Martec Guard User manual

20W WALL MOUNT
TRICOLOUR FLOODLIGHT
GUARD
Model No.: MLXG34520MS

2
20W WALL MOUNT
TRICOLOUR FLOODLIGHT
IMPORTANT PRODUCT INFORMATION
YEAR REPLACEMENT
WARRANTY

Parts List
1. Light body
2. Wall mount bracket
3. Tricolour switch
4. Glass cover
5. Cable
6. Cable plug
7. Sensor lens
8. Sensor Time control
9. Sensor sensitivity control
10. Sensor Lux control
10. Wall mount screws
LED Floodlight 20 Watt with PIR sensor Tricolour
aluminium body + glass lamp cover + stainless steel bracket
Color: Black
Voltage: 220-240VAC~50/60Hz
LED: 28x0.7W Everlight LED 3000K;
28x0.7W Everlight LED 5000K;
Color temperature: 3000-5000K;
Lumen: 3000K---1400lm;
4000K---1600lm;
5000K---1600lm;
Cord length: with AU plug; H05RN-F 3Gx1.0mm²; 60cm length;
With Tricolour button switch on the housing, press to change the colour temperature
with LED shield; RA≥80
With PIR sensor
Detection angle: Max.180°
Detection Distance:Max.12m
Adjustable Time:10±5 seconds to 4±1 minutes adjustable
LUX:From daylight to night adjustable
Sense: adjustable
IP44
11
8 9 10
www.martecaustralia.com.au | 02 8778 7500 | [email protected] Page 3
6
13
5
2
4
7
TIME SENS LUX

www.martecaustralia.com.au | 02 8778 7500 | [email protected] Page 4
Product Installation
NOTE: For best performance install at a height between 2 and 2.5 metres.
1. Ensure the Mains Supply is switched‘OFF’.
2.
wired to its own wall switch.
3. Adjust the wall mount bracket .
4. Drill two holes in the wall using the mounting holes‘B’ on the wall mount bracket as a template.
Note: exercise caution to avoid drilling into existing electrical wiring.
use the cable plug‘D’ to plug the light into a wall switch, set the color temperature to your desire
setting using the Tricolour switch ‘C’.
Adjust the light to your desire position, Then turn on the light by turn on the wall switch.
,
5.
6.
7. Adjust the sensor to your desire direction by adjusting the sensor head 'E'.
• Do not direct the head upwards above horizontal.
• Always operate the sensor with sensor knobs
facing downwards.
B
A
E
D
C
E

SENS (Sensitivity Adjustment)
• The sensitivity can be increased by turning the knob towards (+)
and decreased by turning the knob towards (–).
• Note:
temperature. The sensor is more sensitive at lower environmental
temperatures and vice versa.
TIME
• The time duration is adjustable from. Turn this knob towards (+) to
increase the time, or turn it towards (–) to decrease the time.
• Note: Once the light is activated by the PIR sensor, any subsequent
detection will restart the time again from the beginning.
• The light will stay‘ON’until the duration of the time set by this
knob has expired.’
LUX (Lux Control Adjustment)
• The LUX control has a built-in photocell that detects daylight and darkness.
• – Turning the LUX knob into this position means that the PIR sensor will turn the light ON at ‘Daytime’
(as well as at night time).
• – Turning the LUX knob into this position means that the PIR sensor will turn the light ON only at ‘Night’.
• Desired LUX level can be set by adjusting the LUX knob between the ‘Daytime‘ and‘Night’.
The PIR motion sensor has three adjusting knobs: SENSITIVITY, TIME and LUX.
Motion Sensor Settings
Good sensitivity walking
across the detection area.
Poor sensitivity
walking towards or
away from the sensor.
WALK THROUGH TEST
• Set the TIME knob to min (–) the LUX level to ( ) and SENS knob to (+) position and wait approximately a minute
for the control circuit to stabilise. Do not stand within the sensing range of the sensor!
• Direct the sensor towards detection area by adjusting the swivel joint on the sensor arm.
•
• Walk slowly across the detection area. The sensor will detect the infrared radiation of the human body and turn
the light ON.
• Test the coverage of the area by walking further away from the sensor until you get satisfactory result. Adjust the
direction of the sensor left or right or up or down if required.
• Once you are happy with the direction, don’t forget to set the TIME and re-adjust the SENSITIVITY and LUX level
required from day ( ) to night ( ) operation.
5
TIME SENS LUX

On the back of the LED light body, there is Tricolour switch which allows you to switch the colour
temperature of the light among 30000K (WW), 4000K (NW), 5000K (CW).
6

7
(For Warranty Conditions please refer to the Martec Website for Warranty Terms and Conditions)