ESCALADE GOALIATH B7006CF User manual

MODEL NO.
GB54ig2.0
BASKETBALLSYSTEM
2L-7639-01
Escalade®Sports products may be manufactured and/or licensed under the following patents:
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128, 7244046
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2017 Escalade Sports
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly of your basketball system easier, use the Hardware Identifier on page 4
to identify and sort all fasteners. Check all cartons for kits. All hardware is not located
in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
O W N E R ' S M A N U A L
B7006CF
©
Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: Toll – Free!1-888-872-4625
Fax: [phone] Toll – Free!
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at:
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®SPORTS PRODUCT INFORMATION
5.
An electric screwdriver is helpful in assembly. However, please set at low torque and use caution
because you could overtighten the hardware and strip the screws.
6.
Save this instruction and your proof of purchase (receipt) in the event that the manufacturer
has to be contacted for replacement parts.
ITEMS NEEDED (not included)
9-
1-
1-
1-
1-
1-
6-
2-
1-
1-
1-
1-
1-
1-
1-
50 lbs bags of concrete
Post hole digger (optional)
Wheel barrow
Garden hose
Level
Tape Measure
2X4’s
50 lbs sand bags
Standard masonry block
9/16”, 3/4” & adjustable wrench
Cordless drill & 9/64” drill bit
5/16” socket driver (for cordless drill)
Pair of Safety Glasses
Phillips Screwdriver
Ladder
www.escaladesports.com

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow these rules for safe operation of the system.
SAFETY INSTRUCTIONS
7
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY
R E S U LT I N S E R I O U S I N J U RY A N D /O R
PROPERTY DAMAGE.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
!Do not dunk on this unit
!Do not hang from any part of the unit, including
the backboard, rim, support braces, or net.
!Do not slide, climb, or play on pole.
!Keep organic material away from pole base.
Grass, litter, etc. could cause corrosion and /or
deterioration.
!Check pole system for signs of corrosion
(rust, pitting, chipping). Remove rust and/or
loose paint completely and repaint with
exterior enamel paint. If rust has penetrated
through the steel anywhere, replace pole
immediately.
!Check system before each use for proper
ballast, loose hardware, excessive wear, and
signs of corrosion and repair before using.
!During play, use extreme caution to keep
players face away from the backboard, rim,
and net. Serious injury could occur if
teeth/face come in contact with backboard,
rim, or net.
!Wear a mouth guard when playing to avoid
dental injuries.
!When adjusting height, keep hands and
fingers away from moving parts.
!During play, do not wear jewelry (rings,
watches, necklaces, etc.). Objects may
entangle in net.
!Do not allow children to adjust system.
!Check system before each use for instability.
!Never play on damaged equipment. 4L-7609-00
2

3
(Affixed to Bottom Post)
FAILURE TO FULLY ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
Bottom of upper pole must cover the
above orange portion of this sticker
(6” mark).
Le bas du poteau supérieur doit
couvrir la partie orange ci-dessus de
cet autocollant (marque à 6 po).
WARNING
!
BACKSIDE
4L-8151-30
AVERTISSEMENT
!
LE FAIT DE NE PAS ENGAGER EN-
TIÈREMENT LE BAS DU POTEAU SU-
PÉRIEUR JUSQU'À LA MARQUE DE 6
PO SUR L'ÉTIQUETTE DE CE PO-
TEAU INFÉRIEUR PEUT ENTRAÎNER
L'EFFONDREMENT DE VOTRE UNITÉ
ET CAUSER DES BLESSURES
ARRIÈRE

3/8-16”
Lock Nut
(14 pieces)
1/2”-13
Lock Nut
(1 piece)
3/8-16 X 1-3/4”
Hex Bolt
(4 pieces)
3/8-16 X 5”
Hex Bolt
(2 pieces)
3/8-16 X 7”
Hex Bolt
(2 pieces)
3/8-16 X 1-3/4”
Carriage Bolt
(4 pieces)
1/2-13 X 1-1/2”
Hex Bolt
(1 pieces)
3/8-16 X 6-1/2”
Hex Bolt
(2 pieces)
Pivot Tube
(1 Piece)
1/2” Flat Washer
(2 Pieces)
Stop Spacer (Pieces)
3/8”
Flat Washer
(18 Pieces)
3/8”
Flat Washer for Rim
(4 Pieces)
Pull Pin
(1 Piece)
1” X 1/4” Spacer
(2 Pieces)
#10 X 1”
Self Tapping Screw
(10 Pieces)
1-1/4” Dia.
Plastic Washer
(8 Pieces)
#8 X 1/2”
Thread Forming
Screw
(4 Pieces)
Note: Check all cartons for hardware. All hardware is not packed in one kit.
BASKETBALL SYSTEM’S HARDWARE IDENTIFIER
4

Figure 1
INSTALLATION TIMELINE
PART 1
Day 1. Post assembly, pour concrete, set post and
Day 2. Allow concrete to cure.
PART 2
Day 3. Complete Goaliath® assembly instructions. (Requires
3-4 adults)
Note: For best results with less vibration, your system
should be independent of court. If pouring concrete for
both at same time, add an expansion joint in between.
2.
1. Determine the location of the hole.
The proper location is as close to the
court without making contact, as
shown in Figure 1. This,
however, is a general rule.
If you need to locate the
hole in a location other than this, use
the following dimensions as a guide.
Overhang when adjusted to 305cm (10ft.) = 49cm
2. Vertical main post assembly is a two part process.
1. Prior to pole installation and goal assembly, call utility services for location of underground utility lines before you dig.
POST INSTALLATION INSTRUCTIONS (Day 1)
81cm
Court
Hole
Court Level
Court
Top View
Hole must be close to
the Court without
making contact.
Dig a round hole 81cm deep and 41cm in diameter
at the top and 51cm in diameter at the bottom of the
hole. If you live in an area where frost heaves may
pose a problem, consult your local building inspector
to determine the proper hole depth. See Figure 1.
3. Place and center a masonry block in the bottom of the
hole so there is exactly 40.6cm (16”) from the playing
surface to the top of the masonry block. See Figure 2.
Figure 2
Hole
Masonry
Block
Allow concrete to cure.
MINIMUM
REAR
CLEARANCE
REQUIRED
Note: When digging hole, if you hit rock
and cannot dig through contact a contractor.
Note: Minimum of 18” rear clearance is required behind pole.
ITEMS NEEDED (not included)
9-
1-
1-
1-
1-
1-
6-
2-
1-
1-
1-
1-
1-
1-
1-
50 lbs bags of concrete
Post hole digger (optional)
Wheel barrow
Garden hose
Level
Tape Measure
2X4’s
50 lbs sand bags
Standard masonry block
9/16”, 3/4” & adjustable wrench
Cordless drill & 9/64” drill bit
5/16” socket driver (for cordless drill)
Pair of Safety Glasses
Phillips Screwdriver
Ladder
32"
41cm (16”) Diameter
51 cm (20”) Diameter
40,6cm
16”
46cm (18”)
5
Before digging hole for your system, check for
buried power, gas, water, and telecommunication
lines! Failure to do so could result in serious or fatal
injury! Contact your local utility company if unsure.

INSTRUCTIONS
POST ASSEMBLY
1.
2. Align the upper pole (#3) with the bottom pole (#2) as
shown in Figure 3 and slide them together. While
maintaining control of the pole assembly stand poles
up STRAIGHT on a piece of MDF or plywood, lift
poles up by bottom pole below the 6” mark shown
on sticker and slam down the bottom pole as many
times as needed on a piece of MDF or plywood until
the bottom of the upper pole reaches the 6”
mark (on Sticker) on the bottom pole. See Figure 3.
Before putting any of the poles tubes together, make sure that the orange
area of the Warning Sticker on Pole (#2) is 6 inches (15.25cm) from the top
end. Be sure that the “Back Side” stickers are on the back of the
pole. See Figure 3.
If you want to see a video on how to put the poles together go to:
http://support.escaladesports.com/customer-service/instruction-videos/basketball
WARNING: This pole assembly is heavy. Step 2 may require two
adults. Make sure you can control the pole when slamming it
together. If you are unsure if you can safely control the pole ask
another adult to help you. This helper can stand on the opposite
side of the pole. Attention should be paid to one’s feet and toes
during entire slamming process.
NOTE : When slamming poles together make sure to
keep the poles straight. Slamming the poles down
crooked will damage the bottom of the pole. Top Pole
must cover upper orange area of sticker. If Pole goes
slightly past the 6” mark, it is OK.
IMPORTANT! DO NOT hit poles with hammer or sledge
hammer to attach poles together. Figure 3
3
2
Be sure to match up both
“Back Side” stickers on
the back of the poles and
that the holes on top pole
are toward the back.
FAILURE TO FULLY ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
BACKSIDE
Bottom of upper pole must cover the
above orange portion of this sticker
(6” mark).
WARNING
!
4L-8151-00
PIECE OF
PLYWOOD / MDF
(must be at least as
big as pole plate)
BURY LINE
Or Scan with your
smart phone:
NOTE : Top Pole must cover
upper orange area of sticker.
If Pole goes slightly past the 6”
mark, it is OK.
6

INSTRUCTIONS CONTINUED
POST ASSEMBLY
42
42
Figure 4
NOTE : Self Drilling screws (#42)
are used. Holes are only on
outside Pole. User must insert
screws through BOTH POLES.
3. Once the Top pole is to the 6” Mark on the Warning Sticker, lay Pole Assembly on its side on two padded saw
horses. Insert a (#42) Screw into each 3/16” hole in top Pole, two on each side of the Post Assembly. You will
need someone to hold the Pole assembly while inserting screws. Screw must go through both Top and Bottom
(Inner) Poles. Make sure to not strip screws once they are all they way through. See Figure 4.
SCREWS (#42) MUST BE INSTALLED TO POLE AS DESCRIBED
IN STEP 3. FAILURE TO INSTALL SCREWS COULD RESULT IN
SERIOUS INJURY OR PROPERTY DAMAGE.
NOTE : Cordless drill required for screw installation. Do not over tighten screws causing screws to
strip. Once Screw heads touch pole, STOP! Overtightening will cause Pole to Warp and
damage system.
NOTE : To install screws, it will be easier if you use a cordless drill with 5/16” socket (instead of
Phillips head).
NOTE : Screws #42, used in step 3, are Self Drilling screws and can be installed without drilling pilot
holes. However, it will be easier to install screws if you drill 9/64” pilot holes in bottom pole.
WEAR SAFETY GLASSES if drilling holes.
7

BURY LINE
Figure 5
4. Mix concrete per the instructions on concrete bag. Pour into the hole
and stop about 16” from Playing Surface or until you can still see the top
of the Masonry block you placed earlier. See Figure 5 and Detail 1.
5. Set the bottom of the pole on the masonry block in the hole. Make
sure the Pole stays on the block as shown in Figure 5. The Bury line
should be level with the playing surface see Detail 1.
While one person holds the pole in place have two other people finish
pouring concrete up to court level. Use a level to make sure Pole is vertical.
6.
Detail 1
PLA
YING SURFACE
IMPORTANT
BE SURE THAT THE HOLES ARE TOWARD THE
BACK OF THE POLE AND “BACK SIDE”
STICKERS ARE AT THE BACK OF THE POLES/
OPPOSITE THE PLAYING SURFACE BEFORE
POURING CONCRETE ON STEPS 4-6.
(Court Level)
THE FOLLOWING STEPS WILL REQUIRE
AT LEAST THREE CAPABLE ADULTS.
IMPORTANT
16"
PLAYING SURFACE
8

7. Stabilize the pole by using six 2X4’s and placing two 50 lbs.
bags of sand on top to keep pole from shifting, periodically
check the pole with level to ensure that pole is vertical.
See Figure 6.
8. Let concrete Stand for a MINIMUM of 48 hours (2 days).
Note: Periodically check pole with level to ensure that pole is vertical.
Figure 6
IMPORTANT!
Let concrete stand for a MINIMUM of 48
hours (2 days) before proceeding to the
next step. In humid climates or wet
weather, allow additional time for the
concrete to cure. Do not install anything
else until concrete is completely cured.
Sand bag
2 X 4’s
9

9. Attach Post Ears (#30) to holes near the bottom of Top
Post (#3) using two hex bolts (#25) four washers (#18) 3
2
IMPORTANT! BE SURE CONCRETE HAS BEEN
ALLOWED TO CURE FOR AT LEAST 2 DAYS.
Figure 7
GOALIATH ASSEMBLY INSTRUCTIONS (Day 3)
10.
11.
12. Place Pole Cap (#1) onto top of Top Pole (#3). Note: Pole
13. Secure two stop spacers (#10) to pole, as shown in Figure 8,
using one hex bolt (#7) and one lock nut (#4). Tighten Lock
Figure 8
Detail 2
Slide tab on Actuator (#16) between Post Ears (#30) and
Secure using one bolt (#19), two washers (#20) and one
lock nut(#21). Tighten Lock Nut (#21) snug but do not
Cap may be pre-installed by the factory.
Note: If necessary, use a rubber mallet to tap in
Pivot Tube (#14)
If not already pre-assembled, slide Plastic Actuator Sleeve (#15)
over Steel Actuator (#16) and place Actuator Cap (#13) on top.
Align holes in all 3 parts and slide Pivot Tube (#14) through holes
in Actuator Cap (#13), Plastic Actuator Sleeve (#15) and Steel
Actuator (#16) until equal amounts stick out through both sides of
actuator. See Figure 8.
7
1
10
4
14
15
16
19
20
21
13
BACK SIDE
BACK SIDE
and two lock nuts (#4). Do not tighten nuts (#4)
completely until instructed to do so. See Figure 7 &
Detail 2.
nuts (#4) from Step 9.
over tighten. See Figure 8. At this time also tighten
Nut (#4) but do not over tighten.
10