ERNITEC SX User manual

Ernitec SX camera Quick Guide
The Quick Guide is for quick installing and connecting the Full HD Multiple Streaming IP Camera. For details, please
refer to the IP Camera’s User Manual.
Camera Rear Panel
DC 12V/ AC 24V/ PoE
C/CS Mount Lens Motorized Lens
Definition
Remarks
LINE OUT & LINE IN / MIC IN
Two-way audio transmission
Power LED
Power connection indication (green light).
Reset button
Reset to factory default
AUTO IRIS connector
Auto iris lens connector
NETWORK (with PoE)
RJ-45 connector
Network LEDs
Network connection and activity indication
I/O
1
Output＋
5
GND
2
Output－
6
D－
3
Input＋
7
D＋
4
Input－
VIDEO (BNC connector)
For video output
Micro SD Card slot
For video and snapshots storage
AC 24V/DC 12V connector
(AC 24V Model)
＋
AC 24V: Power-1
DC 12V: Power
LINE
OUT
LINE IN
MIC IN
NETWORK
AUTO
IRIS
PoE
1 2 3 4 I/O
DC VIDEO
AC 24V
DC 12V
AC 24V: Earth GND
DC 12V: Reserved
－
AC 24V: Power-2
DC 12V: GND
Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need to mount the supplied C/CSmount adapter
to the camera. Then attach the lens onto the C/CS mount adapter.
IP Camera Installation
Please follow the instructions below to complete IPCamera installation.
Power up the Camera
To power up the IP Camera, please plug the camera’s DC 12V/ AC 24V cable into the power outlet. Alternatively,
connect the Ethernet cable to the camera’s PoE port and plug the other end of the cable into a PoE switch.
NOTE: If using PoE, make sure Power Sourcing Equipment (PSE) is in use in the network.
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet cable to the RJ-45 connector of the IP Camera,and the other end of the cable
to the network switch or PC.
NOTE: In some cases, you may need to use an Ethernet crossover cable when connecting the IP Camera
directly to the PC.
NOTE: Check the status of the link indicator and activity indicator LEDs; if the LEDs are unlit, please check
LAN connection.
Green Link Light indicates good network connection.
OrangeActivity Light flashes for network activity indication.
Before Login to the IP Camera
A client program will be automatically installed on your PC when connecting to the IP Camera. Beforelogging in to the
IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the IP Camera’s user manual.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then Click <Internet Options>.
Step 3: Click the <Security> tab and select “Internet”,
and click <Custom level> to change ActiveX
settings.
Step 4: Set “ActiveX controls and plug-ins”items to
<Prompt> or <Enable>.
Step 1: Start the IE.
Step 2: Select <Tools> from the main menu of the
browser. Then Click <Internet Options>.
Step 3: Click the <Security> tab and select “Internet.”
Step 4: Down the page, press “Default Level”and click
“OK”to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP Camera
IP Camera Login
The IP Camera’s default IP address is: 192.168.0.250. Therefore, to access the IP Camera for the first time, set the
PC’s IP address as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID & Password
Key in the IP Camera’s IP address in the URL bar of the Web browser window and press “Enter.”
Enter the default user name (Admin) and password (1234) in the prompt request dialogue. Note that user name is
case sensitive.
Install the ActiveX Control
After connecting to the IP Camera, the request for installing theActiveX control will appear just below the URL bar.
Right Click on the information bar, and press “InstallActiveX Control…” to permitActiveX control installation.
AUTO
IRIS
1 2 3 4
I/O
NETWORK
DC12V
LINE LINE IN
MIC IN
OUT
VIDEO
DC
RESET
Reset
Button
Power
LED
Network LEDs
Reset
Button
Power
LED
Network LEDs

V1.5.09.12
In the pop-up security warning window, click “Install”to start downloading DC Viewer software on the PC.
Press “Finish”after DC Viewer installation is complete.
Browser-based Viewer
The main page of the IP Camera user interface is shown as the figure below. Please note that function buttons will
vary depending on the camera model.
Ernitec SX Camera
Quick Guide