ESCALADE Harvard Arcade Games M01462W User manual

1 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
1-888-996-2729
FAX: [phone]
[e-mail]
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706
When contacting Escalade Sports please provide your model number, date code (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.
Your Model Number:
Please have your model number when inquiring about parts.
M01462W
Date Code:
2-M01462W- -ZG
All Rights Reserved
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
TWO (2) ADULTS ARE REQUIRED TO ASSEMBLE
THIS BASKETBALL SHOOTOUT
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS BASKETBALL
SHOOTOUT TOGETHER.
2 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
Tools Needed:
Wrenches T1 and T2 (Included with the Hardware Kit)
Philips Screwdriver
Adjustable Wrench or Socket Set is helpful but not required.
Make sure you understand the following tips before you begin to assemble your
basketball shootout.
1.This is an electrically operated product. It is intended for INDOOR use ONLY.
2.This product is not designed to be used in a garage or on a patio, sunlight may effect
the infrared sensors and the unit will not perform correctly.
3.Tighten hardware as instructed.
4.Do not over tighten hardware,as you could crush the tubing.
5.Some drawings or images in this manual may not look exactly like your product.
6.To prevent damage to the electronics, do not place this unit any closer than six inches
from the wall.
!

H1 - M6 x 55mm
Allen Head Bolt (4)
H4 - M5 x 20mm
Allen Head Bolt (4)
H5 - M3 x 10mm
Phillips Round Head
Screw (8)
H6 - 12mm
Flat Washer (24)
H7 - 9mmFlat Washer (8) H8 - M6 Locknut (20) H9 - M5 Locknut (4)
H2 - M6 x 46mm
Allen Head Bolt (8)
H3 - M6 x 20mm
Allen Head Bolt (8)
3 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
T1 - Allen Wrench (1) T2 - Wrench (1)
(To Scale)
(Not to Scale) (Not to Scale)

P1 - Front U Tube (1) P2 - Base Tube (2)
P3 - Front Support Tube (2)
P5 - Front Connector Tube (2)
P7 - Middle Connector Tube (2)
P8 - Cross Tube (2)
P9 - Back Tube (2) P10 - Top Tube (2)
P6 - Back Connector Tube (2)
P4 - Back Support Tube (2)
4 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All RIghts Reserved.

P16 - Ramp Net (1)
P11 - Backboard (1) P12 - Rim (2)
P15 - Rim Net (2)
P14 - Electronic Scorer
with Sensors and
Multi Color Wires (1)
OR
P14A - Electronic Scorer
with Sensors and
Solid Color Wires (1)
P13 - Rim Support Plate (2)
A2 - Adapter (1) A3 - Basketball (4)
Parts Identifier
5 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
A1- Air Pump w/Needle (1)
Accesory Identifier
!
WARNING:
CHOKING HAZARD
Small parts.
Not for children under 3 yrs.

1. Snap Front Support Tubes P3 into Base Tube P2 using spring locks.
2. Snap Front U-Tube P1 into Front Support Tube P3 using spring locks.
P3
P3
Figure 1
P3
P2
P2
P1
6 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved.
PARTS REQUIRED:
2 pcs - P3 Front Support Tube 1 pc - P2 Base Tube
Figure 2
P3
PART REQUIRED:
1 pc - P1 U-Tube
Spring Lock
Spring Lock

3. Snap Back Support Tubes P4 into Base Tube P2 using spring locks.
4. Snap Support Tubes P9 into Back Support Tube P4 using spring locks.
P4
P4
P2
P9
7 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
PARTS REQUIRED:
1 pc - P2 Base Tube 2 pcs - P4 Back Support Tube
Figure 3
Spring Lock
P9
P4
P4
P2
PARTS REQUIRED:
2 pcs - P9 Support Tube
Figure 4
Spring Lock
All Rights Reserved.

5. Attach Cross Tube P8 and Back Connector Tube P6 to Back Tube P9 using Allen Head
Bolts H2, Flat Washers H6 and Locknuts H8 as shown in Detail A. Use Wrench T2 to
tighten nuts. Repeat this step for other side.
6. Slide Middle Connector Tube P7 into Back Connector Tube P6 using spring lock as
shown in Detail B. Next, Slide Middle Connector Tube P7 into Front Connector Tube P5
using spring lock shown in Detail C. Repeat this step for other side.
7. Install Front Connector Tube P5 onto Front U-Tube P1 using Allen Head Bolt H2, Flat
Washers H6 and Locknut H8 as shown in Detail D. Use T2 Wrench to tighten nut.
Repeat this step for other side.
P5
P6
8 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
Detail C
H2
P5
P7
Spring Lock
Detail B
Spring Lock
H6
H8
Figure 5
PARTS REQUIRED:
6 pcs - H2 Allen Head Bolt 2 pcs - P6 Back Connector Tube
12 pcs - H6 Flat Washer 2 pcs - P7 Middle ConnectorTube
6 pcs - H8 Locknut 1 pc - P8 Cross Tube
2 pcs - P5 Front Connector Tube 1 pc - T1 Allen Wrench
1 pc - T2 Wrench
All Rights Reserved.
Detail A
H2
H6
P8
H6
H8
P9
P8
P6
P1
Detail D
P9
P6
P5
P7

8. Attach two rims P12 to the backboard P11 using Allen Head Bolts H3, Rim
Support Plate P13 and Locknuts H8 as shown in Figure 6. The Support
Plate P13 attaches to the back of backboard P11 as shown. Place Nets
P15 on each Rim P12.
9 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
PARTS REQUIRED:
8 pcs - H3 Allen Head Bolt 2 pcs - P13 Rim Support Plate
8 pcs - H8 Locknut 2 pcs - P15 Rim Net
1 pcs - P11 Backboard 1 pc - T1 Allen Wrench
2 pc - P12 Rim 1 pc - T2 Wrench
Figure 6
P11(Back Side) H3
P12
P15
P13
H8
All Rights Reserved.
Note: Match hole pattern on the Backboard P11 with the Rim P12
and Rim Support Plate P13.

9. Important: If P14 Electronic Scorer has MULTI color sensor wires see Figure 7A.
If P14 Electronic Scorer has SOLID color sensor wires see Figure 7B.
Peel the protective coating from electronic scorer P14 / P14A and attach to the back
of Backboard P11 using Allen Head Bolts H4, Flat Washers H7, and Locknuts H9
as shown in Figure 7. Attach each sensor to the backboard with 2 Screws H5 as
shown below.
10 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
PARTS REQUIRED:
4 pcs - H4 Allen Head Bolt 1 pc - P14 Electronic Scorer
8 pcs - H5 Phillips Round Head Screw with Sensors and
8 pcs - H7 Flat Washer Multi Color Wires, OR
4 pcs - H9 Locknut 1 pc - P14A Electronic Scorer
1 pc - T1 Allen Wrench with Sensors and
1 pc - T2 Wrench Solid Color Wires
Figure 7
P14 / P14A
P11 (Back Side) H4
H7
H9 H7
Black/Gray
Wire
White/Gray
Wire
Brown/Black
Wire
Gray/Black
Wire
H5
All Rights Reserved.
Black Wire
Brown
Wire
Grey
Wire
H5
Figure 7B
White
Wire
P14 - Electronic Scorer with
Multi Color Sensor Wire
P14A - Electronic Scorer with
Solid Color Sensor Wire
Figure 7A

10. Slide elastic straps and sleeve of P16 Ramp Net onto P10 Top Tubes as
shown in Figure 8.
11 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
11. Insert Top Tubes P10 into Back Tubes P9 as shown in Figure 9.
PARTS REQUIRED:
2 pcs - P10 Top Tube
2 pcs - P16 Ramp Net
P10
P10
P16
P16
P10
P10
P9
P9
P16 P16
Figure 9
Figure 8
All Rights Reserved.

12. Attach the backboard to the frame. With the help of another adult start at the top hole, place
a H6 Washer on a H1 Bolt, pass the bolt through grommet of net and P10 Top Tube and
the backboard. Place a H6 Washer on the bolt and secure with a H8 Locknut as shown in
Detail E. Repeat for other side. At each bottom hole of the backboard, repeat the
above procedure except bring the ramp up behind the P8 Cross Tube, place the ramp tabs
over H1 Bolt and attach with H6 Washer and H8 Locknut as shown in Detail F.
13. Slide Cross Tube P8 through sleeve on the front of the ramp net, attach P8 Tube to Front
Connector Tube P5 and Front U-Tube P1 with Allen Head Bolts H2, Flat Washers H6 and
Locknuts H8 as shown in Detail G. Use T2 Wrench to tighten nuts.
14. Secure the Velcro Straps around the tubes.
8P
12 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
Figure 10
PARTS REQUIRED:
4 pcs - H1 M6 x 55mm Allen Head Bolt 1 pc - P8 Front Cross Tube
2 pcs - H2 M6 x 46mm Allen Head Bolt 1 pc - T1 Allen Wrench
12 pcs - H6 Flat Washer 1 pc - T2 Wrench
6 pcs - H8 Locknut
All Rights Reserved.
P8 P5
H6
H2
H8
P1
Detail G
H1 H6
H6
P10
H8
P11
Detail E
PLACE RAMP NET P16
BEHIND TUBE P8
P8
!
H1
H6
H6
P10
Detail F
P11
H8
Ramp Tab on
backside of
P11 Backboard.
Note: Backboard on
backside of P10 Top
Tubes.

13 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
Plug the adapter into a suitable 120v household outlet and into the back of the scoring unit.
Each player has 30 seconds to make as many baskets as they can.During the first 20 seconds
each shot counts as 2 points. During the last 10 seconds each shot counts as 3 points.
Press the “RESET” button at the back of Electronic Scorer to start a new game.
NOTE:
You may also need to move the unit if you cannot get it to score correctly.
Sunlight or halogen lighting will have an effect on the sensors causing them to not
function properly. If the unit is relocated at a later date, the test procedure must be
repeated as explained below.
NOTE:
If you feel the performance of the electronic scoring sensors still do not function
properly, please follow these steps:
Step1: Push the “Play/Test” switch to “Test”.
Step2: To begin with the “Test” mode, the scorer should have “88” “88” “88” showing on the
electronic scoring display. Place a ball slowly at the top of the rim to test the top scoring sensor.
The top electronics sensor will read the ball and the electronic scorer should display changes
from “88” to “18” and making a “buzzing sound”. Then slowly place the ball at the bottom
of the rim to test the bottom electronic sensor. The bottom sensor will read the ball and the
electronic scorer should display changes from “88” to “81” and making a “buzzing sound”.
You have now calibrated the scoring sensors for the present light conditions.
If light conditions change, this same recalibration of the electronic scoring sensors may be
required for proper operation of the electronics scoring sensors.
Step3: Push the “Test” mode switch to “Play” to start your game.
NOTE:
There may be some types of shots that will not score every time.If two balls pass through
the rim at the same time it will not register both shots,The unit may also register a shot
when the ball passes quickly in front of the rim. These situations are normal.
ADJUSTMENT AND USE OF YOUR BASKETBALL SHOOTOUT
CARE AND USE OF YOUR
BASKETBALL SHOOTOUT
Congratulations! You have now assembled your Basketball Shootout.
Please note the Care and Use instructions below.
1. Plug the adapter into a suitable 120v AC household outlet.
2. This product is intended for INDOOR use only.
3. DO NOT sit,climb or lean on the unit.
4. DO NOT drag the unit when moving it,This will damage the legs.
All Right Reserved.

PRODUCT PARTS LIST
Part# Description QtyPart# Description Qty
01462ZGH1 M6 x 55mm
Allen Head Bolt 4
01462ZGH2 M6 x 46mm
Allen Head Bolt 8
01462ZGH3 M6 x 20mm
Allen Head Bolt 8
01462ZGH4 M5 x 20mm
Allen Head Bolt 4
01462ZGH5 M3 x 10mm Phillips
Round Head Screw 8
01462ZGH6 12mm Flat Washer 24
01462ZGH7 9mm Flat Washer 8
01462ZGH8 M6 Locknut 20
01462ZGH9 M5 Locknut 4
01462ZGT1 Allen Wrench 1
01462ZGT2 Wrench 1
01462ZGP1 Front U-Tube 1
01462ZGP2 Base Tube 2
01462ZGP3 Front Support Tube 2
01462ZGP4 Back Support Tube 2
01462ZGP5 Front Connector Tube 2
M01462W
14 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved.
01462ZGP6 Back Connector Tube 2
01462ZGP7 Middle Connector Tube 2
01462ZGP8 Cross Tube 2
01462ZGP9 Back Tube 2
01462ZGP10 Top Tube 2
01462ZGP11 Backboard 1
01462ZGP12 Rim 2
01462ZGP13 Rim Support Plate 2
01462ZGP14 Electronic Scorer
with Sensors and
Multi Color Wires 1
01462ZGP14A Electronic Scorer
with Sensors and
Solid Color Wires 1
01462ZGP15 Rim Net 2
01462ZGP16 Ramp Net 1
01462ZGA1 Air Pump 1
01462ZGA2 Adapter 1
01462ZGA3 Basketball 4
01462ZGK1 Hardware Kit 1
01462ZGM1 Manual 1

15 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
EDALACSEynafoesahcrupremusnoclanigiroehtotsdnetxeytnarrawremusnocsihT
.)"tcudorP"ehtsaderreferretfaniereh(tcudorPSTROPS
:NOITARUDYTNARRAW -epafoesahcrupremusnoclanigiroehtotdetnarrawsitcudorPsihT
.esahcruplanigiroehtmorfsyad09fodoir
:EGAREVOCYTNARRAW resahcruPremusnoClanigiroehtotstnarrawSTROPSEDALACSE
desunehwpihsnamkrowdnalairetamnistcefedmorfeerfsierutcafunamstifotcudorPynatah
EHTF
IDIOVSIYTNARRAWSIHT.snoitidnocdnaesulamronrednuesoprupdednetniehtro
,ECNEGILGEN,ESUELBANOSAERNU,TNEDICCAYBDEGAMADNEEBSAHTCUDORP
-DORPEHTHTIWDEDIVORPSNOITCURTSNIWOLLOFOTERULIAF,ECIVRESREPORPM
-NAMKROWDNALAIRETAMNISTCEFEDFOTUOGNISIRATONSESUACREHTOROTCU
.PIHS
:ECNAMROFREPYTNARRAW EDALACSE,doirepytnarrawyad09evobaehtgniruD
,foerehttnenopmocro,tcudorPdna,ledomelbarapmocahtiwecalperroriaperllahsSTROPS
llahsnoit
animaxeruohcihwdna,eracreporpdnaesulamronrednuevitcefedevorpyamhcihw
Customer Service Dept.ruotcatnocesaelp,evitcefedsuhtebotnoitcafsitasruootesolcsid
/9272-699-888-1 Customer Service Dept.
:tasuetirWrO
60774NI,ellivsnavE,988xoB.O.P-.cnI,stropS®edalacsE
Customer Service Dept.:nttA
:tasuliam-ErO
moc.stropsedalacse@
-nifotnemecalperroriaperhcusrofedameblliwegrahconstnemeriuqergnippihsnahtrehtO
rofder
usnisitcudorPehttahtsdnemmocerylgnortsSTROPSEDALACSE.stcudorPytnarraw
.gni
liamo
troirpeulav
:SREMIALCSIDYTNARRAW FOTUOGNISIRASEITNARRAWDEILPMIYNA
FOSEITNARRAWDEILPMIEHTOTDETIMILTONTUBGNIDULCNI,ELASSIHT
-MILERA,ESOP
RUPRALUCITRAPAROFSSE
NTIFDNAYTILIBATNAHCREM
STROPSEDALACSE.DOIREPYAD09EVOBAEHTOTNOITARUDNIDET
REHTOROTCUDORPEHTFOESUFOSSOLROFELBAILEBTONLLAHS
-NISEGAMADROSESNEPXE,STSOCLATNEDICNIROLAITNEUQESNOC
.ESUREHTOYNAFOREMUSNOCEHTYBDERRUC
rolaitneuqesnocroseitnarrawdeilpmifonoitatimilronoisulcxeehtwollatonodsetatsemoS
.uoyotylppatonyamsnoisulcxerosnoitatimilevobaehtos,segamadlatnedicn
:SEIDEMERLAGEL rehtoevahoslayamuoydnasthgirlagelcificepsuoysevigytnarrawsihT
.etatsotetatsmorfyravyamhcihwsthgir
YTNARRAWDETIMILYAD09
gameroom