EUFY T8321-C User manual

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[e-mail]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[e-mail]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[e-mail]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[e-mail]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[e-mail]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[email protected]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[email protected]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[email protected]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

01 02 03 04 05 06 07 08
USER MANUAL
Video Baby Monitor 720P
WHAT’S IN THE BOX
Welcome Card
Welcome Card
Welcome Card
Welcome Card
Video Baby Monitor 720P
Model: T8321-C
FCC ID:2AOKB-T8321C
IC:23451-T8321C
Monitor Micro-USB
Power Cable (1 m)
Monitor Adapter (5V
2A)
Welcome Card
Video Baby Monitor 720P
Model: T8321-M
FCC ID:2AOKB-T8321M
IC:23451-T8321M
Camera Micro-
USB Power Cable
(3 m)
Mounting Screws
Wall Mount
Camera Adapter
(5V 1A)
User Manual
Note: Power adapter varies by region.
FEATURE INTRODUCTION
Monitor Features
1 2
4
3
5
6
7
8
9
10 11 12
13
1Screen 6LED indicator
2Menu button • Red: charging
• White: Fully charged
3Navigation button
4OK button 7Micro USB charging port
• Press to confirm the selection
• Press to switch camera display if more
than 2 cameras added
8Volume down
9Volume up
10 Power button
5Return to previous level of menu / Talk
button 11 Zoom button
• Press and hold to speak to the camera
• When menu is opened, press to return
to the previous level of menu
12 Reset
13 Speaker
Camera Features
1
2
3
4
5
6
7
1Microphone 5Pairing button
2Standard camera lens 6Micro USB port
3LED indicator 7Speaker
4Temperature sensor
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use.To charge:
1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power
adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.
5V/2A
Charge the Camera
1. Connect one end of the micro USB cable to the baby camera, and the other end to the power
adapter (5V 1A).
2. Plug the power adapter into a power outlet.
5V/1A
The new baby monitor and camera will set up automatically.You are all set to use the products after
the monitor and camera are fully charged.
ADDING A NEW BABY CAMERA TO THE
BABY MONITOR
The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the
following steps when adding extra baby cameras or after resetting a baby camera.
1. Enter menu settings, go to Camera Add Camera, then follow the onscreen instructions
to start the pairing.
Add Camera
Delete Camera
Cycle Cameras
Camera Settings
60 Secs
Scanning for new camera
Push the button on the
camera to pair.
1Secs
4
23o
c
06 12 AM
:
2. Press and hold the pairing button on the rear of the camera for 1 second until a notication
prompt is heard.
3. Check the rmware version of the monitor (see image below) to make sure your baby monitor
and camera are running the same, latest rmware version.
Language
Anti-Screen Flicker
Default Settings
Temperature Unit
Sleep Mode
Connect with Us
Night Vision Mode
Time Set
4
06 12 AM
:
Monitor: v x.x.x
Camera: v x.x.x
SN: T8300E0A18370E72
https://www.eufylife.com
United States [phone]
United Kingdom [phone]
Germany [phone]
Japan [phone]
[email protected]
To check whether it is the latest version:
1Visit the website below:
https://www.eufylife.com/support/5505/spaceview-baby-monitor
2 If the rmware version is lower than the version shown online (highlighted in green), click the
firmware version to download. The downloaded file includes firmware for both T8300 and
T8321 models, make sure you use the T8321 rmware.
3Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware
Upgrade Manual to complete rmware upgrade.
Note: ●The eufy Security Spaceview baby camera can be added to the monitor. Before adding
the camera, make sure SpaceView baby camera is running the same, latest version
with the monitor’s.
• Chrome OS is not supported for rmware upgrade.
• Before you upgrade rmware, use the provided micro USB cable (1m) to connect the
device needed to your computer.
USING THE BABY MONITOR
When more than 2 cameras are added to the monitor, you can manually switch among cameras by
pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected
camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected
baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.
MOUNTING THE BABY CAMERA ON THE
WALL
1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw
holes with a pencil.
UP
2. Drill 5
1'' holes into the wall and then insert anchors into the holes.Anchors are not needed for
wooden walls.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
UP
4. Snap the baby camera onto the wall mount.
UP

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: suppor[email protected]
@EufyOfficial
@EufyOfficial
eufyofficial

09 10 11 12 13 14 15
5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250°
horizontally) manually, as pan and tilt functions are not supported on this model when using the
navigation button.
72 °F
60°
25°
250°
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu
Settings.
Menu Settings
Menu Options Description
Brightness Set the brightness of the screen.
Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off.
Sound Alert
You can set the baby monitor to alert you when a specific noise level is
detected.
Note: Surrounding noise might set off false alarm.
Lullaby
Select your desired lullaby song. You can adjust the volume by selecting the
volume button.
Note: Sound Alert is automatically disabled when Lullaby function is
enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom Zoom in / out
Menu Options Description
Alarm
• Set alarm on / off
• Specify the duration when the alarm will sound
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera
Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset
intervals.
Time Set Set the time on the monitor.
Night Vision Mode
When Auto is enabled, the camera will change the screen color according
to the light conditions in the room. When disabled, the camera will
stick to daylight screen color and will not change when the surrounding
environment is getting dark.
Note: We recommend setting this function to On for most of the
situations.
Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering.
Language Sets the on-screen display menu language.
Default Settings Resets all options to their default setting.
Temperature Unit Select your desired temperature measure unit.
Connect with Us Contact details
Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts
during this interval, even if the conditions are met to trigger an alert.
406 12 AM
:
Brightness
On-screen Menu Icons
Icon Icon Description
Wireless signal strength
Night Vision Mode is enabled
1
Shows the camera that is currently presenting on the baby monitor screen
Note: This icon will not appear on the screen when there is only one camera
connected to the monitor.
Cycle Cameras enabled
Sound Alert enabled
Sound level of the room the camera is in
08:30 AM Current time
Current battery level of the baby monitor
72 °F Current operating temperature
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of
children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC
Adapters provided.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of
conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of
version 2.0 or higher. The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the
Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C.
The suitable temperature for T8321-C and accessories is -20°C-40°C.
When charging, please place the device in an environment that has a normal room temperature and
good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from
5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may
cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The
plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc /
1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and the human body. To maintain compliance with RF
exposure requirement, use product that maintain a 20cm distance between the device and human
body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm
(EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept
0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been
tested against this SAR limit. The highest SAR value reported under this standard during product
certication for use at the limb is 0.310W/kg. This device was tested for typical hand held
operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be
used in xed exposure condition. RF exposure information: The Maximum Permissible Exposure
(MPE) level has been calculated based on a distance of d=20 cm between the device and the human
body.To maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be
delivered to an appropriate collection facility for recycling. Proper disposal and recycling
helps protect natural resources, human health and the environment. For more information
on disposal and recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for
help.
FCC Radio Frequency Exposure Statement
The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can
be used in xed exposure condition. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg
Worn on body will have unexpected RF exposure RISK.
FCC ID (for T8321-C): 2AOKB-T8321C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: [phone]
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product(T8321-C), maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm
from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Hand held is 4.0W/kg.
Device is recommended to use in hand held only and SAR when hand held is 1.796 W/kg. Worn on
body will have unexpected RF exposure RISK.
Ce T8321-M a été testé pour des opérations typiques portées avec le dos du combiné à 0 mm du
corps.
Informations sur l'exposition aux RF (SAR)
La limite SAR d'extrémité de la FCC pour les appareils portatifs est de 4,0 W / kg.
Il est recommandé d'utiliser l'appareil uniquement en mode portatif et le DAS lorsque celui-ci est
de 1,796 W / kg. Le corps porté aura un RISQUE d'exposition inattendue aux RF.
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries.All other
trademarks are the property of their respective owners.
51005002167 V02
CUSTOMER SERVICE
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Warranty
12-month limited warranty
Call Us
United States [phone] Mon-Fri 9AM-5PM (PT)
United Kingdom [phone] Mon-Fri 6AM-11AM (GMT)
Germany [phone] Mon-Fri 6:00-11:00
Email Us
Customer Support: [e-mail]
@EufyOfficial
@EufyOfficial
eufyofficial