ESCALADE STIGA T8620 User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 16 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, 3/8 Wrench, and Two 7/16 Wrenches (adjustable
wrenches may be substituted for the wrenches).
O W N E R ' S M A N U A L
2L-7631-00
2017 Escalade Sports
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
TABLE TENNIS TABLE
MODEL NOS.
T8620
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our Website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
Please Do Not Return This Product To The Store!
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer
has to be contacted for replacement parts.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use
caution because you could overtighten the hardware and strip the screws.

For aid in identifying hardware, see hardware identifier on pg 16.
2. Align U-Support (#7) on Table Top as shown in
Figure 1.
1. Lay Table Top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
2
1
7
Note: Indentations are
small so look closely.
End Rail Mounting
Indentations
Figure 3
Figure 3
Figure 1
A. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could
overtighten the hardware and strip the screws.
B. Indentation mounting guides are small so look closely when attaching hardware.
C. Table top can be set on top of two saw horses. Although this will make assembly easier it is not necessary to complete
assembly. Always use shipping container to protect the painted surface of the table top.
CAUTION: Make sure that the table top is secure on sawhorses and NEVER leave the table top unattended.
ASSEMBLY TIP

CAUTION:
If you want to see a video on how to position the U-Clips go to:
http://www.escaladesports.com/customer-service/videos.html
Or scan with your smartphone:
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#3) BE TURNED
AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY, YOU WILL DO IRREPARABLE
DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION.
20
3
IMPORTANT:
Slot in
U-Clip
End Rail Mounting
Indentations
Detail A
3. Align the holes in the U-clips #3 with Indentations in table top assembly
and secure with twelve screws #20 as shown. All four holes in each U-Clip
must align with four Indentations in top. See Figure 2 and Detail A.
Be sure that slot in the three U-clips #3 all face the
same direction as shown. (Toward the end of the
table with no stripe.)
3
Figure 3
Figure 3
Figure 2
#8 x 7/16
Sheet Metal Screw
(Qty. 12)
Hardware Needed

34
33
20
20
Detail B
4. Align the holes in the Mounting Brackets #33 & #34 with
Indentations in table top assembly and secure with screws #20
as shown. All holes in each Mounting Bracket must align with
Indentations in the top. See Figure 3 and Detail B.
Figure 3
Figure 3
Figure 3
4
Hardware Needed
Note: Indentations
in table top are small
so look closely.
#8 x 7/16
Sheet Metal Screw
(Qty. 20)

5. Attach Legs (#2) to Mounting Bracket (#34) with Hex Bolt (#38),
two Plastic Washers (#24) and Locknut (#15). Attach leg brace
to Leg Mounting Bracket (#33) with Phillips Head Screw (#37)
and Locknut (#16) as shown in Detail C.
Figure 3
Figure 3
Figure 4
6. Attach Leg Plugs (#13) to bottom of the Legs (#2) as shown in
Figure 4.
24 15
16 37
2
Leg Brace
38
33
34
Detail C
5
13
24
Plastic Washer
(Qty. 4)
15
1/4” Locknut
(Qty. 2)
Hardware Needed
37 #10-24 X 1/2 Phillips
Pan Head Screw
(Qty. 2)
38
#10-24 X 1/2 Phillips Locknut
(Qty. 2)
16
1/4-20 x 2 1/4 Hex Head Bolt
(Qty. 2)

Note: Legs not
shown for Clarity
Figure 3
Figure 3
Figure 5
19
3
7
Detail D
7
Note: Rotate U-Support #7 until you see the screw
hole in the slot of U-clip #3. Slide U-support #7
side to side and front to back if necessary.
6
7. Insert Screw #19 through slot in U-Clip #3 and into U-
Support #7. Thread it all the way into U-Support #7 until it
touches the back of the tube. There should be about 3/8
inch of screw #19 left sticking out. Do not insert
screw#19 in middle #3 U-Clip. See Figure 5 & Detail D.
If you want to see a video on how to insert Screw (#19) go to:
http://www.escaladesports.com/customer-service/videos.html
Or
Scan with your smartphone:
Note: Rotate U-Support #7 until you see the screw hole in the
slot of U-clip #3. Slide U-support #7 side to side and front to
back if necessary.
Hardware Needed
19
#8-32 X 1 1/4
Phillips Head Screw
(Qty. 2)
Note: To aid in assembly use a cordless drill and Phillips bit, but be
careful to not strip the screws. Wear safety glasses for Step 7.

10. Line up holes in rails with indentations in
top and secure using eighteen screws
#20. See Figure 6 & Detail E.
26
25
20
Shorter Distance
Longer Distance
35 (RH)
Note: Legs not
shown for Clarity
8. Lay out Right Side Rails #25, Left Side Rails
#29 and End Rails #26, around edges of
table top as shown in Figure 6.
Figure 3
Figure 3
Figure 6
20
9. Slide Left #36 and Right #35 Vinyl End
Caps onto the ends of the Side Rails #25
& 29 as shown in Detail E.
Detail E
11. Lay Corner Caps #22 on table as shown
in Figure 6. If Corner Cap sticks above
the table top surface of the table, flip over
so shorter distance is against edge.
Secure to bottom of table with three
Screws #21. See Detail F.
Detail F
Note: Rails attach
with #20 screws
7
20
Hardware Needed
21
#8 x 1 7/16
Sheet Metal Screw
(Qty. 6)
#8 x 7/16
Sheet Metal Screw
(Qty. 18)
Note: U-Support not
shown for Clarity
(RH Rail)
Note: Stiga
logo must be on
this end of Rail.
(LH Rail)
29
Note: Stiga
logo must be on
this end of Rail.

11
12
7
4
23
4
15
31
2
Detail G
Figure 3
Figure 3
Figure 7A
First Table Top
13. On one side of the table attach slotted end of safety strap #6 to
INSIDE of Leg #2 using one bolt #39, one spacer #30, one washer
#24, and one hex nut #15. Tighten hardware until snug but do not
overtighten. Tubes must pivot freely. See Detail H.
14. Attach other end of safety strap #6 to OUTSIDE of linkage #4
using one bolt #9, one washer #24, one spacer #30, and
one hex nut #15 as shown in Detail H.
12. Attach end of linkages #4 with two holes to INSIDE of Leg #2 as shown
in Detail G & Detail H. Secure through end hole with screws #23,
locknuts #15 and plastic spacers #31. Tighten hardware snug enough to
keep table stable but do not overtighten. Tubes must pivot freely.
Important! Do NOT put other safety strap #6 on this
table half. It will be installed on second table half later.
15. Gently tap caster sockets #12 into U-support #7 until
flange on sockets touches the edge of the tube. DO
NOT HIT CASTER SOCKET DIRECTLY WITH A
HAMMER! SET A PIECE OF WOOD ON CASTER
SOCKET AND HIT PIECE OF WOOD TO DRIVE
CASTER SOCKET INTO U-SUPPORT.
16. Insert casters #11 into caster sockets #12.
See Figure 7A.
8
15
24
30
30
6
31
39
23
2
4
924
15
Detail H
15
1/4” Locknut
(Qty. 3)
39 1/4-20 x 2 1/2 Hex Head Bolt
(Qty. 1)
1/4-20 x3 1/4 Hex Head Bolt
(Qty. 2)
30
3/4” Spacer
(Qty. 2)
31
5/16” Spacer
(Qty. 2)
24 Plastic Washer
(Qty. 2)
1/4-20 x 1 1/2 Bolt
(Qty. 1)
9

17. Attach other end of linkages #4 to OUTSIDE
of U-support #7 with bolts #14 and plastic
washers #24. Then slide name panel #5
onto the same bolts #14 on the INSIDE of
U-support #7. Secure with lock nuts #15 See
Figure 7B. Tighten hardware until snug but
do not overtighten. Tubes must pivot freely.
18. Attach bottom of name panel #5 to
U-supports #7. Secure with hex
bolts #9 and locknuts #15. Tighten
nuts but be careful not to crush
tubes. See Figure 7B.
20. Prepare an area for the assembly of the second table top half. If necessary,
move the first table top half aside with the aid of a helper. Be sure to place it
in a location where it won't be disturbed or damaged. If setting on its side, be
Figure 3
Figure 3
Figure 7B
First Table Top
9
AT LEAST TWO ADULTS ARE NEEDED
TO MOVE TABLE HALF!
CAUTION:
9
14
1/4-20 x 1 1/2” Bolt
(Qty. 2)
24
Plastic Washer
(Qty. 2)
15
¼” Locknut
(Qty. 8)
Hardware Needed
sure to place the bottom edge no less than 12 inches away form the wall. Also
be sure to place carpet or pieces of the shipping carton down to protect table
top edges. If floor is not carpeted, brace table top half with a heavy object to
keep it from sliding.
1/4-20 x 2” Bolt
(Qty. 2)18
15
32
15
24
14
9
9
14
24
15
32
5
15
7
4
7
19. Attach bottom board #18 to name
panels #5, as shown in Figure 7B, using
four bolts #32 and four hex nuts #15.
1/4-20 x 1-1/4” Bolt
(Qty. 4)

14
24
15
4
21. Repeat steps from 1-16 on second half.
AT LEAST TWO ADULTS ARE NEEDED
TO MOVE TABLE HALF!
CAUTION:
22. Attach linkages #4 to the OUTSIDE of U-support #7 on
second table half. Use Bolts #14, plastic washers #24
and hex nuts #15. See Figure 8.
NOTE: Tighten locknuts #15 finger tight
only. They will be removed when the
two table top halves are connected. Figure 3
Figure 3
Figure 8
Second Table Top
NOTE: Tighten locknuts #15 finger tight
only. They will be removed when the two
table top halves are connected.
10
14
24
Plastic Washer
(Qty. 2)
15
1/4” Locknut
(Qty. 2)
Hardware Needed
1/4-20 x 2” Bolt
(Qty. 2)
24
14
15
7