (0)1252 333326
F +44 (0)1252 330006
www.ergomounts.co.uk
© ErgoMounts 092017
See it your way...
Other Ergo Rack & Stand manuals
