ergoline VITALITY UV 50 User manual

1029445-00 en 0/ / 2.2023
Translation of the original operating instructions
VITALITY UV 50
Operating instructions

Legal notice
2/72
Legal notice
Manufacturer: JK-Products GmbH
Köhlershohner Strasse 60
53578 Windhagen
GERMANY
Tel: [phone] / 818-140
Fax: [phone] / 818-166
Customer service /
Technical service
(Spare part orders
for components):
JK-International GmbH,
JK-Global Service Division
Köhlershohner Strasse 60
53578 Windhagen
GERMANY
Tel: [phone] / 818-861
Fax: [phone] / 818-205
E-mail: [e-mail]
Spare part orders for
consumables:
JK-International GmbH,
JK-Licht Division
Köhlershohner Strasse 60
53578 Windhagen
GERMANY
Tel: [phone] / 818-600
Fax: [phone] / 818-615
E-mail: [e-mail]
DANGER!
Failure to observe these operating instructions:
may result in serious injury and death,
can result in damage to the unit and to the envi-
ronment.
–Read these instructions carefully before putting
this unit into operation.
–Please observe the instructions and the code of
conduct required to operate the unit safely.
–Please makethe operating instructions and addi-
tional information from the manufacturer availa-
ble to the personnel at their workplace.
Copyright
The copyright remains with JK-Holding GmbH.
The contents may not be partially or completely duplicated, distributed
or utilized for competitivepurposes without authorization ordisclosed
to other parties.
The right to make technical changes in regard to the figures andinfor-
mation contained in these operating instructions is reserved!

Table of contents
02/2023 1029445-00 Operating instructions – 3/72
Table of contents
1Safety instructions and warnings....................................... 6
1.1 General......................................................................................6
1.1.1 Definitions.................................................................................6
1.1.2 Symbol explanation..................................................................7
1.2 Intended use .............................................................................8
1.3 Foreseeable misuse.................................................................8
1.4 Tanning safety information......................................................9
1.4.1 Prohibited usage.......................................................................9
1.4.2 Important notes......................................................................10
1.4.3 Skin type descriptions............................................................11
1.4.4 Tanning times EN (UV type 2)................................................12
1.5 Safety instructions and warnings..........................................13
1.5.1 Operator's obligations............................................................13
1.5.2 Personnel training...................................................................13
1.5.3 Scope of delivery ....................................................................13
1.5.4 Transport, assembly and setup.............................................13
1.5.5 Commissioning.......................................................................16
1.5.6 Operation and maintenance...................................................16
1.5.7 Decommissioning...................................................................17
1.5.8 Storage....................................................................................17
1.5.9 Disposal...................................................................................17
1.5.10 Directives.................................................................................18
1.5.11 Export......................................................................................18
1.5.12 AUX (music)............................................................................19
1.5.13 Technical modifications.........................................................19
1.6 Signs and stickers onthe unit................................................20
1.7 Preclusion of damage............................................................25
1.8 Exclusion of liability................................................................25
2Description ...................................................................... 26
2.1 Scope of delivery ....................................................................26
2.1.1 Optional...................................................................................26
2.2 Equipment...............................................................................26
2.3 Unit description.......................................................................27
2.4 Accessories (optional)...........................................................28
2.5 Functional description............................................................28

Table of contents
4/72
3Operation..........................................................................29
3.1 User safety information .........................................................29
3.2 Tanning - but correctly!..........................................................29
3.3 Operating overview.................................................................31
3.3.1 Professional Setup Manager.................................................32
3.4 Functions................................................................................33
3.4.1 Navigation...............................................................................33
3.5 Start.........................................................................................36
3.6 Coupling with Bluetooth® devices........................................37
3.7 Listening to music..................................................................39
3.8 Smartphonewireless charging (QI) (optional) .....................39
4Cleaning and maintenance................................................40
4.1 Safety instructions when undertaking cleaning or
maintenance work..................................................................40
4.2 Faults.......................................................................................41
4.3 Cleaning..................................................................................41
4.3.1 Disinfection.............................................................................41
4.3.2 Cleaning the surfaces............................................................42
4.3.3 Lamps .....................................................................................42
4.4 Cleaning plan..........................................................................43
4.5 Maintenance...........................................................................44
4.5.1 Acrylic glass............................................................................44
4.5.2 REMOTE SERVICE (optional).................................................45
4.6 Maintenance plan...................................................................45
4.7 Cleaning and maintenancework preparation.......................47
4.7.1 Service kit................................................................................47
4.7.2 Lift up the acrylicglass panel and removethe partition......48
4.7.3 Remove the canopy panel......................................................49
4.7.4 Remove the side section panel..............................................50
4.7.5 Open the bed base..................................................................50
4.8 Instructions for replacing the lamps.....................................52
4.8.1 Low-pressure lamps...............................................................53
4.9 Cleaning or replacing lamps in the base...............................54
4.10 Cleaning or replacing the lamps in the side section............54
4.11 Cleaning or replacing lamps in the canopy...........................55
4.12 Cleaning the filters in the base..............................................55
4.13 Cleaning the canopy filter......................................................56
4.14 Air conditioning:
Empty the condensation tank and clean the filter................57
4.15 AQUA / AROMA system maintenance..................................60
4.15.1 Changing the AROMA canister..............................................60
4.15.2 Replacing the AQUA SYSTEM canister.................................61
4.16 Cleaning the air intake openings...........................................62

Table of contents
02/2023 1029445-00 Operating instructions – 5/72
5Technical data................................................................. 63
5.1 Power, connection rating and noise level..............................63
5.2 Dimensions.............................................................................64
5.3 Lamp sets................................................................................65
5.3.1 VITALITY 50............................................................................65
5.4 Spare parts and accessories.................................................66
6Appendix ......................................................................... 67
6.1 JK timer controls....................................................................67
6.2 Equivalence key range............................................................67
6.2.1 Description of the equivalence keys for
fluorescent lamps...................................................................68
7Index................................................................................ 69

Safety instructions and warnings
6/72
1 Safety instructions and warnings
To ensuresafe operation of the device, it is necessary to read the fol-
lowing safety instructions andwarnings carefully and comply with
them.
These instructions shouldbe retained forfuture use.
The safety instructions summarized here are repeated in the corre-
sponding chapters, where necessary.
1.1 General
1.1.1 Definitions
Operator
Person who provides the devices described here to users ona com-
mercial basis. The operator is responsible for thecorrect operation of
the deviceas well as compliance with the maintenanceintervals.
User
A person who uses the device at a commercial location.
Personnel
People who are responsible for the operation, cleaning and general
maintenance work andwho instruct the users in the operation of the
devices.
Electrician
A person with suitable professional training, knowledge, experience
and knowledge of the applicable regulations which enable them to
identify and avoid the dangers which can arise from working with elec-
tricity.
Authorized, trained and qualified personnel
Qualified staff from an external company who havebeen trained and
authorized by the manufacturer to undertakeassembly and mainte-
nance work on specific equipment.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 7/72
1.1.2 Symbol explanation
The following types of safety notices are employed in these operating
instructions:
DANGER!
Type and source of hazard
This safety notice indicates the existence of a direct
danger to body and life.
DANGER!
Type and source of hazard
This safety notice warns of dangers to body and life
which are caused byelectricity.
WARNING!
Type and source of hazard
This safety notice warns of machine, material or envi-
ronmental damage.
NOTE:
This symbol does not identify any safety notices, but
provides additional information to better understand
the processes.

Safety instructions and warnings
8/72
1.2 Intended use
This unit serves the purposeof cosmetic tanning for one adult person
with skin suitable for tanning. More detailed information can also be
found on pages 11 and29.
This deviceis intended only for commercial use and not for private
use.
Some people are not permitted to usethe device, see page 9.
The devicemay not be used by people with reduced physical, sensory
or mental capabilities or who have insufficient experience and/or
knowledge without supervision. A person responsible for their safety
must ensure, eitherby supervisionor instruction, that the device is
used correctly and safely. If thereis any doubt, use of the device by
such categories of persons is to be forbidden!
The devicemay only be operated with thespecified orequivalent
lamps. The tanning times given in this instruction manual are valid
only for the specified lamp set.
Any otheruse shall be considered improper. The manufacturer cannot
be held liable for damage or injuries resulting from this. The operator
bears the sole risk for this.
Proper use also includes compliancewith the manufacturer’s instruc-
tions and its operating and maintenance conditions. The unit may only
be operated, maintained and repaired by trained professionals familiar
with this unit andwho have been informed ofthe dangers involved.
1.3 Foreseeable misuse
The following uses of the device are explicitly prohibited:
The devicemay not be used by several people at the same time.
The acrylicglass panel may otherwise break and causeinjuries.
People with a body weight of more than 135 kg may not use the
device. The acrylic glass panel may otherwise break and cause in-
juries.
Exceeding the specified tanning times may result in burns and
long-term skin damage.
When the device is in use no other people may remain in the
cabin, in particular no children.
While using the device no pets maybe present in the cabin.
People under 18 years of age may not usethe device.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 9/72
1.4 Tanning safety information
1.4.1 Prohibited usage
DANGER!
UV radiation
Danger of skin and eye injuries or skin diseases!
–Please observe the following instructions.
The following people may not use the device:
People under 18 years of age
People who cannot tan
People who cannot tan inthe sunwhithout risking a sunburn
People who easily sunburnwhen in the sun
People with acute sunburn
People who repeatedlysuffered from serious sunburnduring
childhood
People with naturally red hair
People with atypically discoloured areas of skin
People who have or have had skin cancer
People who suffer from an increased risk ofskin cancer (e.g.
cases of skincancer in the family)
People among whose closest relatives a melanoma has occurred
People who are being medically treated for photosensitivity
People taking photosensitivity causing medicine
People with freckles and people who tend to develop freckles
People with more than 16 moles on theirbody (2 mm diameter or
larger)
People with atypical moles (atypical moles are, for example,
asymmetrical moleswith a diametergreater than5 mm, with vary-
ing pigmentation and irregular edges)
–Seek medical advice without fail if in doubt!
The following people may onlyuse the device after consultation with
their doctor:
People with chronic illnesses, in particular those related to the
skin
People with illnesses of the immune system /auto-immune dis-
eases
People with collagenosis (e. g. lupus erythematodes, sclero-
derma)
People suffering from rosacea (copper rose)
People with spider veins (e. g. couperose, Osler's disease, spider
nevi)
People with low bloodpressure, cardiovascular diseases
People suffering from venous diseases
People suffering from cancer
People with fresh woundsfollowing an operation or surgery

Safety instructions and warnings
10/72
People with tattoos or piercings which have not fully healed
Pregnant women
Should there be any doubt with regard to compatibility, despite no
known medical side effects, a test application of a maximum of 5
minutes should be initially carried out and the reactions observed. If
no adverse reactions are found after 48 hours, normal application may
be begun.
1.4.2 Important notes
All other people must observe the following instructions:
Danger of skin and eye injuries or skin diseases!
The skincan become sunburnt when exposed to excessive radia-
tion. Excessive,frequently repeated UV radiation exposure from
natural sunlight or UV devices can result in premature ageing of
the skin and an increased risk of skin tumours.
Particular cautionis advisable for individuals who are especially
sensitive to UV radiation, and when certain medicaments or cos-
metics are used. Seek medical advice withoutfail if in doubt!
Seek medicaladvice if any unexpected consequences, such as
itching, occurwithin 48 hours of the first tanning session.
Increasing tanning requires increased exposure time (= radiation
time) or after a certain degree of tanning has been achieved, in-
creased tanning is not possible. However, the radiation time may
not be extended as desired within the scope of the permissible ra-
diation doses! Therefore, only a certain level of final tanning,
which depends on the skin type, can be achieved without endan-
gering your health.
The tanning device may never be used when afilter panel is miss-
ing or damaged, or the timer is defective!
Behaviour before, during and after a sunbath:
During the tanning session no other people may remainin the
cabin, in particular no children.
Remove all jewellery (including piercings) before the tanning ses-
sion.
Remove cosmetics before tanning and do notuse sun screen
products.
Do not use any products intended to accelerate tanning.
UV light can cause irreversible skin or eye damage. The unpro-
tected eye can become inflamed on the surface, and in certain
cases the retina can be damaged by excessive radiation. Cata-
racts can form after numerous repeated tanning sessions.
Use the UV-impermeable protective goggles provided (order
no. 1027211-..). Contact lenses and sun glasses are no substi-
tutes for protective glasses.
Protect sensitive skin areas such as scars, tattoos andgenitals
before tanning.
Observe the recommended tanning times.
During a tanning session the quantity of radiation which results in
the skin reddening (MED, minimum erythema dose) may not be
exceeded. If reddened skin occurs around 16-24 hours after the
tanning session you may not use thetanning device again for one
week. After one week you can start againfrom thebeginning with
the first tanning session in accordance with the tanning table.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 11/72
The time between the first two sessions on the sunbedmust be at
least 48 hours! Do not take an additional sunbath on the same
day.
See a doctor ifstubbornswelling, sores or pigmented moles form
on the skin.
1.4.3 Skin type descriptions
DANGER!
Burns and long-term damage!
People with skin type I may not use the tanning de-
vice.
The following applies to people with skin types II, III
and IV:
–Observethe tanning times.
–Observethe safety instructions.
NOTE:
The tanning times are only valid for the lamp set spec-
ified on the lamp set sticker.
The tanning sessions should be at least 48 hours
apart.
The maximumdosage of 25 kJ/m² per year should
not be exceeded.
The maximumdosage is weighted according to
NMSC.1
Skin type I Skin type II Skin type III Skin type IV
Sensitive skin Light skin Normal skin Dark skin
Always/fre-
quently burns Usually burns Sometimes burns Rarely burns
Tolerates only a
small amount of
natural sun.
Tolerates approx.
10-20 min. of
natural sun.
Tolerates approx.
20-30 min. of
natural sun.
Tolerates approx.
40 min.
of natural sun.
1NMSC: Non Melanoma Skin Cancer

Safety instructions and warnings
12/72
1.4.4 Tanning times EN (UV type 2)
NOTICE:
People with skin type I should not use the device.
Observe the tanning times
Observe the national requirements!
The tanning dosage of 3 kJ/m² per programme of tanning sessions
should not be exceeded.
The maximumtanning time must not exceed 33.
The tanning sessions must be at least 48 hours apart.
The maximumtanning minutes per year should not exceed 833
minutes.
VITALITY 50
UV low-pressure lamps
TREND ADVANCED 160W R E5 1508550-..
Low-pressure lamps ERGOLINE TREND 8W E12 1512462-..
Number of tanning
sessions Skin type I Skin type II Skin type III Skin type IV
[min] [min] [min] [min]
1 – 5 5 5
2 – 11 11 11
3 – 13 13 13
4 – 13 13 13
5 – 16 16 16
6 – 16 16 16
7 – 20 20 20
8 – 22 22 22
9 – 25 25 25
10 –25 25 25
NOTICE:
According to standard EN 60335-2-27:2013 the tan-
ning table is not depending on skintypes.
Identical tanning times are valid for all skin types, with
the exception of skin type I.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 13/72
1.5 Safety instructions and warnings
1.5.1 Operator's obligations
As the operator you are responsible for providing clear operating,
cleaning andmaintenance instructions and ensuring the intended use
and the proper operation of the unit by means of training and instruc-
tion for the personnel.
Your operating instructionsmust enable the safe use and safe opera-
tion of the unitand take into account thecharacteristics and expertise
of your company and also the national work safety and environmental
protection regulations (within the European Union, the EU directive
89/391/EEC).
1.5.2 Personnel training
As the operator you are obliged to train your personnel and instruct
them in theestablished legal and accident preventionregulations. En-
sure that yourpersonnel have understood and observe these operat-
ing instructions. This applies in particular to the
information in 'Intended use' and 'Foreseeable misuse'
safety instructions in the 'Operation' chapter
operating instructions
cleaning and maintenance instructions
–Please makethe instructions and additional information from the
manufacturer available to thepersonnel at their workplace.
–Regularly checkyour personnel's safety consciousness and
awareness of the risks, taking into account your operating instruc-
tions.
–Please ensure that the cleaning intervals are complied with, in par-
ticular cleaning after every tanning session.
–Please ensure that your personnel provide your customers with
appropriate advice, in particular regarding tanning times, possible
risks and the operation of the device.
1.5.3 Scope of delivery
Information regarding the scope of delivery is contained inthe 'De-
scription' chapter on page 26.
1.5.4 Transport, assembly and setup
The deviceis delivered by a specialist company and assembled and
set up by the manufacturer's own service personnel or by an author-
ized service company.
As an operatoryou are responsible for complying withthe on-site ven-
tilation and electrical requirements at the setup location, see page 14.

Safety instructions and warnings
14/72
Assembly
DANGER!
Personal danger due to electric shock or burns!
–The assembly and electrical connection must
comply with the national regulations.
–The on-site electrical installation must be fitted
with an easily accessible all-pole isolating device
(master switch), complying with overvoltage cate-
gory III.This means that each pole must have a
contact opening width complying with the condi-
tions of overvoltage category IIIfor full isolation.
–If the connectionis established via a plug-in con-
nection thenthe connection system according to
EN 60309must be utilized.
–Assembly, installation, upgrading or repair of the
device may only be carried out by specially trained
and authorized personnel.
Information regarding the disassembly and assembly of the device is
available in the separate assembly instructions. These assembly in-
structions areintended solely for use by the manufacturer's service
personnel or byqualified specialists authorizedby themanufacturer.
Ventilation
WARNING!
Risk of overheating due to air flow problems!
Operating faults possible.
–
Do not change, obstruct or block the air inflow and
outflow area to the unit or makeany unauthorized
changes to theunit. The manufacturer shall bear
no liability for damage or injuries resulting from
such actions.
–Observe the ventilation system data.
–Do not set up and operate the device on the
transport pallet!
Data regarding the air supply and ventilation planning is available in
the planning manual (www.ergoline.de, available in English and Ger-
man). You can also obtain this data from yourdealership or the cus-
tomer service department (see page 2).

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 15/72
Setup location
WARNING!
Salty air! Contaminated air!
Device damagedue to corrosion of thehousing and
electrical components.
–Do not set up the unit at a swimming pool.
–Do not operate thedevice in locations with ag-
gressive environmental conditions (e.g. air con-
taining chlorine).
Damage to unit possible!
Where there are great differences in temperaturebe-
tween the transport route and the installationsite the
unit may notbe put into operation immediately after
being set up.
–Wait at least 2 hours befo
re connecting the unit to
the power supply.
Risk of overheating due to air flow problems!
Operating faults possible.
–
Do not change, obstruct or block the air inflow and
outflow area to the unit or makeany unauthorized
changes to theunit. The manufacturer shall bear
no liability for damage or injuries resulting from
such actions.
–Observe the ventilation system data.
–Do not set up and operate thedevice on the
transport pallet!
Environmental conditions
Optimum ambient temperature: Between +15 °Cand +32 °C
Storage temperature: Between -15 °C and +60 °C
The unitis not to be used outdoors.
Adaptation of theunit is required for operating altitudes greater than
2000 m above sea level in order to guarantee trouble-free operation.
The deviceis not suitable for operation in mobile facilities (ships,
buses, trains). Adaptation ofthe unit is required in order to guarantee
trouble-free operation when used in mobile facilities.
Please contact the Customer service department without fail before
putting the unit into operation - see page 2.

Safety instructions and warnings
16/72
1.5.5 Commissioning
DANGER!
Damaged mains power cable!
Danger to persons through electric shock or burns.
–Only the manufacturer or specialist companies
are permitted to replace the mains power cable.
Initial commissioning will be undertaken by themanufacturer's own
service personnel or by an authorized service company.The device
will be handed over ready for use.
If the devicehas not been used for a longer period of time,then it
must firstbe inspectedby our customer service department or by an-
other authorized company before beingput back into operation again.
The deviceis operated with an external time-control unit.
A time controlunit must be attached so that thedevice automatically
switches off at thelatest after <110 % of the selected running time
even if the controller fails. The device running timemust be secured
with a timer control that complieswith the standard EN 60335-2-27).
Dependent onthe localpower supply company, the devices can trans-
mit interference to thepower system of the building that impair the
audio-frequency remote control system used by the power supply
company. This can, for example, interfere with the function of night-
storage heaters.
If faults occurdue to the operation of the devices, thenthe operator is
responsible for the installation of an audio frequency blocking device
in the building electrical installation. Please contact your electrician.
The electrician is familiar with the technical connectionconditions of
your local utility company so that the audio-frequency blocking device
can be matched to thepower system of your power supply company.
1.5.6 Operation and maintenance
Error-free operation, maintenance and service are required in order to
ensure that thehealth and safety of the users is not endangered dur-
ing operation and to ensure that the device is in a fault-free operating
condition.
Please observe the information and recommendations provided in
these operating instructions.Please ensurethat the intervals for the
inspection, maintenance and service are complied with. Please ensure
that the lamps are replaced after thespecified usage time.
Unauthorized modifications and changes to the device and its control
unit are prohibited. Failureto complywith this invalidates the operat-
ing licence!
To avoid hazards, the device must not be used if the mains power ca-
ble is damaged. A damaged mains power cable must be replaced by
the manufacturer or their customer services, or by trained and quali-
fied specialist personnel.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 17/72
1.5.7 Decommissioning
The devicemust be disconnected from thepower supply inorder to
temporarily or permanently decommission it.
You must abide by the legal disposal requirements when permanently
decommissioning the device.
1.5.8 Storage
Store the devices in a dry location with a stable temperature. Once the
device has cooled off, pack it in plasticwrapping to protect it against
scratches.
Storage temperature: Between -15 °C and +60 °C
1.5.9 Disposal
Environmental regulations –
disposal of lamps and batteries
Lamps containfluorescent materials and other waste containingmer-
cury. Batteries contain heavy metal compounds.
Within the European Union the national implementation of the Waste
FrameworkDirective 2018/851/EG applies. According to the national
waste disposal laws and inaccordance with the municipal waste regu-
lations, proof must be provided of theproper disposal of lamps and
batteries.
Your local salesagencywill be happy to assist you withthe disposal
of lamps and batteries:
–Inform your local agency of the number of lamps and batteries by
telephone or in writing.
The agencywill then provide youwith the name of a freedelivery point
for your lamps orwill take care, in conjunction with a disposal com-
pany, of the collection and proper disposal of the lamps. This service
is available for a fee. Outside Germany, the respective national legisla-
tion applies. Please contactyour local sales agency.
Packaging
All packaging consists of100 % recyclable materials. Packaging
brought into circulation by the JK Corporate Group that is no longerre-
quired can be returned to the JKCorporate Group. Your partner
agency or dealer will be happy to advise.
Disposal of old units
The unithas been manufactured using recyclable materials. The JK
Corporate Group will provide you with information on the content or
potential hazards of the materials used.
The manufacturer is obliged to take back and disposeof certain elec-
trical and electronic components inaccordance with the 2012/19/EC
Directive.

Safety instructions and warnings
18/72
The components and units are labelledwith the following symbol:
The unitwill, if requested, be properly disposed of by the JK Corporate
Group. This service is available freeof charge. Your partner agency or
dealer will behappy to advise.
Registration numbers
Companies within the JKCorporate Group are registered as manufac-
turers in Germany and accept all obligations inrespect of the German
Electrical and Electronic Equipment Act.
Registry number JK-International GmbH, division JK-Licht GmbH
(lamps): WEEE-DE 61515020
Registry number JK-Products GmbH (Devices): WEEE-DE 62655951
1.5.10 Directives
See the included EC Declaration of Conformity.
1.5.11 Export
We emphasize that these units are only intended for the European
market andmust not be exported to oroperated in other countries e.g.
the USA or Canada! The manufacturer does not accept any liability in
the event of non-observance! We explicitly emphasize that non-com-
pliance may result in high liability risks for the exporter and/or the op-
erator.

Safety instructions and warnings
02/2023 1029445-00 Operating instructions – 19/72
1.5.12 AUX (music)
If an MP3 player or a smartphone is used privately during the applica-
tion, then this does not constitute a public performancein the sense
of copyrightlaw, so that no reporting or fee obligation exists on the
part of the studio operator towards the organisation responsible for is-
suing the commercial performance rights.
For the public use of MP3 music files, thesame legislation applies as
for all other music sources: As a studio operator/studio owner, you
may onlyplay original audio CDs, MCs, audio DVDs etc., on your prem-
ises and/orplay music via the 'MP3-music modules' which are pro-
vided in the devices from JK-International GmbH if you haveacquired
the necessary stage rights. You can acquire these from theorganisa-
tion responsiblefor issuing commercialperformancerights inyour
country (inGermany: GEMA/GVL).
Copy-protected audio CDs, MCs, audioDVDs etc., as well as titles con-
tained on these media, may not be converted to MP3 format and/or
saved on HDD, audio CDs, MCs, audio DVDs etc.,if software is used to
do this, whichdisables or circumvents the copy-protection contained
on the media.
You must be ready at any timeto prove your granting of stage rights
by presentation of the appropriate stage rights certificate when re-
quested by a representativeor another controlling bodyof the respon-
sible organisation.
As long as you observe all the listed instructions and have acquired
the necessary rights for use of the 'MP3-music module', you may con-
vert your original audio CDs, MCs, audioDVDs etc. into the MP3 for-
mat requiredby the player. Only one copy (duplicate or MP3 format
conversion) of lawfully acquired audio CDs, MCs, audioDVDs etc. may
be made. The source media (original media) must be retained and
may not be used simultaneously.
Further details can be found in the information brochure 'Audio Guide'
available on the Internet at http://www.jk-globalservice.de.
NOTE:
Pre-recorded SD cards which aredelivered as acces-
sories for a JKaudio system are also subject to pay-
ment obligation for commercial usage.
1.5.13 Technical modifications
The devicehas been constructed in accordance with thecurrent state
of the art and the applicable safety regulations. The illustrations and
specifications in these operation instructions aresubject to technical
modifications which are required in order to improve the device.
Unauthorized modifications and changes to the device and its control
unit are prohibited. Failureto complywith this invalidates the EC con-
formity!
Please use only original spare parts. Failureto complywith this invali-
dates the EC conformity!

Safety instructions and warnings
20/72
1.6 Signs and stickers on the unit
Danger area warning signs and important information about compo-
nents are attached to the unit.The signs shown beloware examples.
Ensure that the warning signs are always clearly recognisable and leg-
ible. Anymissing warning signs or stickers must be replaced.