ESYLUX HAST 1000 User manual

HALOGEN FLOOD LIGHT
GB
www.esylux.com
Please follow the manufacturer’s instructions for inserting the bulb.
The protective cover on the bulb should not be removed until the bulb has been
fitted. Do not touch the bulb with your bare hands. When changing the light bulb
ensure that the halogen flood light has cooled down to ambient temperature.
NB: The protective glass is a temperature-resistant safety glass with a thickness of
5 mm; the flood light should nevertheless be mounted so that water (e.g. rain)
does not fall directly onto the protective glass (high surface temperature of the
protective glass).
Congratulations on your purchase of this high-quality ESYLUX product.
To ensure proper operation, please read these user instructions carefully and keep them for
future reference.
SAFETY INSTRUCTIONS
CAUTION: Work on the 230 V power system must be carried out by authorised
personnel only with due regard to the applicable installation regulations. Switch off the
power supply before installing the system.
Use this product only as intended (as described in the user instructions). Changes or
modifications to the product or painting it will result in loss of warranty. You should
check the device for damage immediately after unpacking it. If there is any
damage, you should not install the device under any circumstances. If you suspect
that safe operation of the device cannot be guaranteed, you should turn the device
off immediately and make sure that it cannot be operated unintentionally.
When working on the halogen flood light please bear in mind that the surface
can become extremely hot.
Any damaged protective glass must be immediately replaced.
2 • DESCRIPTION
ESYLUX HAST 1000 and HAST 1500 are halogen flood lights ranging from
750 - 1500 Watt. All flood lights are supplied with a wall bracket to allow
quick and easy wall mounting.
Bulbs are not supplied.
3 • INSTALLATION / ASSEMBLY / CONNECTION
Please note the following points before installation:
• Switch off the mains supply before installing the product.
• It is essential that you observe the minimum distances (fig. 2.1, 2.2 and 2.3)
and the installation restrictions (fig. 2.4).
• The halogen flood light should only be mounted on a solid, even base.
Use the wall bracket as a template for the mounting distance.
Mount the halogen flood light at the selected site (fig. 1).
Open the connection box and feed the cable through the cable connection
and the cable grip as shown in fig. 3.1 and 3.2.
Connect the halogen flood light as shown in the circuit diagram (fig. 4).
Close the connection box wit the screw-down cover and turn the lock nut on
the cable connection tight (fig. 3.3).
Now fit the appropriate light bulb (fig. 5) and close the halogen flood light
as directed.
FIG. 1
HALOGEN FLOOD LIGHT
GB
• •HAST 1000
• •HAST 1500 min. 1 m
min. 1 m
min. 0,05 m
min. 50°
2.3
2.4
min. 90°
min. 1 m
2.1 2.2
3.1 3.3
FIG. 2
FIG. 3
FIG. 4 FIG. 5
1
1
2
2
1
2

ESYLUX GmbH
Postfach 1834, 22908 Ahrensburg/Germany
Internet: www.esylux.com
e-mail: [email protected]
WA 05/2009
4 • ESYLUX WARRANTY
ESYLUX products are tested in accordance with applicable regulations and
manufactured with the utmost care. The duration of the warranty is based on
statutory guidelines. The warranty can only be honoured if the appliance is sent
back with the receipt, unchanged, packed and with sufficient postage to ESYLUX
GmbH or to the relevant distributor in your country. (Visit www.esylux.com for a
complete overview.) Please include a brief written description of the fault with any
device you send back. If the warranty claim proves justified, ESYLUX GmbH will,
within a reasonable period, either repair the device or replace it. If a claim is
unfounded (e.g. because the warranty has expired or the fault is not covered by the
warranty), then ESYLUX GmbH will attempt to repair the device for you in a cost-
effective manner. The warranty does not apply to natural wear and tear, changes
caused by environmental factors or damage in transit, nor to damage caused as a
result of failure to follow the installation or user instructions. Any batteries or bulbs
supplied with the device are not covered by the warranty.
ESYLUX GmbH shall not be liable for any indirect, consequential or financial losses.
TECHNICAL DATA
MAINS VOLTAGE 230 V ~ 50 Hz
HAST 1000: 750 - 1000 W/R7s
HAST 1500: max. 1500 W/R7s
COLOUR
white/black/silver grey
PROTECTION TYPE/CLASS IP 55/I
FOR BULB
(NOT SUPPLIED)
Technical and design features may be subject to change.
width 407 mm, height 384 mm, depth 171 mm APPROX. DIMENSIONS