Ethos IS100 User manual

ETPD0122 rev.5
Page 1 of 6
Installation instructions for the
Ethos IS100 wood fire with a
Zero Clearance Cabinet and
Econ-Air flue system
Retain these instructions for future reference
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz

ETPD0122 rev.5
Page 2 of 6
Following these instructions allows for the Ethos IS100 wood fire
to be safely installed in a timber frame wall without the need for
further heat protection past that supplied as part of the Zero Clearance
Cabinet and the Econ-Air flue system (see notes regarding installation
on combustible surfaces).
WARNING: It is critical that these instructions are followed fully and
that no substitute parts are used.
INSTALLATION NOTES
1. Combustible materials must be kept a minimum of 25mm away from
all parts of the Zero Clearance Cabinet and the diameter 250 liner.
2. Adequate ventilation must be available for cooling the Zero Clearance
Cabinet - see installation diagram for supplied ventilation plate
mounting detail (page# 5).
3. Ethos insulation base panel (part# ZC1140) is required below the Zero
Clearance Cabinet when in direct contact with combustible materials
such as timber flooring (refer to page# 3 for further detail).
Econ
-
Air flue system parts list:
3
130mm x 1200mm S/S flue
1
130mm x 600mm S/S flue
2
200mm x 1200mm galv. liner
1
200mm x 600mm galv. liner
1
200mm x 1200mm galv. liner with ‘Z’ brackets
3
250mm x 1200mm galv. liner
1
250mm x 600mm galv. liner
4
40mm x 40mm x 600mm mounting rails
1
130mm spider bracket
1
Ethos IS cowl base (EXS
-
12002)
1
Ethos revolving cowl (EXS
-
12010)
These instructions should be read in conjunction
with the instruction documents supplied with your
Ethos IS100 wood fire
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz

ETPD0122 rev.5
Page 3 of 6
Floor Insulation Detail
The table sets out the calculated floor protector projections required to
ensure that temperatures on the exposed floor comply with the requirements
of the AS/NZS 2918:2001 for exposed floors constructed of medium heat
resistant materials.
H
=
H
e
i
g
h
t
o
f
t
o
p
o
f
H
e
a
r
t
h
above Exposed Floor (mm) P = Projection (mm)
0 560
35 488
50 432
75 385
100 343
125 310
135 300
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz

ETPD0122 rev.5
Page of 6
The Econ-Air flue system recovers the vented heat from the
Zero Clearance Cabinet and recycles it back into the stove
as combustion air for added efficiency.
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz

ETPD0122 rev.5
Page 5 of 6
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz

ETPD0122 rev.5
Page 6 of 6
It is essential to provide
adequate ventilation to the
cavity. Mount supplied
ventilation plates centrally and
as low as the timber frame will
allow. Ensure cavity has access
to uninterrupted air supply.
Vent plates mounting detail
Capisco Limited, PO Box 938, Whangaparaoa, Auckland 0930 - Email: [email protected] - www.ethosfires.co.nz