Etch A Sketch 7002 User manual

For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-TEC-TOYS or 1-800-832-8697
[e-mail]
Etch A Sketch #7002
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. [phone] / Fax [phone]
Toll Free 800.832.8697
www.enablingdevices.com

A classic now adapted!
Activate your way to great looking pictures with the world classic Etch A
Sketch. The four built-in switches allow you to go in horizontal or vertical
directions. Just watch the magic screen where your lines begin to form exciting
drawings. When you are finished, just take it off the base and shake and then
you are ready to start again. The base also has 4 external jacks for your
capability switches should your child require them. Size: 8"H x 13"W x 11 1/2
"D. Requires 6 C Batteries.
Operation:
1. Etch A Sketch requires 6 C batteries (Not included). Use alkaline batteries
only (e.g. Duracell or Energizer brand). Do not use rechargeable batteries or
any other type of batteries because they supply lower voltage and the unit
will not perform properly. Never mix old and new batteries together or
different brands or types together.
2. The battery compartment is located under the bottom of the Control Consol.
To remove the battery compartment cover, carefully turn the unit over, and
then pull the cover off. Next undo the Velcro battery retaining strap. Install
new batteries, being careful to observe proper battery polarity. Set the ON
OFF switch to ON, redo strap and replace cover.
3. This is the Classic Etch A Sketch drawing toy which we have motorized.
Push one of the two yellow Button switches to make the lines go up or down
(indicated by the directional arrows). Push one of the two Red Button
switches to make the lines go right or left (indicated by the directional
arrows).
4. If you push one of the Yellow and Red Button switches together, you can
make a triangle, circle; or different angles.
5. The Etch A Sketch can be taken off its base so you can clear the screen. To
do this carefully tilt and pull up on the Etch A Sketch from the top. The Etch
A Sketch is held in place by Velcro. Please Note: The Etch A Sketch
cannot be removed completely because there is wiring is attached to it.
The best way to clear the screen is hold the unit level up side down tap
lightly on the screen then shake gently with a back and forth or a rotating
motion. When finished clearing the screen place the unit back in its base.
6. Should the non toxic powdery contents escape, do not brush. It is easily
cleaned when sponged lightly with soap and water
7. There are 4 external switch input jacks on the sides of the unit so other
switches can be used in place of the built in Button switches. There is also a
picture holder in the center of the base.
Important Notes:
When you are finished using the Etch A Sketch, turn the ON/OFF switch to
OFF to prevent accidental activation of the Button switches and battery
drain.
For prolong periods of storage we recommend removing the batteries.
From time to time batteries left in devices for prolonged periods can leak
their acid which can cause damage to the electronics in the device.
Troubleshooting:
Problem: Etch A Sketch does not work.
Action #1: Check all batteries for proper (+) & (-) battery polarity.
Action #2: Replace all batteries with fresh new batteries. Never mix different
brands or old and new batteries.
Problem: Etch A Sketch works intermittently or very slowly.
Action #1: Check all batteries for proper (+) & (-) battery polarity.
Action #2: Replace all batteries with fresh new batteries. Never mix different
brands or old and new batteries.
Care of Unit:
Etch A Sketch can be wiped clean with any household multi-purpose cleaner
and disinfectant. We recommend Simple Green, which is a non toxic
biodegradable all-purpose cleaner.
Do not submerge the unit, as it will damage the contents and the electrical
components.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
Rev 7/28/10