Chauvet Intimidator Scan 305 IRC User manual

User Manual

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 2 of 27
T
ABLE OF
C
ONTENTS
1. Before You Begin.........................................................................................................................4
What is Included .............................................................................................................................................................4
Unpacking Instructions....................................................................................................................................................4
Claims.............................................................................................................................................................................4
Text Conventions............................................................................................................................................................4
Symbols ..........................................................................................................................................................................4
Disclaimer .......................................................................................................................................................................4
Product at a Glance ........................................................................................................................................................5
Safety Notes ...................................................................................................................................................................5
2. Introduction ..................................................................................................................................6
Overview.........................................................................................................................................................................6
Dimensions .....................................................................................................................................................................7
3. Setup.............................................................................................................................................8
AC Power........................................................................................................................................................................8
Fuse Replacement..........................................................................................................................................................8
Power Linking .................................................................................................................................................................9
Power Linking Diagram..............................................................................................................................................9
Mounting .......................................................................................................................................................................10
Orientation ....................................................................................................................................................................10
Rigging..........................................................................................................................................................................10
Rigging Diagram......................................................................................................................................................10
4. Operation....................................................................................................................................11
Control Panel Description.............................................................................................................................................11
Menu Map................................................................................................................................................................11
Configuration (DMX).....................................................................................................................................................13
DMX Starting Address.............................................................................................................................................13
DMX Personalities...................................................................................................................................................13
DMX Channel Assignments and Values..................................................................................................................14
11-CH .................................................................................................................................................................................14
7CH.....................................................................................................................................................................................17
Configuration (Standalone)...........................................................................................................................................19
Sound Mode ............................................................................................................................................................19
Auto Mode ...............................................................................................................................................................19
Manual Mode...........................................................................................................................................................19
Configuration (Settings)................................................................................................................................................20
Pan Reverse............................................................................................................................................................20
Tilt Reverse..............................................................................................................................................................20
Screen Reverse.......................................................................................................................................................20
Reset........................................................................................................................................................................21
Reset to Factory Defaults........................................................................................................................................21
System Information.......................................................................................................................................................21
IR Mode ...................................................................................................................................................................22
IRC-6 Operation................................................................................................................................................................22
Configuration (Master/Slave)........................................................................................................................................23
Configuring the Slaves.............................................................................................................................................23
Configuring the Master ............................................................................................................................................23
5. Technical Information................................................................................................................24

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 3 of 27
Product Maintenance....................................................................................................................................................24
6. Technical Specifications ...........................................................................................................25
Returns............................................................................................................................................26
Contact Us ......................................................................................................................................27

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 4 of 27
1.
B
EFORE
Y
OU
B
EGIN
What is
Included
•
Intimidator™ Scan 305 IRC
or
•
Intimidator™ Barrel 305 IRC
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check that all the parts are in the package and
are in good condition.
Claims
If the box or any of the contents appear damaged from shipping, or show signs of mishandling,
save all packaging and file a claim with the carrier immediately, do not notify Chauvet. Failure
to report damage to the carrier immediately
or failure to have all packaging available for
inspection may invalidate your claim.
For other issues, such as missing components or parts, damage not related to shipping
, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
For information on
contacting Chauvet, see the Contact Us section of this manual.
Text
Conventions
Convention
Meaning
1–512
A range of values
50/60
A set of values
Settings
A menu option
Menu > Settings
A sequence of menu options
<ENTER>
A button to be pressed
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information. Not following
these instructions can make the product not work, cause damage to the
product, or cause harm to the operator.
Important installation or configuration information. The product might
not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual are subject to change without
notice. Chauvet assumes no responsibility or liability for any errors or omissions, and reserves
the right to revise or recreate this manual at any time. The latest version of this manual should
be downloaded from http://www.chauvetlighting.com/product-manuals-literature/.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author
Date
Editor
Date
R. Isenstadt
04/08/15
A. Leon
05/08/15

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 5 of 27
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, use, and maintenance of this
product. Read these notes before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Make sure the power cord is not crimped or damaged.
•Always disconnect the product from the power source before cleaning it or replacing the
fuse.
•Never disconnect the product from the power source by pulling or tugging on the cord.
•If mounting the product overhead, always secure it using a safety cable.
•Make sure there are no flammable materials close to the product when it is operating.
•Avoid direct eye exposure to the light source while the product is on.
•Do not touch the product’s housing when the product is operating because the housing can
be very hot.
•This product is not intended for permanent installation.
•The product is for indoor use only! It is rated at IP20.
•To prevent risk of fire or shock, do not expose the product to rain or moisture.
•Always make sure that the voltage of the power source to which the product is connected
is within the range stated on the sticker or rear panel of the product.
•Never connect the product to a dimmer or rheostat.
•Make sure to replace the fuse with another of the same type and rating.
•Always install the product in a location with adequate ventilation, and leave at least 20 in
(50 cm) between the product and adjacent surfaces.
•Always use the handles to carry this product.
•The maximum ambient temperature (Ta) in which the product can be used is
104 °F (40 °C). Do not operate the product at higher temperatures.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never carry the product by the power cord or any moving part.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to damage
or malfunction. Contact the nearest authorized technical assistance center.
•To eliminate wear and improve its lifespan, during periods of non-use completely
disconnect from power via breaker or by unplugging it.
Keep this User Manual for future reference. If you sell the product to another user, be sure to
give this manual to the next owner.

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 6 of 27
2.
I
NTRODUCTION
Overview
Back Panel View
Safety Cable
Pass-Through
Front View (Barrel) Front View (Scan)
DMX In/Out
Power In
Fuse Holder
Power Out
Mirror
Adjustable
Lens
Display
IR Sensor
LED Indicator
Menu Buttons

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 7 of 27
Dimensions
18.9 in
480 mm
6.7 in
171 mm
10 in
255 mm
Barrel
Scan
10 in
255 mm
16.9 in
430 mm
5.7 in
147 mm

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 8 of 27
3.
S
ETUP
AC Power
The Intimidator™ Scan/Barrel 305 IRC have auto-ranging power supplies that work with an
input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use
the values listed on the label affixed to the product’s back panel, or refer to the product’s
Specifications. The listed current rating indicates the product
’s average current draw under
normal conditions.
The Intimidator™ Scan/Barrel 305 IRC can be power linked via the IEC and Edison outlets in
its base.
•Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure circuit
has an appropriate electrical ground to avoid the risk of electrocution or
fire.
•Never connect the product to a rheostat (variable resistor) or dimmer, even if the
rheostat or dimmer serves only as a 0 to 100% switch.
•To eliminate wear and improve its lifespan, during periods of non-
use completely
disconnect from power via breaker or by unplugging it.
Fuse
Replacement
Make sure product is not connected to a power source.
1. Place the tip of a flat-head screwdriver into the slot in the fuse holder.
2. Turn the screwdriver counterclockwise and the fuse holder will come loose.
3. Pull the fuse holder out of the product.
4. Pull the blown fuse out of the fuse holder.
5. Place a new fuse of the exact same type and rating into the fuse holder.
6. Insert the fuse holder into the product.
7. Place the tip of a flat-head screwdriver into the slot in the fuse holder.
8. Turn the screwdriver clockwise and the fuse holder will tighten into place.
•Disconnect the product from power before replacing the fuse.
•Use only the fuse listed in the Technical Specifications section or on the
specifications sticker on the product.
•A spare fuse is not included.

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 9 of 27
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the unit.
Power Linking
Diagram
Up to 5 Intimidator™ Scan/Barrel 305 IRC units can be linked on 120 V, or up to 12
Intimidator™ Scan/Barrel 305 IRC units on 230 V.
•The power linking diagram shown above corresponds to the North American version
of the product ONLY!
•If using this product anywhere other than North America, consult with the local
Chauvet distributor because power linking connectors and requirements differ from
country to country, and region to region.
1st
Product
2nd
Product
3rd
Product
Additional Products

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 10 of 27
Mounting
Before mounting the product, read and follow the safety recommendations in the Safety Notes
section.
Orientation
The Intimidator™ Scan/Barrel 305 IRC can be mounted in any position, but make sure the
placement allows adequate ventilation for the product, and allows for movement of the yoke
and head in any direction.
Rigging
Be sure to place the product in a location that allows easy access to it for maintenance and
programming, and enough space around the product for ventilation.
Make sure that the structure or surface onto which the product will be mounted can support
the
product’s weight. For more information see the Technical Specifications section.
When mounting the product overhead, always use a safety cable and make sure the product is
attached securely.
When mounting the product on a truss or pipe, use a mounting clamp with the appropriate
weight capacity. Chauvet has a full range of mounting clamps.
See
http://www.chauvetlighting.com/cables-clamps-main.html for the complete selection.
The rubber feet serve as floor supports. When placing the product on the floor, make sure that
the product and cables are away from people and vehicles.
Rigging Diagram
Safety Cable
(such as CH-05 from
Chauvet)
Mounting Clamps
(such as CLP-15 from Chauvet)
Hanging/
Mounting
Bracket
Rubber Feet (x4)
Secure the safety cable
using the pass-
through on
the back of the product

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 11 of 27
4.
O
PERATION
Control Panel
Description
The control panel is used to set the operating mode, and the configuration settings of the
product. Use the 4 buttons underneath the LCD
display to access the control panel and
navigate the menu map. For specific instructions see the Configurations sections below.
Button
Function
<MENU>
Enters into, or backs out of, the current menu option
<UP>
Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER>
Activates a selected menu or value
Menu Map
The Menu Map presents all the options in the menu system, and the values to set them.
Menu
Value
Description
Address
001–512
Sets the DMX starting address
Run Mode
DMX
7CH
Sets DMX personality
11CH
Slave
Slave1–4
Sets Slave mode
Auto
Sets Auto mode
Sound
Sets Sound mode
IR
Sets infrared control
Manual
Pan
000–255
0 to 180°
Tilt
0 to 90°
P/T Speed
Pan/Tilt speed (fast to slow)
Color
Selects color options
Dimmer
Sets dimmer value
Shutter
Strobe effect with increasing speed
Gobo
Selects Gobo options
Gobo
Rotate
Rotation effect with increasing
speed
Prism
Selects 3-facet prism
Special
Function Selects control functions
P/T Macro
Selects pan/tilt movement macros

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 12 of 27
Menu
Value
Description
Setup
Pan Reverse
OFF
Normal pan operation
ON
Reverse pan operation
Tilt Reverse
OFF
Normal tilt operation
ON
Reverse tilt operation
Screen
Reverse
OFF
Normal display
ON
Upside-down display
Sensitivity
001—100
Sets sound sensitivity
Reset
Resets the product
Factory Set
Loads factory defaults
Sys Info
Ver: VX.X
Running Mode: XXXX
DMX Address: XXX
Temperature: XXX
Shows the current software version,
running mode, DMX address and
product’s temperature

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 13 of 27
Configuration
(DMX)
To set the product in DMX mode for control with a DMX controller, do the following:
1. Make sure the product is plugged into a power source.
2. Connect the male end of a DMX cable to the DMX out socket of the DMX controller and
the female end of the same cable to the DMX in socket on the product.
3. Set the DMX starting address and personality by following the directions below.
DMX Starting
Address
When selecting a starting DMX address, always consider the number of DMX channels
needed for the selected DMX personality. Choosing a starting address that is too high can
restrict access to some of the product’s channels.
The Intimidator™ Scan/Barrel 305 IRC uses either 7 or 11
channels, depending on the
personality. The highest configurable DMX address in 7-channel mode is 506. The highest
configurable DMX address in 11-channel mode is 502.
For more information about DMX download the Chauvet DMX Primer from the Chauvet web
site http://www.chauvetlighting.com/download.
To set the DMX starting address, do the following:
1. If the display shows a number from 001–512, go to step 5.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight Address.
4. Press <ENTER> and a number from 001–512 will show on the display.
5. Use <UP> or <DOWN> to change the number to the desired DMX starting address.
6. Press <ENTER> to select the DMX starting address.
DMX Personalities
The Intimidator™ Scan/Barrel 305 IRC has 2 DMX personalities: a 7-channel personality and
an 11-channel personality.
To set the DMX personality, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Run Mode icon.
3. Press <ENTER> and the Run Mode options will show on the display.
4. Use <UP> or <DOWN> to highlight DMX.
5. Press <ENTER>. A green dot will show on the DMX option line and the characters 7CH
or 11CH will show in green.
6. Use <UP> or <DOWN> to switch between 7CH and 11CH.
7. Press
<ENTER>
to select the DMX personality shown.
After the DMX starting address and personality have been set, there will be a delay of
30 seconds before the display automatically returns
to showing the current DMX
address and the DMX personality.

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 14 of 27
DMX Channel
Assignments and
Values
The following table outlines all the capabilities of the Intimidator™ Scan/ Barrel 305 IRC and
the channels that control them when the light is used with a lighting controller.
11-CH
Channel
Function
Value
Percent/Setting
1
Pan
000
ó
255
0–180°
2
Tilt (Scan)
000
ó
255
0–90°
Tilt (Barrel)
000
ó
020
Stop
021
ó
135
Clockwise rotation (slow to fast)
136
ó
140
Stop
141
ó
255
Counter-clockwise rotation (slow to fast)
3
Pan/Tilt Speed
000
ó
255
Fast to slow
4 Color
000
ó
006
Open (white)
007
ó
013
Yellow
014
ó
020
Purple
021 ó027
Green
028 ó034
Red
035 ó041
Light Blue
042 ó048
Kelly Green
049 ó055
Orange
056 ó063
Dark Blue
064 ó070
White + Yellow (split colors)
071
ó
077
Yellow + Purple (split colors)
078
ó
084
Purple + Green (split colors)
085 ó091
Green + Red (split colors)
092 ó098
Red + Blue (split colors)
099 ó105
Light Blue + Kelly Green (split colors)
106 ó112
Kelly Green + Orange (split colors)
113 ó119
Orange + Dark Blue (split colors)
120 ó127
Dark Blue + White (split colors)
128 ó191
Rotate counter-clockwise (slow to fast)
192
ó
255
Rotate clockwise (slow to fast)
5 Shutter
000
ó
003
Closed
004
ó
007
Open
008
ó
076
Synchronized Strobe (slow to fast)
077 ó145
Pulse Strobe (slow to fast)
146 ó215
Random Strobe (slow to fast)
216 ó255
Open

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 15 of 27
11-CH
Channel
Function
Value
Percent/Setting
6
Dimmer
000
ó
255
0 to 100%
7 Gobo Wheel
000 ó007
Open
008 ó015
Gobo 1 (glass)
016 ó023
Gobo 2 (glass)
024
ó
031
Gobo 3
032 ó039
Gobo 4
040 ó047
Gobo 5
048 ó055
Gobo 6
056 ó063
Gobo 7
064
ó
071
Gobo 7 shake, fast to slow
072 ó079
Gobo 6 shake, fast to slow
080 ó087
Gobo 5 shake, fast to slow
088 ó095
Gobo 4 shake, fast to slow
096 ó103
Gobo 3 shake, fast to slow
104
ó
111
Gobo 2 (glass) shake, fast to slow
112 ó119
Gobo 1 (glass) shake, fast to slow
120 ó127
Open
128
ó
191
Gobo scroll: counter-clockwise rotation
192 ó255
Gobo scroll: clockwise rotation
8 Gobo Rotation
000 ó063
Gobo indexing
064 ó147
Rotate clockwise (slow to fast)
148 ó231
Rotate counter-clockwise (slow to fast)
232 ó255
Gobo bounce
9 Prism
000
ó
007
Prism
008
ó
255
Stop, static prism effect

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 16 of 27
11-CH
Channel
Function
Value
Percent/Setting
10 Operating Mode
000 ó007
No function
008 ó015
Pan/tilt move-in-black
016 ó023
Pan/tilt move-in-black (disable)
024 ó031
Color wheel move-in-black
032
ó
047
Gobo wheel move-in-black
048 ó055
Color wheel and Gobo wheel move-in-black
(disable)
056 ó063
Fast movement
064 ó087
Fast movement (disable)
088
ó
095
All movement move-in-black (disable)
096
ó
103
Reset pan/tilt
104
ó
111
No function
112
ó
119
Reset color wheel
120 ó127
Reset gobo wheel
128 ó135
No function
136 ó143
Reset prism
144 ó151
Reset focus
152 ó159
Reset all
160 ó255
No function
11 Movement
Macros
000 ó007
No function
008
ó
023
Automatic 1
024
ó
039
Automatic 2
040
ó
055
Automatic 3
056 ó071
Automatic 4
072 ó087
Automatic 5
088 ó103
Automatic 6
104 ó119
Automatic 7
120 ó135
Automatic 8
136 ó151
Sound 1
152 ó167
Sound 2
168
ó
183
Sound 3
184
ó
199
Sound 4
200 ó215
Sound 5
216 ó231
Sound 6
232 ó247
Sound 7
248 ó255
Sound 8

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 17 of 27
7CH
Channel
Function
Value
Percent/Setting
1
Pan
000
ó
255
0 to 180°
2
Tilt (Scan)
000
ó
255
0 to 90°
Tilt (Barrel)
000
ó
020
Stop
021
ó
135
Clockwise rotation (slow to fast)
136
ó
140
Stop
141
ó
255
Counter-clockwise rotation (slow to fast)
3 Color
000
ó
006
Open (white)
007 ó013
Yellow
014 ó020
Purple
021 ó027
Green
028 ó034
Red
035 ó041
Light Blue
042 ó048
Kelly Green
049 ó055
Orange
056
ó
063
Dark Blue
064
ó
070
White + Yellow (split colors)
071
ó
077
Yellow + Purple (split colors)
078 ó084
Purple + Green (split colors)
085 ó091
Green + Red (split colors)
092 ó098
Red + Blue (split colors)
099 ó105
Light Blue + Kelly Green (split colors)
106 ó112
Kelly Green + Orange (split colors)
113 ó119
Orange + Dark Blue (split colors)
120 ó127
Dark Blue + White (split colors)
128
ó
191
Rotate counter-clockwise (slow to fast)
192
ó
127
Rotate clockwise (slow to fast)
4 Shutter
000 ó003
Closed
004 ó007
Open
008 ó076
Synchronized Strobe (slow to fast)
077 ó145
Pulse Strobe (slow to fast)
146 ó215
Random Strobe (slow to fast)
216 ó255
Open

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 18 of 27
7CH
Channel
Function
Value
Percent/Setting
5 Gobo Wheel
000
ó
007
Open
008 ó015
Gobo 1 (glass)
016 ó023
Gobo 2 (glass)
024
ó
031
Gobo 3
032 ó039
Gobo 4
040
ó
047
Gobo 5
048 ó055
Gobo 6
056 ó063
Gobo 7
064
ó
071
Gobo 7 shake, fast to slow
072 ó079
Gobo 6 shake, fast to slow
080 ó087
Gobo 5 shake, fast to slow
088 ó095
Gobo 4 shake, fast to slow
096 ó103
Gobo 3 shake, fast to slow
104
ó
111
Gobo 2 (glass) shake, fast to slow
112 ó119
Gobo 1 (glass) shake, fast to slow
120
ó
127
Open
128 ó191
Gobo scroll: counter-clockwise rotation
192 ó255
Gobo scroll: clockwise rotation
6 Gobo Rotation
000 ó063
Gobo indexing
064 ó147
Rotate clockwise (slow to fast)
148 ó231
Rotate counter-clockwise (slow to fast)
232 ó255
Gobo bounce
7 Prism
000 ó007
Prism
008
ó
255
Stop, static prism effect

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 19 of 27
Configuration
(Standalone)
Use standalone configurations to operate the product without a DMX controller.
Never connect a product operating in a standalone mode (Sound, Auto, or IR) to a
DMX chain that includes a DMX controller. Products in standalone mode can transmit
DMX signals that interfere with the DMX signals from the controller
Sound Mode
Sound mode sets the product to respond to sounds and music.
To set the product to Sound mode, do the following:
1. Make sure the product is connected to a power source a
nd not connected to a DMX
controller.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER> and the Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Sound option.
6. Press <ENTER>. A green dot will show on the Sound
option line and the product will
begin reacting to sound.
The product will respond only to low frequencies of music (bass and drums).
If the product is not responding to sound, increase the sensitivity.
For more
information see the Sensitivity Setting below.
Auto Mode
Auto mode sets the product to 1 of 16 preset movement patterns and color changes.
To set the product to Auto mode, do the following:
1. Make sure the product is connected to a power source
and not connected to a DMX
controller.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER> and the Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Auto option.
6. Press <ENTER>. A green dot will show on the Auto
option line and the product will
begin moving and emitting light.
Manual Mode
Manual mode allows the user to control every function of the Intimidator™ Scan/Barrel 305
IRC through the LCD display. To run the product in Manual mode, follow the instructions
below:
1. Make sure the product is connected to a power source and not connected to a DMX
controller.
2. Press <MENU> repeatedly until 4 icons show on the display.
3. Use <UP> or <DOWN> to highlight the Run Mode icon.
4. Press <ENTER> and the Run Mode options will show on the display.
5. Use <UP> or <DOWN> to highlight the Manual option.
6. Press <ENTER> and the Manual options will show on the display.
7. Use <UP> or <DOWN> to select Pan, Tilt, P/T Speed, Color, Dimmer, Shutter, Gobo
,
Gobo Rotate, Prism, Special Function, or P/T Macro.
8. Press <ENTER> and the current value (000–255
) of the selected function will be
highlighted.
9. Use <UP> or <DOWN> to increase or decrease the value of the selected function.
10. Press <ENTER>.
11. Repeat steps 7–10 until the product is set as desired.

Intimidator™ Scan/Barrel 305 IRC User Manual Rev. 1 Page 20 of 27
Configuration
(Settings)
The Intimidator™ Scan/Barrel 305 IRC can be customized with settings such as pan direction,
screen orientation, and sound sensitivity. Below are instructions for configuring
all the settings
available.
Pan Reverse
Reversing the pan movement is useful when 2 lights are facing each other and they both need to
turn toward the same direction.
To reverse the pan movement do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>.The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Pan Reverse option.
5. Press <ENTER>. The words ON or OFF will show in green.
6. Use <UP> or <DOWN> to switch between ON and OFF.
7. Press
<ENTER>
to select the setting.
Tilt Reverse
Reversing the tilt movement is useful when 2 lights are facing each other and they need to point
towards the same space between them.
To reverse the tilt movement, do the following: Press <MENU> repeatedly until
4 icons show on
the display.
1. Use <UP> or <DOWN> to highlight the Setup icon.
2. Press <ENTER>. The Setup options will show on the display.
3. Use <UP> or <DOWN> to highlight the Tilt Reverse option.
4. Press <ENTER>. The words ON or OFF will show in green.
5. Use <UP>or <DOWN> to switch between ON and OFF.
6. Press
<ENTER>
to select the setting.
Screen Reverse
The display can show the screen in two directions, one for when the fixture is standing and one
for when it is mounted upside-down.
To set the display orientation, do the following:
1. Press <MENU> repeatedly until 4 icons show on the display.
2. Use <UP> or <DOWN> to highlight the Setup icon.
3. Press <ENTER>. The Setup options will show on the display.
4. Use <UP> or <DOWN> to highlight the Screen Reverse option.
5. Press <ENTER>. The words ON or OFF will show in green.
6. Use <UP> or <DOWN> to switch between ON (upside-down display) and
OFF (normal display).
7. Press <ENTER> to select the setting.