Eternal Lighting Premier150 Spot User manual

Premier150 Spot Eternal Lighting Feb 2016
Eternal
Lighting
Premier150™ Spot
User Manual
Introduction:
Thank you for your purchase of the Premier150™ Spot. When unpacking and before disposing of
the carton, check there is no transportation damage before using the projector. Should there be
any damage caused by transportation, consult your dealer and do not use the apparatus.

Premier150 Spot Eternal Lighting Feb 2016
Safety Measures:
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other
liquids.
DO NOT mount the projector directly onto an inflammable surface
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 20 inches fr o m
adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not project the beam onto in ammable surfaces, minimum dis5 inches.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye. Do not attempt to
dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by quali ed personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector. It is essential that each projector is correctly earthed and that
electrical installation conforms to all relevant standards. Do not connect this device to any
other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-
cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out
the plug by tugging the power-cord.
Keep a projector’s optical system clean. Do not touch LED lens with bare hands.
The projector should always be installed with a secondary safety cord.
Shields and lens shall be changed if they have become visibly damaged to such an extent than
their effectiveness is impaired, for example by cracks or deep scratches.
LED lamps should be replaced if damaged or having reached life limit.
Exterior surface temperatures of the luminaire after 5 minutes operation is 55C°, when steady
state is achieved 70C°.
There is no user serviceable parts inside the projector do not open the housing and never operate
the projector with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
Features:
•RGBW 150 Watt LED
•Output Lux @ 1m 40700 and @ 2m 12300+ (Comparable to 575 Watt Bulb)
•Light Source: 150 Watt RGBW LED - 60,000 Hour LED Engine Life
•Drive current 2.25 Amp
•Electrical Input Voltage 90 ~ 240V AC 50-60Hz
•Power Consumption 125W max at full output

Premier150 Spot Eternal Lighting Feb 2016
•Control Protocol / DMX512 On-board Display for Auto and Sound Active Control & Master/Slave
Functions
•DMX Modes (16CH, 18CH and 24CH Modes)
•Optical System Focus Electronic DMX Focus
•Dimmer 0-100% 8-Bit in 16CH and 18CH or 16-Bit in 24 CH
•Strobe Variable speed Mechanical (1Hz ~ 13Hz)
•Prism Rotating 3-facet prism
•Movement Pan 540° Tilt 270°
•Pan/tilt resolution 8-16 bit
•Special Pan/Tilt Movement Blackout
•User-selectable pan/tilt ranges
•2 Gobo Wheels
(One Fixed Gobo Wheel: 7 gobos +Open
(One Rotating Gobo Where 7 Gobos Metal and Glass +Open)
•Gobo-flow effect
•Gobo shake
•Gobo Morphing
•Bi-directional rotation
•Millions of Colors because No Color Where - Smooth color mixing
•Rainbow-flow effect
•Physical Dimensions Base 17 3/4" x 17" / Base to Head Up 17"
•Weight 29.8 lbs
•Housing Flame-retardant heavy duty plastic
•Case Color Black
•3Pin DMX in and out
•Powercon Power Input
•DMX in/out
•Cooling Forced Convection
•Max. Ambient TEMP 113° F (45°C)
Power Supply
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the main power to the projector paying attention to the voltage and
frequency marked on the panel of the projector. It is recommended that each projector be supplied
separately so that they may be individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to
all relevant standards.
Control Connection

Premier150 Spot Eternal Lighting Feb 2016
DMX OUT DMX IN
2 1
3 PIN
DMX OUT DMX IN
515
5 PIN
4 2 2 4
33
Connection between controller and projector and between one projector and another must be made
with a 2 core-screened cable, with each core having at least a 0.5mm diameter.
Connection to and from the projector is via cannon 5 pin (which are included with the projector) or 3
pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each
other. The body of the plug is not connected in any way. The projector accepts digital control signals in
protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the
second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last
fixture’s output to a DMX terminator as shown in the figure below.
DMX Terminator
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a
DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control
signals.
The DMX terminator is simply an XLR connector with a 120 Ω(ohm) resistor connected across pins
2 and 3, which is then plugged into the output socket on the last projector in the chain.
Setup Options
The Premier150 Spot configuration can be set conveniently by pressing the buttons on the LCD
display. To browse or change the setup options, press ENTER to unlock the panel. Menu will be
displayed on the screen; each menu has its own sub-menu. Each menu has specific function, refer to
“Operation Menu” for detals.
FUNC D OWN UP ENTER
DMX512
PI N FUNCTION
1 GND
2 DATA-
3 DATA+
DMX512
PI N FUNCTION
1 GND
2 DATA-
3 DATA+
4 N/C
5 N/C

Premier150 Spot Eternal Lighting Feb 2016
•Press UP or DOWN if you want to browse or change through the various Setup Options
•Press ENTER to save your settings or ENTER the next menu
•Press UP or DOWN to change values (Add or subtract)
•Press FUNC to return to the upper menu one by one
To Set The DMX Start Address:
Each projector must be given a DMX start address so that the correct projector responds to the
correct control signals. This DMX start address is the channel number from which the projector
starts to “listen” to the digital control information being sent out from the controller.
The fixture has 3 DMX modes.
•Simple mode
•Standard mode
•Extended mode.
For example standard mode has 18 channels, so set the No. 1 projector’s address 001, No. 2
projector’s address 019, No. 3 projector’s address 037, No. 4 projector’s address 055 and so on.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel
Press the UP or DOWN to set the address
Press ENTER to save the command and will remember what is saved after you unplugged the fixture
Press UP or DOWN to change values
Press FUNC to return to main menu
Operation Menu
Level
1
Level
2
Level
3
Level
4
LED Stage Light
150W Led Spot
DMX Address = 001
LED Stage Light
150W Led Spot
Auto = P01:S01
LED Stage Light
150W Led Spot
Master = P01:S01
LED Stage Light
150W Led Spot
Slave = P01:S01
LED Stage Light
150W Led Spot
Slave same
LED Stage Light
Address Setup LED Stage Light
Address Setup
Address = 001
LED Stage Light
Reset
LED Stage Light
Reset Effects
LED Stage Light
Reset Pan& Tilt
LED Stage Light
Reset Complete
LED Stage Light
ManualOperation LED Stage Light
ManualOperation
Pan LED Stage Light
ManualOperation
Pan = 000
LED Stage Light
ManualOperation
Tilt
LED Stage Light
ManualOperation
Tilt = 000
LED Stage Light
ManualOperation
Red LED Stage Light
ManualOperation
Red = 000

Premier150 Spot Eternal Lighting Feb 2016
LED Stage Light
ManualOperation
Green LED Stage Light
ManualOperation
Green= 000
LED Stage Light
ManualOperation
Blue LED Stage Light
ManualOperation
Blue = 000
LED Stage Light
ManualOperation
White
LED Stage Light
ManualOperation
White = 000
LED Stage Light
ManualOperation
Strobe
LED Stage Light
ManualOperation
Strobe = 000
LED Stage Light
Manual Operation
Fixed Gobo Wheel
LED Stage Light
Manual Operation
Fixed Gobo = 000
Level 1 Level 2
Level
3
Level
4
LED Stage Light
Manual Operation
Rot. Gobo Wheel
LED Stage Light
Manual Operation
Rot. Gobo = 000
LED Stage Light
Manual Operation
Gobo Rotation
LED Stage Light
Manual Operation
Gobo. Rot = 000
LED Stage Light
Manual Operation
Prism
LED Stage Light
Manual Operation
Prism = 000
LED Stage Light
Manual Operation
Prism Rotation
LED Stage Light
Manual Operation
Prism. Rot = 000
LED Stage Light
Manual Operation
Focus
LED Stage Light
Manual Operation
Focus = 000
LED Stage Light
Operation Mode
LED Stage Light
Mode =
DMX Mode
LED Stage Light
DMX Mode =
Short Mode
LED Stage Light
DMX Mode =
Standard Mode
LED Stage Light
DMX Mode =
Extended Mode
LED Stage Light
Mode =
Auto Mode
LED Stage Light
Select Program
Program = x
LED Stage Light
Mode =
Master Mode
LED Stage Light
Select Program
Program = x
LED Stage Light
Mode =
Slave S YN C Mode
LED Stage Light
Select Program
Program = x
LED Stage Light
Mode =
Slave SAME Mode
LED Stage Light
Option Settings
LED Stage Light
Option
Pan Tilt Swap
LED Stage Light
Pan Tilt Swap
=O FF
LED Stage Light
Pan Tilt Swap
=ON
LED Stage Light
Option
Pan Invert
LED Stage Light
Pan Invert
=O FF

Premier150 Spot Eternal Lighting Feb 2016
LED Stage Light
Pan Invert
=ON
LED Stage Light
Option
Tilt Invert
LED Stage Light
Tilt Invert
=O FF
Level 2 Level 3 Level 4
LED Stage Light
Tilt Invert
=ON
LED Stage Light
Option
Display Set up
LED Stage Light
Display Set up
Delay Off
LED Stage Light
Delay Off
= Disable
LED Stage Light
Delay Off
= Enable
LED Stage Light
Display Set up
Display Invert
LED Stage Light
Display Invert
= OFF
LED Stage Light
Display Invert
= ON
LED Stage Light
Display Set up
Language
LED Stage Light
Language
= English
LED Stage Light
Language
LED Stage Light
Option
Lost DMX
LED Stage Light
Lost DMX
=Clear Value
LED Stage Light
Lost DMX
=Hold Value
LED Stage Light
Advanced
LED Stage Light
Access Code
LED Stage Light
Access Code
Code = 000
Code = 008
LED Stage Light
Adjust
LED Stage Light
Adjust
Pan
LED Stage Light
Adjust
Pan = +000
LED Stage Light
Adjust
Tilt
LED Stage Light
Adjust
Tilt = +000
LED Stage Light
Adjust
Red
LED Stage Light
Adjust
Red = +000
LED Stage Light
Adjust
Green
LED Stage Light
Adjust
Green = +000
LED Stage Light
Adjust
Blue
LED Stage Light
Adjust
Blue = +000
LED Stage Light
Adjust
White
LED Stage Light
Adjust
White = +000
LED Stage Light
Adjust
Fixed Gobo Whee l
LED Stage Light
Adjust
Fixed Gobo = +000
Level 1
Level 2
Level 3
Level 4
LED Stage Light
Adjust
Rot. Gobo
Wh l
LED Stage Light
Adjust
Rot. Gobo =
000

Premier150 Spot Eternal Lighting Feb 2016
Level 1 Level 2 Level 3 Level 4
LED Stage Light
Tilt Invert
=ON
LED Stage Light
Option
Display Setup
LED Stage Light
Display Set up
Delay Off
LED Stage Light
Delay Off
= Disable
LED Stage Light
Delay Off
= Enable
LED Stage Light
Display Set up
Display Invert
LED Stage Light
Display Invert
= OFF
LED Stage Light
Display Invert
= ON
LED Stage Light
Display Set up
Language
LED Stage Light
Language
= English
LED Stage Light
Language
LED Stage Light
Option
Lost DMX
LED Stage Light
Lost DMX
=Clear Value
LED Stage Light
Lost DMX
=Hold Value
LED Stage
Light
Advanced
LED Stage Light
Access Code
LED Stage Light
Access Code
Code = 000
Code = 008
LED Stage Light
Adjust
LED Stage Light
Adjust
Pan
LED Stage Light
Adjust
Pan = +000
LED Stage Light
Adjust
Prism
LED Stage Light
Adjust
Prism = +000
LED Stage Light
Adjust
Focus
LED Stage Light
Adjust
Focus = +000
LED Stage Light
LED Stage Light
LED Stage Light
Temperature
=025C
LED Stage Light
LED Stage Light
Fixture Ho urs
=00000 H
LED Stage Light
Reset Hours
=NO
LED Stage Light
Reset Hours
=YES
LED Stage Light
LED Stage Light
Product ID
= Y************
LED Stage Light
LED Stage Light
View DMX
Value Channel
001 = 000
LED Stage Light
LED Stage Light
Version
=1.00F
LED Stage Light
LED Stage Light Load
De faults
LED Stage Light Load
De faults

Premier150 Spot Eternal Lighting Feb 2016
LED Stage Light
Adjust
Tilt
LED Stage Light
Adjust
Tilt = +000
LED Stage Light
Adjust
Red
LED Stage Light
Adjust
Red = +000
LED Stage Light
Adjust
Green
LED Stage Light
Adjust
Green = +000
LED Stage Light
Adjust
Blue
LED Stage Light
Adjust
Blue = +000
LED Stage Light
Adjust
White
LED Stage Light
Adjust
White = +000
LED Stage Light
Adjust
Fixed Gobo Whee l
LED Stage Light
Adjust
Fixed Gobo = +000
Level 1 Level 2 Level 3 Level 4
LED Stage Light
Adjust
Rot. Gobo Whe el
LED Stage Light
Adjust
Rot. Gobo = +000
LED Stage Light
Adjust
Prism
LED Stage Light
Adjust
Prism = +000
LED Stage Light
Adjust
Focus
LED Stage Light
Adjust
Focus = +000
LED Stage Light
Information
LED Stage Light
Temperature
LED Stage Light
Temperature
=025C
LED Stage Light
Fixt ure Hours
LED Stage Light
Fixt ure Hours
=00000 H
LED Stage Light
Reset Ho urs
=NO
LED Stage Light
Reset Ho urs
=YES
LED Stage Light
Product ID
LED Stage Light
Product ID
= Y************
LED Stage Light
View DMX Value
LED Stage Light
View DMX Value
Channe l 001 = 000
LED Stage Light
Versio n
LED Stage Light
Versio n
=1.00F
LED Stage Light
Load Defaults
LED Stage Light
Load Defaults
=NO
LED Stage Light
Load Defaults
=YES
Note:

Premier150 Spot Eternal Lighting Feb 2016
Only one Pro je ctor to be set as a Master in a signal Cab le. If a Master is in use, P lease disab le
DMX control signal.
When multiple projectors’ work together in synchronous contro l state, Parameters can be
transmitted from the master pro jector to the slave projectors such as DMX channel mode,
Displa y setting sta tus and operation mode (User memory data is included). Before
parameter s transmitted, th e pro jector which will send parameters should be set as a Master
and other s set as Slaves.
DMX Protocol
Mode/Channel
FUNCTION VALUE DESCRIPTION
Short mode
Standard
mode
Extended
mode
1
1
1
Pan
0~255
Pan Moving 0 - 540 Degree
2
2
Pan Fine
0~255
Pan Fine Moving
2
3
3
Tilt
0~255
Tilt Moving0 - 270 Degree
4
4
Tilt Fine
0~255
Tilt Fine Moving
5
5
Move Speed
0~255
Moving Speed From Fast To Slow
3 6 6 Dimmer
0~9
Shut Off (0%)
10~255
Line Dimmer
4
7
7
Strobe
0~4
No Strobe
5~9
No strobe (OPEN)
10~199
Cycle strobe from Slow To Fast
200~204
No strobe (OPEN)
205~224
Random strobe from Slow To Fast
225~229
No strobe (OPEN)
230~249
Random color strobe from Slow To Fast
250~255
No strobe (OPEN)
5
8
8
Red
0~255
8 Bit Red
9
Red Fine
0~255
16 Bit Red
6
9
10
Green
0~255
8Bit Green
11
Green Fine
0~255
16 Bit Green
7
10
12
Blue
0~255
8 Bit Blue
13
Blue Fi ne
0~255
16 Bit Blue
8
11
14
W hite
0~255
8Bit White
15
White Fine
0~255
16 Bit White
12
16
Virtual Color
0~9
No Function
10~19
Colour Temperat ure 2700K (R=255, G=168, B=0,
W =255)
20~29
Colour Temperat ure 3200K (R=255, G=180, B=0,
W =255)
30~39
Colour Temperat ure 4200K (R=247, G=214, B=19,
W =255)
40~49
Colour Temperat ure 5600K (R=217, G=251, B=50,
W =255)
50~59
Colour Temperat ure 8000K (R=168, G=255, B=84,
W =255)
60~69
Red Color (R=255, G=0, B=0, W=0)
70~79
Orange Color (R=255, G=97, B=0, W =0)
80~89
Green Color (R=0, G=255, B=0, W=0)

Premier150 Spot Eternal Lighting Feb 2016
Mode/Channel
FUNCTION VALUE DESCRIPTION
Short
mode
Standard
mode
Extended
mode
12
16
Virtual Color
90~99
Blue Color (R=0, G=0, B=255, W=0)
100~109
Yellow Color (R=255, G=255, B=0, W=0)
110~119
Cyan Color (R=0, G=255, B=255, W=0)
120~129
Magenta Color (R=0, G=255, B=255, W=0)
130~139
White Color (R=255, G=255, B=255, W=255)
140~255
Virtual Color Rainbow
9
13
17
RotationGobo
Wheel 1
0~9
White (No Gobo)
10~19
Gobo 1
20~29
Gobo 2
30~39
Gobo 3
40~49
Gobo 4
50~59
Gobo 5
60~69
Gobo 6
70~79
Gobo 7
80~89
Gobo 1 From Slow To Fast
90~99
Gobo 2 From Slow To Fast
100~109
Gobo 3 From Slow To Fast
110~119
Gobo 4 From Slow To Fast
120~129
Gobo 5 From Slow To Fast
130~139
Gobo 6 From Slow To Fast
140~149
Gobo 7 From Slow To Fast
150~202
Forw ardRotationEffect From Fast To Slow
203~255
Forw ardRotationEffect From Slow To Fast
10 14 18 Gobo 1
Rotation
0~127
Gobo Index
128~190
Gobo Forw ard RotationFrom Fast To Slow
191~192
Stop Rotation
193~255
Gobo Reverse RotationFrom Slow To Fast
11 15 19
Gobo Wheel 2
0~9
White (No Gobo)
10~19
Gobo 1
20~29
Gobo 2
30~39
Gobo 3
40~49
Gobo 4
50~59
Gobo 5

Premier150 Spot Eternal Lighting Feb 2016
11
15
19
Gobo Wheel 2
60~69
Gobo 6
70~79
Gobo 7
80~89
Gobo 1 From Slow To Fast
90~99
Gobo 2 From Slow To Fast
100~109
Gobo 3 From Slow To Fast
110~119
Gobo 4 From Slow To Fast
120~129
Gobo 5 From Slow To Fast
130~139
Gobo 6 From Slow To Fast
140~149
Gobo 7 From Slow To Fast
150~202
Forw ardRotationEffect From Fast To Slow
203~255
Forw ardRotationEffect From Slow To Fast
12
16
20
Gobo 2
Rotation
0~127
Gobo Index
128~190
Gobo Forw ard RotationFrom Fast To Slow
191~192
Stop Rotation
193~255
Gobo Reverse RotationFrom Slow To Fast
13 17 21 PrismInsertion
0~127
PrismExcluded
128~255
PrismInserted
14
18
22
Prism Rotation
0~127
0 - 540 Angle Degree
128~190
Forw ard Rotation from Fast to Slow
191~192
Stop
193~255
Reverse Rotationfrom Slow to Fast
15
19
23
Focus
0~255
Line Focus
16
20
24
Call Program
0~50
No Function
51~100
Preset Program1
101~150
Preset Program2
151~200
Preset Program3
201~255
Preset Program4
17
21
25
Function
"Stay in acertain
va lue for m or e t han 5
sec onds"
0~24
Unused
25~49
Reset: Effects
50~74
Unused
75~99
Reset: Pan Tilt
100~124
Unused
125~149
Reset: Complete
150~174
Unused
175~199
Unused
200~224
Unused
225~255
Unused