ESCALADE SilverBack B5455 User manual

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
I N S T A L L A T I O N I N S T R U C T I O N S
2021 Escalade Sports
B A L L H O L D E R MODEL NO.
B5455
2L-7952-00
1. Read this manual carefully before starting assembly. Read each step completely
before beginning each step.
2. Do not tighten until instructed to do so. If parts are tightened too soon, parts
may not easily fit together.
3. Save these instructions and your proof of purchase (receipt) in the event that
the manufacturer has to be contacted for replacement parts.
P R E - A S S E M B L Y T I P S
Contact Escalade Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
1-800-USA-GOAL
Please Do Not Return This Product To The Store!
®
Escalade Sports
817 Maxwell Ave.
Evansville, 47711IN
Physical Location:
PO Box 889
Evansville, 47706 IN
Mailing Address: (Correspondence Only)
2
3
TOOLS NEEDED FOR ASSEMBLY:
Phillips Screw driver
Cordless Drill
5/6” Socket driver bit
P A R T S L I S T ( N O T A C T U A L S I Z E ) H A R D W A R E N E E D E D ( A C T U A L S I Z E )
1
BASE
3M-9137-00
QTY. 1
GRIPPER FINGER
3M-9138-00
QTY. 4
MOUNTING BRACKET
3M-9139-00
(QTY. 1)
#8 X .375 Phillips Head
Trilobular Screw
1B-7225-00
QTY. 10
4
#10 X 1.0 Phillips screw
1B-7226-00
QTY. 1
TAPE PATCH
QTY. 1
1M-6289-00
6
5
#10 X 1.125 Self Drilling Screw
1B-6821-00
QTY. 1
7

2
BACK VIEW
FIGURE 1
1. Assemble four Gripper Fingers (#2) to Base
(#1) as shown in Figure 1 & Back View.
1
2
4
Phillips
TOOL NEEDED
#8 X .375 Phillips Head
Trilobular Screw
1B-7225-00
QTY. 8
4
HARDWARE NEEDED
#8 X .375 Phillips Head
Trilobular Screw
1B-7225-00
QTY. 2
4
#10 X 1.125 Self Drilling Screw
1B-6821-00
QTY. 1
7
NOTE: Prepare hardware and tools below to be used for page 3 assembly steps.
TOOLS REQUIRED
Cordless Drill
5/6” Socket
driver bit
HARDWARE NEEDED
Phillips

FIGURE 2
DETAIL B
3
If installing to the back of a basketball pole continue onto Step 2 on
this page. If mounting to a Wall skip this page and continue on page 4.
2. Clean the flat side of the mounting bracket surface with alcohol. Peel
one side of the mounting Tape (#6) and adhere the to the Flat part of
the Mounting Bracket (#2)as shown in Detail A.
3. Clean mounting location surface with alcohol. Peel the other side of
the mounting tape and adhere mounting location. See Detail B.
4. Install self-drilling screw using 5/16” Hex Socket Driver and cordless drill.
When 5/16” Hex Driver makes contact with Mounting Bracket finish
tightening screw with Philips Screwdriver. Do not over tighten. See Detail C.
3
Back of pole
NOTE: Holes must be in the
Vertical position as shown
before adhering to pole.
NOTE: Holes in the Mounting Bracket (#3) must be in the Vertical position as
shown in Detail B before adhering Mounting Bracket to the pole.
6. When the Mounting Bracket is completely adhered to the pole, attach the
Ball holder assembly with two Screws (#4). See Figure 2.
DETAIL A
6
Flat Surface
Peel
3
3
4NOTE: Tighten
until secure, but
DO NOT OVER-
TIGHTEN.
DETAIL C
7
5. If self-drilling screw is not used Mounting Bracket must be clamped in place
for 24 hours before attaching Ball Holder.

DETAIL A
5
3
Anchor
NOTE: Holes must be in the
Vertical position as shown
before screwing to wall anchor.
Flat Surface
FIGURE 3
3
4NOTE: Tighten
until secure, but
DO NOT OVER-
TIGHTEN.
4
Phillips
TOOL NEEDED
If installing to the back of a basketball pole go back to Step
2 on page 3. If mounting to a Wall continue on this page.
3. Attach Mounting Bracket (#3) to the wall using Screw (#5) as shown
in Detail A. The flat surface of the bracket must be facing the wall.
NOTE: Holes in the Mounting Bracket (#3) must be in the Vertical
position as shown in Detail A before attaching Mounting Bracket to
the wall.
If you are mounting the Ball holder to a wall you will need to
purchase either a drywall or masonry wall mounting kit
depending on the wall you have. The kit will need an anchor
for a #10 phillips head screw.
NOTE:
2. Follow the manufacturer’s instructions on installing the anchor
and then proceed to step 3.
#8 X .375 Phillips Head
Trilobular Screw
1B-7225-00
QTY. 2
4
HARDWARE NEEDED
#10 X 1.0 Phillips screw
1B-7226-00
QTY. 1
5
4. Attach the Ball holder assembly to the Mounting Bracket with two
Screws (#4). See Figure 3.