Leenders Sorenne User manual

SORENNE
INSTALLATION EN

SORENNE LEENDERS
201951.000.I.EN
Points of aenon installaon Sorenne
Required tools
Transport
• Remove the 2 bolts that secure the Sorenne to the pallet.
• Remove the door: open the door and li it o the hinges.
• Take and transport with the hand truck at the front. Place protecon between the hand truck
and the Sorenne to prevent damage.
10
1
3
1
2
3
2
10 30

SORENNE LEENDERS
201951.000.I.EN
Fresh air supply (oponal)
• Place compriband under the base.
• The compriband then expands.
• Mount cover plate later.
Level
• Oponally set 4 feet.
Swivelling base (oponal)
• Remove transport block (4x).
4
5
6
30
5
4
6
10

SORENNE LEENDERS
201951.000.I.EN
Swivelling base (sequel)
• If swivelling by 120°: place one of the screws
of the transport block as shown in the
drawing.
Fresh air supply (sequel)
• Place the cover plate. Place three of the
screws of the transport block.
Assembling the foot
• Fold the shroud around the foot.
• Posion the shroud using the notches at the
rear.
• Secure both brackets.
• Please note: ensure that the air slide can
move freely and the strip does not touch the
ground.
7
8
9
8
9
7
10
10

SORENNE LEENDERS
201951.000.I.EN
Plus stoneset (oponal)
• Place both stones. Remove any rubble.
Door
• Carefully place the door in both hinges.
Self-closing door (oponal)
• Mount the spring on the hinge.
Interior inspecon
Parts of the re chamber can shi during transport. To prevent this, the heat shield and air pipes
are secured with a small amount of silicone sealant. Check to see if these are sll secured.
Inspecon
Pay close aenon to the following points aer installing the Sorenne:
• Check that the Sorenne stands securely on its base.
• Make sure that no combusble and/or explosive items (paper, cardboard, spray cans, etc.)
have been le in or close to the Sorenne.
• If the ue pipe is in working condion, check operaon of the ue and the air supply to the
Sorenne by lighng a re. Follow the instrucons in the manual.
11
11
10
10

SORENNE LEENDERS
201951.000.I.EN
General instrucons and regulaons
Installaon
To secure the warranty, the Warne must be installed by a properly qualied person employed by a
dealer recognized by Harrie Leenders Haardkachels. See leenders.nl for a current list of addresses of
recognized dealers or contact the manufacturer.
The stove is suscepble to scratching. Handle with care.
Aer installaon, check the draught by burning some kindling wood.
Use
• All local regulaons including those referring to naonal and European standards must be
observed when installing the appliance.
• Ensure there is sucient venlaon/air supply in the room where the stove is installed.
Air extractors such as a cooker hood may cause problems due to ue gases escaping from the
stove into the room.
• The appliance is not suitable for a shared ue system.
• The appliance must be installed on a oor having sucient bearing capacity.
• Ensure adequate access for cleaning the appliance, the ue-gas connecon and the chimney.
Safety instrucons
• Glass is quite suscepble to breaking and broken glass is quite sharp. Take appropriate measures.
• For general safety, we refer to the VCA guidelines.
• Note: Aer installaon, ensure there is no inammable and/or explosion-hazardous material in or
on the stove such as a spray can, packing material and the like.
Distance to combusble materials
• Back; 20 cm
• Side; 20 cm
• Front; 85 cm
Specicaons Sorenne
• Nominal power = 7.4 kWh
• Flue gas mass ow = 7.9 g/s
• Appliance weight = 163 kg
• Minimum chimney draught = 0,115 mbar
• Flue gas temperature directly over the stove = 271 °C
• Energy Eciency 77.2%, class A, index 102,9
A