EUFY S220 SoloCam User manual

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
su[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

01 02 03 04 05 06
QUICK START GUIDE
S220 SoloCam
PRODUCT OVERVIEW
①
④
⑤
⑥
⑦
②
⑧
⑨
③
⑩
T8134 S220 SoloCam
①Solar Panel ⑥Motion Sensor
②Photosensitive Sensor ⑦Speaker
③Microphone ⑧SYNC Button
④Camera Lens ⑨USB-C Charging Port
⑤LED Indicator ⑩Mounting Hole
CHARGING SOLOCAM
LED Indicator
SETTING UP SOLOCAM
Download the App and Set Up the Device
1. Download and install the eufy Security app, and sign up for an
account.
2. Follow the on-screen instructions to add your SoloCam.
Charging Solid Blue
Fully Charged Off
MOUNTING SOLOCAM
Select a Location
S220 SoloCam can be mounted on a wall. Select a location where
it achieves the desired view. We recommend mounting it 7-10 ft
(2-3 m) above ground level.
To maximize the solar panel efficiency, select a location
where S220 SoloCam receives plenty of sunlight.
Motion
Detection
Zone
Camera Field
of View
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
10°
Mount S220 SoloCam
S220 SoloCam can be mounted both indoors and outdoors.
1. Loosen the cover of the mount by turning it counterclockwise
and disassemble the mount.
2. This step applies if mounting onto hard surfaces such as brick
or concrete. For soft surfaces such as wood, skip this step.
Drill holes with a 15/64 in (6 mm) drill bit, then insert the anchors
into the holes.
3. Firmly screw the base of the mount onto the wall. Reassemble
the mount.
4. Screw SoloCam onto the mount. Ensure the solar panel is
facing the sky. Position SoloCam to achieve the desired view,
checking it using the live stream in the eufy Security app.
For troubleshooting, check the Help section in the eufy
Security app.
CUSTOMER SERVICE
12-month limited warranty
(US) [phone]
(UK) [phone]
(DE) [phone]
(中国 ) [phone]
(日本 ) [phone]
(AU) [phone]
(Egypt) [phone]
(UAE) [phone]
(Kuwait) [phone]
(Saudi Arabia) [phone]
(Middle East & Africa) [phone]
[email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial @EufyOfficial @EufyOfficial

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.

07 08 09 10 11
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition. The min
separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: [phone]
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps
afin de vous conformer aux exigences en matière d'exposition RF.
Declaration of Conformity
This product complies with the radio interference requirements of
the European Community.
This product complies with the radio interference requirements of the
European Community.
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. For the declaration of conformity, visit the Web
site: https://uk.eufylife.com/.
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.
Wi-Fi Operating Frequency Range: 2412~2472MHz;
Wi-Fi Max Output Power:19.65 dBm
The following importer is the responsible party (contact for EU matters
only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
This product complies with the radio interference requirements of
the United Kingdom
Hereby, Anker Innovations Limited declares that this product is in
compliance with Radio Equipment Regulations 2017(SI2017/1206). The
full text of the UK declaration of conformity is available at the following
internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as
household waste and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling help
protect natural resources, human health, and the environment.
For more information on the disposal and recycling of this product,
contact your local municipality, disposal service, or the shop where
you bought this product.
Attention:
-Le remplacement d’une batterie par un type incorrect peut contourner les
protections et créer un danger ;
-L’élimination d’une pile dans un feu ou une autre source de chaleur
importante, ou par écrasement ou découpage, peut entraîner une
explosion ainsi qu’une fuite de liquides et de gaz inflammables ;
-Le fait de laisser une batterie dans un environnement extrêmement
chaud peut entraîner une explosion ainsi qu’une fuite de liquides et de gaz
inflammables ;
-Une batterie soumise à une pression d’air extrêmement faible peut
provoquer une explosion ainsi qu’une fuite de liquides et de gaz
inflammables.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005003795 V01
SAFETY
The recommended temperature range for devices and accessories is -20°C
to 50°C (-4°F - 122°F).
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, do not use this device in an environment that exceeds
the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or
instruction manual, avoid exposing your device to direct sunshine or
excessively wet environments.
It is recommended to supply the device in an environment with a
temperature that ranges from 5°C ~ 25°C.
When supplying, please place the device in an environment that has a
normal room temperature and good ventilation.
CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.
ATTENTION!
IL EXISTE UN RISQUE D’EXPLOSION EN CAS D’UTILISATION D’UN TYPE DE
PILE INCORRECT.ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.
Warning:
– Replacing a battery with an incorrect type may bypass safeguards and
create danger;
– Disposal of a battery in a fire or other source of significant heat, or
by crushing, or cutting, may result in an explosion as well as leakage of
flammable liquids and gases;
– Leaving a battery in an extremely hot environment may result in an
explosion as well as leakage of flammable liquids and gases;
– A battery subjected to extremely low air pressure may result in an
explosion as well as leakage of flammable liquids and gases.