Esteam Ninja Mister User manual

ESTEAM CLEANING SYSTEMS
OWNER’S MANUAL
Congratulations on your selection of a new Ninja Mister Sprayer built in
Canada by “Esteam Cleaning Systems.” Our goal has been to produce the
best high performance line of cleaning equipment on the market today.
Reading your owner’s manual will help to achieve maximum benefit from
your purchase.
VERSION 01 (May 2020)
NINJA MISTER

1
TABLE OF CONTENTS
Page No.
Intro on the Ninja Mister 2
Specifications 2
Maintenance 3
Safety Information 3
Operating Instructions 4
Trouble Shooting 5 & 6

2
INTRODUCTION
Be it a small residential job or a large commercial contract, Esteam Cleaning Systems
industrial cleaning equipment are right for your needs. The Ninja Mister delivers the
ultimate in power, capacity, durability, and performance. The Ninja Mister is a
lightweight portable electronic sprayer.
Only the highest quality components go into our equipment, to deliver you strength and
reliability in a long life high performance machine. All Esteam Cleaning Systems
equipment housings are made of high impact, unbreakable polyethylene.
The Ninja Mister incorporates a dual 150-psi demand pumps for single or dual
operators.
SPECIFICATIONS
NINJA MISTER
NJA - MIST
ELECTRICAL
Amps
Volts
One cord
4 amps
115 volts(220volts)
PUMP
Dual 150 psi
SOLUTION TANK
Two 10.5 gallons (40 litres)
LENGHT
26 inches (66 cm)
WIDTH
17 inches (43 cm)
HEIGHT
34 inches (86 cm)
WEIGHT
70 lbs (49.8 kgs)

3
MAINTENANCE
DAILY:
- Rinse out pumps with clean water at conclusion of workday.
- Clean poly housing with mild soap and water.
MONTHLY:
- Clean acorn screen in both tanks.
YEARLY:
- We recommend that a qualified service technician inspect your unit once a
year.
PREVENTATIVE MAINTENANCE:
-Never store this unit in a place where there is a possibility of the temperature
dropping below 00C (320F).

4
SAFETY INFORMATION
1. Prior to inspection or repair of this machine, disconnect all electrical cords
rendering the machine powerless. Failure to do so could result in serious or fatal
injury.
2. Inspect unit daily for worn or damaged components. E.g. frayed cord, loose plug,
or a plug with missing ground pin, etc.
3. This unit should only be operated when in an upright position on a level surface.
4. Do not operate unit unless it is properly grounded in a 3 pin grounded outlets.
Never bend or remove ground pin from plugs.
5. Ensure filters are free from lint or dirt.
6. Do not run unit if pumps are wet. Allow sufficient time for motor to dry before
plugging unit in.
7. Do not use solvent-based cleaning products in the Ninja Mister.
8. Do not use solution tanks for storing hoses, cords or accessories
9. When using electrical equipment around water it is important to wear rubber
soled shoes and keep machine properly grounded at all times. Failure to do so
could result in a fatal electric shock.
OPERATING INSTRUCTIONS
1. Insert electrical cords into 3 pin grounded outlets.
2. 150 PSI pump priming instructions:
- Fill fresh water tanks
- Connect solution hose.
- Turn on pump
- Depress trigger on spray guns until solution flows freely
- Machine is ready to use.

5
OPERATING INSTRUCTIONS (CONTINUED)
DANGER: No solvents of any type may be used in this system at any time. The use of
solvents is extremely hazardous resulting in possible fire and/or explosion.
3. Connect solution hoses to the sprayer wand or wands
4. Proceed to apply solution
WARNING: When using electrical equipment around water it is important to wear
rubber-soled shoes and keep machine properly grounded at all times. Failure to do so
could result in electric shock.

6
TROUBLE SHOOTING
WARNING: Prior to inspection or repair of this machine, disconnect all
electrical cords rendering the machine powerless. Failure to do so could
result in serious or fatal injury.
PROBLEM CAUSE SOLUTION
1. Entire unit will not 1. Unit not plugged in 1. Connect unit to 3 pin
operate grounded outlets
2. Loose wiring 2. See dealer
2. Pump 1. Switch not turned on 1. Turn on switch
will not run
2. Broken switch 2. See dealer
3. Loose wiring 3. See dealer
4. Pump motor defective 4. See dealer
4. Pump runs but does 1. Out of solution 1. Fill solution
not pump solution
2. Pump inlet screen plugged 2. Clean inlet screen
3. Pump was not properly 3. Prime pump using
primed priming hose
4. Kink in solution hose 4. Remove kink
5. Plugged jet or quick connect 5. Remove blockage
6. Internal (inside machine) or 6. See dealer
external solution line damaged
and leaking

7
TROUBLE SHOOTING (CONTINUED)
PROBLEM CAUSE SOLUTION
5. Pump runs but 1. Partial kink in solution hose 1. Remove kink
has loss pressure
2. Partial blockage in solution 2. Remove blockage
hose
3. Jet orifice opening on clean- 3. Total jet opening for 150
ing wand is too large PSI pump should be .06 or
4. Internal pump components 4. See dealer
wearing out
6. Water accumulate- 1. Inside solution line leaking 1. Immediately shut unit
ing in bottom electrical down. Bring unit to a
component area dealer for service
2. Pump leaking 2. Immediately shut unit
down. Bring unit to a
dealer for service
3. Solution tanks 3. Immediately shut unit
leaking from above down. Bring to a dealer
for serving