Escort PASSPORT 8500CI Plus User manual



 Please read both sides of these
instructions before starting your
installation.
For the easiest trouble-free
installation, install the Interface
first, and wire it to a 12-volt
switched circuit.
Then before installing the other
components, plug all of them
into the Interface and power up
the unit to confirm proper
operation.
To get the best possible
performance, installation of the
Radar/Laser receiver is critical.
Although radar signals will pass
through some materials,
including plastic, laser signals
will not. For this reason the
receiver must have a clear view
of the road in order to work
properly.

 
 
 Installation of this system
requires some experience and
expertise in automotive
electronics. Car Audio specialists
and many new car dealers can
install this for you.
 If you choose to install it
yourself without expertise in
automotive electronics, please
note that it can cause personal
injury or damage to your vehicle.
 If your vehicle is damaged
during installation, its safety
systems may be compromised
and could cause personal injury
or property damage.
 Improper installation may
also void PASSPORT’s warranty.

 
 
 
Front Radar/Laser Receiver
• Miniature weather-proof Radar/Laser
Receiver
• Universal mounting bracket with
stainless steel hardware
• Built-in 16 foot shielded cable with
water proof connector
• 12 nylon wire ties to secure cable
Miniature Display Controller
• Display Controller mounts easily to
instrument pod, dashboard or
console
• Optional hidden display included
Interface
• Central module connects to
switched 12-volt power and ground
• All components plug directly in
using modular connections
• 3M connector taps into existing
vehicle wiring
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are
operational
• Fully compatible with Laser Shifters
NOTE: INSTALL THE RECEIVER
HORIZONTALLY AND LEVEL,
WITH A CLEAR VIEW OF THE
ROAD.
                       
                         
S i m p l e . E a s y . I n s t a l l e d .

PASSPORT 8500ci Installation Manual
E
C
D
A
B
A
A
F
Display Controller
1 Determine the best location for the
Display Controller in the vehicle’s interior.
(Consult customer if necessary.)
2 Remove paper backing on the backside
of the display and apply to a clean dry
surface.
3 Route display cable and plug into jack
marked “Display” on the Interface.
Interface
1 Install Interface under the dash using
supplied zip-ties. DO NOT MOUNT IN
ENGINE COMPARTMENT.
2 Connect black wire (–) to ground, and
red-striped wire (+) to a switched 12-volt
supply. (If PASSPORT is left in the “on”
position, it will automatically power on
and off with the ignition). Use blue 3M
connector (provided) to tap into existing
circuit if needed.
3 Receiver and Display Controller plug
into the Interface. Be sure to plug all
cables into the correct jacks.
Interior of Vehicle
12 Volt
Power Line
±
Front Radar/Laser Receiver
1 Determine the best location for the
Radar/Laser Receiver. The best location is
typically under the bumper, or inside the
front grill of the vehicle. For the best
performance, install the Receiver
horizontally, with a clear “view” of the
road.
2 Using the built-in mounting holes on
the Receiver, or the supplied right-angle
mounting bracket, mark the hole locations.
Drill pilot holes in the vehicle if necessary.
3 Mount the Receiver using the supplied
hardware. (If right-angle mounting bracket
is used, secure the Receiver to the right-
angle bracket first, then install bracket
with Receiver to the vehicle.)
Concealed LED Display (Optional)
If a more discreet display is preferred the
included LED can be installed:
1 Drill a 1/4" hole, and install the LED clip.
2 Snap LED into clip from behind.
3 Plug the modular connector into
PASSPORT’s Interface marked “LED.”
Receiver Cable
1 Connect the receiver cable to the
receiver.
2 Route cable through the firewall, and
secure with zip-ties (included).
3 Route receiver cable into the vehicle’s
interior. If there is not a suitable opening,
drill a 13/32" or 7/16" hole.
4 Pull cable through firewall, and plug
connector into the jack labeled “Antenna”
on the Interface.
TEST
After all components are installed
correctly:
1 Turn vehicle’s ignition to the “on”
position.
2 Turn PASSPORT on by pressing the
power button located on the front of
the Display Controller.
3 PASSPORT will cycle through a short
startup sequence.
4 If any error messages come up, see the
Owner’s Manual for details.
5 Pull cable through the firewall and seal
the hole as needed. Use silicone sealant
(not supplied) if necessary.
NOTE:
1. Only drill hole in firewall after
thoroughly investigating location first,
ensuring no other wires, hoses, etc. will be
damaged.
2. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
3. Do not splice cable.
NOTE:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
B
E
NOTE:
1. Make certain that the Display is clearly
visible from the driver’s position, and that
the controls can be easily accessed
without interfering with normal driving.
D
C
ESCORT RADAR DETECTORS RADAR DETECTORS