eufy Security FLOODLIGHT CAM 2 PRO User manual

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo
are trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005002819

QUICK START
GUIDE
EUFY FLOODLIGHT CAM 2 PRO

English 01
Deutsch 27
Español 49
Français 73
Italiano 97
Nederlands 121
Portuguese 145
 169

EN 001
Table of Contents
SAFETY INSTRUCTIONS 02
WHAT'S IN THE BOX 02
PRODUCT OVERVIEW 03
DECLARATIONS 04
POWERING ON YOUR FLOODLIGHT CAMERA 06
SETTING UP THE FLOODLIGHT CAMERA 07
PREPARING FLOODLIGHT CAMERA FOR INSTALLATION 08
INSTALLING THE JUNCTION BOX 09
MOUNTING YOUR FLOODLIGHT CAMERA 12
ADJUSTING THE LIGHTING ANGLE 21
NOTICE 24

002 EN
SAFETY INSTRUCTIONS
• Disconnect power at the fuse or circuit breaker before installing.
• Do not install the product near flammable surfaces.
• To avoid risk of shock, injury or death, always be cautious when working
with electricity.
• Consult a licensed electrician if you are uncomfortable working with
electrical wiring.
• Make sure the Floodlight Camera is properly grounded.
• Floodlight Camera must be installed on a wall and on a UL-listed junction
box.
WHAT'S IN THE BOX
eufy Floodlight Cam 2 Pro
(T8423)
Charging Cable
Central Screw Central Screw Cap Plate Screws Junction box
Installation Hook
& String

EN 003
Required (not included):
USB Power Adapter
(5V/1A)
Power Drill
(15/64 mm)
Crosshead
Screwdriver
PRODUCT OVERVIEW
Floodlight
Speaker
System Indicator
Cam Component
Infrared Component
Light Adjustment Knob
Mounting Base
Tilt Adjustment Slide Block
SYNC Button / USB Port
Motion Sensor Component

004 EN
DECLARATIONS
IP65-rated dustproof and waterproof
This product meets IP65 (dustproof and waterproof) requirements.
For dustproof testing, the product was vacuumed and placed in a dust box.
After 8 hours of testing, no dust was found in the product.
For waterproof testing, the product was sprayed by a nozzle with an inner
diameter of 6.3mm, and water flow of 12.5 L/min. After the test, the product
operated normally with no water found inside.

EN 005
Anti-corrosion
The metal surface of the product is galvanized, and can survive continuous
exposure to salt spray at 35 ° C +/- 2 ° C (relative humidity: 90%-95%) with a
salt concentration of 5% NaCl for 48 hours in the salt spray test.
Load-bearing tests
The L-shaped bracket and center screw of the product are made of SUS304
steel and have passed industrial-grade outdoor reliability and durability tests.
NOTE: The total weight of the product is 2.2kg (4.9lbs), and the L-shaped
bracket and center screw is strong enough to carry a load of 10kg (22lbs).
10kg

006 EN
POWERING ON YOUR FLOODLIGHT CAMERA
To avoid scratching the Floodlight Camera, do not peel off the
protective film for the time being.
Put your Floodlight Camera in the direction as illustrated on a table, and open
the USB port cover. Connect the device to a power source inside your home
using the micro USB charging cable and a power adapter (5V/1A, not provided).
Wait 1 minute or until the LED indicator blinks red.
The Floodlights will only light up when in wired power mode. The
USB-powered connection is used for setting up the camera safely
inside your home.

EN 007
SETTING UP THE FLOODLIGHT CAMERA
Push and hold the button to open the mounting base and find a QR Code.
Download the eufy Security app from the App Store (iOS devices) or Google
Play (Android devices).
Log in or sign up for a eufy Security account, then follow the on-screen
instructions to complete the setup.

008 EN
Make sure you can livestream video from Floodlight Camera
before mounting.
If the Floodlight Camera LED keeps blinking red, it means the floodlight
is not connected to the Internet. Please make sure the Wi-Fi signal is
strong at the desired location. You may consider moving the wireless
router closer to Floodlight Camera or using a Wi-Fi range extender.
PREPARING FLOODLIGHT CAMERA FOR
INSTALLATION
1. Unplug the power adapter. Close the mounting base and USB port cover.
2. Shut down the circuit breaker in your house. Switch on/off the lights to
make sure the electricity in your house is properly shut off.

EN 009
To avoid risk of shock, injury or death, always be cautious when
working with electricity.
INSTALLING THE JUNCTION BOX
1. Remove the rubber plugs indicated in the illustration below.

010 EN
2. Run the existing wire through the hole.
If you don’t have existing wires outdoors, contact a licensed
electrician to run the wires.
3. Install the junction box:
• Orient the two mounting holes vertically to ensure stable mounting.
• On wooden walls, DO NOT pre-drill holes. Use the screws provided to
fix the junction box onto the wall.

EN 011
• On walls that are made out of hard materials, such as stucco, brick, or
concrete, drill holes with a 15/64 inch (6 mm) drill bit, and then insert
the anchors provided into the holes. Use the screws provided to fix
the junction box on the wall.
1 2
4. Unscrew the bolt with a flat-head screwdriver. Connect the Neutral (blue)
/ Ground (green / green and yellow) / Live (brown) wire to the Neutral /
Ground / Live wire connector in the junction box respectively. Secure the
wires tightly to prevent wires from falling.
N
L
Neutral
Ground
Live
1 2

012 EN
MOUNTING YOUR FLOODLIGHT CAMERA
To ensure the best motion detection range, we recommend in-
stalling the Floodlight Camera within 2-3 meters of the ground.
You can hang Floodlight Camera upside down or install it vertically on the
wall. Select the installation method that best suits the position of your
junction box.
Wall Mount
Upside-down Mount

EN 013
Mount Floodlight Camera onto a Wall
STEP 1. Before Mounting
1. Pass the hook through the other end of the string as illustrated.

014 EN
2. You need a ladder to mount your Floodlight Camera on the wall. Make
sure you do not place your ladder right under the Floodlight Camera. Place
it to the lower left or right of the Floodlight Camera as illustrated below to
avoid obstructing your view while mounting.

EN 015
3. Screw part of the central screw through the center of the Junction box
and leave the screw long enough to hang the Floodlight Camera using the
provided hook.
STEP 2. Connect Wires
1. Connect the ground wire from the Floodlight Camera to the ground wire
from the wire connector in the junction box.

016 EN
2. Connect the live / neutral wire from the Floodlight Camera to the live /
neutral wire from the wire connector in the junction box respectively.
N
L
Neutral
Ground
Live
3. Secure the wires with a screwdriver.
4. Hold the Floodlight Camera, and remove the hook, strings, and central
screw from the junction box.
box.
•If you have problems with the proper operation of Flood-
light Camera, consult a licensed technician.
•Green / green and yellow, brown and blue wires must con-
nect to the matching colors. Never cross connect.

EN 017
STEP 3. Mount the Floodlight Camera
1. Press the button to open the mounting base.
2. Hold the mounting base, and insert the central screw through the center
of the mounting base and screw it tightly. Use the central screw cap to
cover the central screw to prevent it from rusting.
3. Cover the central screw with the provided cap.