ESCALADE GOALRILLA B2412 User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly of your basketball system easier, use the Hardware Identifier on page 3
and 4 to identify and sort all fasteners. Check all cartons for kits. All hardware is not located
in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
OWNER'S MANUAL
MODEL NO.
B2B2
B2B2
B2412412
412412
412
Goalrilla
Hooplight
Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: 1-888-USA-GOAL Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [email protected]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®SPORTS PRODUCT INFORMATION
2L-6798-01
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

3
Note: This unit is equipped with U-Bolts to fit GoalrillaTM and
GoaliathTM basketball units with 4 x 4, 5 x 5, 6 x 6, and 6 x 8
poles. Select the U-Bolt by measuring your pole and referring to
the "Hardware Identifier" in this manual.
1. Attach a Black Bracket (#17) to pole 3" below top pivot point, as
shown in Figure 1, using a U-Bolt (#18), two washers (#15) and two
hex nuts (#16).
2. Attach a second Black Bracket (#17) 13" from top pivot point, as
shown in figure 1, using a U-Bolt (#18), two washers (#15) and two
hex nuts (#16).
Figure 1
6. Remove the wing nut, lock washer and screw at top of light that holds
frame together. The door frame assembly will swing down to open.
Using gloves or soft cloth insert one end of bulb into socket specified
on light. Gently apply pressure to the bulb and insert opposite end of
bulb into other socket. Close door and secure with screw, lock washer
and wing nut. Repeat for other light unit. Note: Do not touch
halogen bulb with your hand as oil in your skin will cause
damage to the bulb. Reverse this procedure to remove the
bulb.
3. Identify Pole Sections "A" through "D" by their labels.
4. Hold Pole Section "D" (#11) next to the Black Brackets (#17) with
1" of pole below the bottom Black Bracket (#17). Place a U-Bolt
(#14) around the Pole Section "D" (#11) and into the small slots
of the Black Bracket (#17). Secure using the two flat washers
(#15) and hex nuts (#16). See Figure 2. Note: Do not over
tighten as there may be some adjusting required.
5. Repeat the last step with the other Black Bracket (#17) and U-
Bolt (#14).
Figure 2
Figure 3

4
11. Slide the swaged (crimped) end of Pole Section "B" (#9) into the
unthreaded end of Pole Section "A" (#8). Align the holes and
insert a self tapping screw (#12) to secure. (You will need to use
a wrench or a pair of pliers to firmly start the self tapping screw.)
12. Slide Pole Section "C" (#10) into the end of Pole Section "B" (#9)
and secure with a self tapping screw (#12).
Note: It is very important to evenly space out the six plastic
ties to keep the electrical cord secure.
13. Secure the electrical cord to the pole with six plastic ties (#13) in
the locations shown in Figure 6. Cut off excess plastic tie.
Figure 4
Figure 5
9. Install a Serreated Washer (#19) onto Lamp Base (#3) and screw
the threaded portion of the Lamp Base (#3) into the threaded
end of Pole Section "A" (#8). Secure Lamp Base by tightening
jam nut on Lamp Base (#3) against end of Pole Section "A" (#8).
See Figure 5.
10. Attach Lamp Base (#3) and Light Junction Box to Lamp Mount
Bar (#2) using two Washer Head Bolts (#4), two washers (#5)
and two locknuts (#6). See Figure 5.
7. Attach Halogen Lamp Assembly (#1) to Lamp Mount Bar (#2)
using four Washer Head Bolts (#4), four washers (#5) and four
locknuts (#6) as shown in Figure 4.
8. Mount the Wire Safety Cage (#7) to the frame on the front of the
Halogen Lamp Assembly (#1). Squeeze the cage slightly so the
wire ends fit into the inside four corners of the frame.
Figure 6

5
14. With the help of at least one other adult, lift hooplight assembly
up and insert Pole Section "C" (#10) on top of Pole Section
"D" (#11). Secure with a self tapping screw (#12). See Figure
7. If necessary, align hooplight with basketball unit by
loosening U-Bolts (#14) slightlyslightly
slightlyslightly
slightly. Tighten U-Bolts (#14) when
adjustments are complete.
15. Secure the remaining electrical cord to the pole with two plastic
ties (#13) in the locations shown in Figure 7. Cut off excess
plastic tie.
ATTACHING HOOP LIGHT TO POLE REQUIRES
AT LEAST TWO CAPABLE ADULTS.
When attaching the Hoop Light to the pole, stay clear of all
overhead power, electrical, telephone wires, and obstacles.
Any contact between the Hoop Light and any of these lines will
result in immediate danger.
WARNING: When mounting the Hoop Light to the basketball
pole, be sure that no U-clamp either traps or squeezes the
electrical cord. Make sure the electrical cord is free and placed
outside of the U-clamps. Do not plug the Hoop Light into any
electrical outlet or extension cord until the entire assembly
procedure is complete.
Figure 7

6
!Lamp surface gets very hot. Unplug lamp and allow to cool before touching surface of lamp. Do not assemble
without the guard.
!Lamp should remain at least 20 inches from any sort of flammable material.
!This is not an indoor lamp.
!Do not look directly into lamp
!Keep children away from this lamp.
!Lamp should be unplugged and completely cool before you attempt to replace the bulb. Avoid direct contact of
fingers with the bulb. Oil from skin can damage the bulb.
!Do not operate lamp with broken pieces or missing safety guard.
!Never operate lamp around highly flammable liquids such as gasoline or paint thinner.
!This lamp should never be in or near a wet surface. Never use near a swimming pool, hot tub or sauna, or
near a standing body of water.
!Do not operate this lamp in the rain.
!Always insert the plug into the outlet carefully.
CAUTION:
HOOPLIGHT CARE INFORMATION
Reverse the mounting procedure carefully in order to reach the lamp for cleaning the safety glass, changing the bulb, or in the
rare occasion that you might need to redirect the beam of the light fixture.
Use 500 watt or smaller, type T-3 bulb. (Available at most hardware and home stores)

7
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE®SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAM-
AGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW
INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF
DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our satisfaction
to be thus defective, please contact our Warranty Dept.
1-888-USA-GOAL / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Products. ESCALADE® SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PE-
RIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CON-
SUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.

82L-6798-01
1 6Q-6007-00 Dual 500 watt Hal Lamp Assy 1
2 4A-6870-00 Lamp Mount Bar 1
3 4A-6843-00 Lamp Base 1
4 1B-6602-00 M6 X 1.0 X 25 Hex Washer Head 6
5 2B-6014-00 M6 Flatwasher 6
6 2B-6142-00 M6 X 1.0 Nylon Locknut 6
7 6Q-6006-00 Wire Safety Cage 2
8 8S-6687-00 Pole Section "A" 1
9 8S-6688-00 Pole Section "B 1
10 8S-6689-00 Pole Section "C 1
11 8S-6690-00 Pole Section "D 1
12 1B-6563-00 Self Tapping Screw 3
13 7B-6290-00 Plastic Tie 8
14 7B-6294-00 3/8" U-Bolt 2
15 701-50 3/8" Flatwasher 8
16 901-28 3/8-16 Nylon Locknut 8
17 7B-6293-00 Black Bracket 2
18 7B-6295-00 U-Bolt for 4 X 4 Pole 2
7B-6296-00 U-Bolt for 5 X 5 Pole 2
7B-6297-00 U-Bolt for 6 X 6 Pole 2
7B-6298-00 U-Bolt for 6 X 8 Pole 2
19 2B-6147-00 M20 Serrated Lockwasher 1
Key# Part # Description Qty.