EURO EV600DFSX User manual

USAGE AND
CARE GUIDE
PRODUCT CODE:
cooking
EV600DFSX

Thank you for choosing us! Please read all instructions before using
this appliance. This book contains valuable information about
operation, care and service. Keep it in a safe place for future
reference. Should the appliance be sold or transferred to another
owner, or should you move house and leave the appliance, always
ensure that the book is supplied with the appliance so that the new
owner can be acquainted with the functioning of the appliance and
relevant warnings. Important
Safety Warning
THESE WARNINGS ARE PROVIDED IN THE INTEREST OF
SAFETY, PLEASE READ THEM CAREFULLY BEFORE INSTALLING
OR USING THE APPLIANCE
To maintain the EFFICIENCY and SAFETY of this appliance, we
commend:
Call the Service Centers authorized by the store where you buy
the cooker.
Always use original Spare Parts
1. This appliance is intended for non-professional use within the
home.
2. Before using the appliance, read the instructions in this owner’s
manual carefully, since you should find all the instructions you require
to ensure safe installation, use and maintenance. Always keep this
owner’s manual close to hand since you may need to refer to it in the
future.
3. After removing the packaging, check that the appliance is not
damaged. If you have any doubt, do not use the appliance. Contact
your nearest Service Centre of the store where you buy the appliance.
Never leave the packaging components plastic bags ，foamed
polystyrene， nails, etc. ) within the reach of children since they are a
source of potential danger.
4. The appliance must be installed only by a qualified person in
compliance with the instructions provided. The manufacturer declines
all responsibility for improper installation which may harm persons and
animals and damage property.
6. The electrical safety of this appliance can only be guaranteed if the
cooker is correctly and efficiently earthed, in compliance with current
regulations on electrical safety. Always ensure that the earthing is
efficient if you have any doubts call in a qualified electrician to check
the system. The manufacturer declines all responsibility for damage
resulting from a system which has not been earthed.
2
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
5.

7. Check that the electrical capacity of the system and sockets will
support the maximum power of the hob, as indicated on the rating
label. If you have any doubts call in a qualified technician
8. When the cooker is first used an odor may be emitted, this will
cease after a period of use. When first using the cooker ensure that
the room is well ventilated e.g., open a window or use an extractor fan
and that persons who may be sensitive to the odor avoid any fumes. It
is suggested that any pets be removed from the room until the smell
has ceased. This odor is due to temporary finish on oven liners and
element sandal so any moisture absorbed by the insulation.
9. Ensure that the appliance is switched off before maintenance by
switching off the main switches and turning all knobs to OFF position.
10. The openings and slots used for ventilation and dispersion of heat
on the rear and below the control panel must never be covered.
11. The user must not replace the supply cable of this appliance.
Always call an after-sales servicing Centre authorized by the seller in
the case of cable damage or replacement.
12. This appliance must be used for the purpose for which it was
expressly designed. Any other use is considered to be improper and
consequently dangerous. The manufacturer declines all responsibility
for damage resulting from improper and irresponsible use.
13. A number of fundamental rules must be followed when using
electrical appliances. The following are of particular importance do not
touch the appliance you’re your hands or feet are wet do not use the
appliance bare footed. Never allow the Mains Cable to be stretched,
pulled or damaged if the Cooker is moved for cleaning etc. Do not use
the cooker if the Mains Cable is damaged, consult a qualified
electrician. Do not allow the cooker to be used unsupervised by
children or persons unfamiliar with it.
14. Always switch off the electrical supply to the cooker and allow it to
cool down before carrying out any cleaning operations etc.
15. Danger of fire: do not store items on the cooker surfaces.
16. To avoid accidental spillage do not use cookware with uneven or
deformed bottoms on the burners or on the electric plates.
17. Special care should be taken when using chip pans etc. in order to
avoid splashing or spillage of hot oil. They should not be used
unattended since over heated oil may boil over and could also ignite.
18. Parts of this appliance, cooking surfaces, retain heat for
considerable periods after switching off. Care should, therefore, be
taken when touching these areas before they have completely cooled
down.
19. Never use flammable liquids such as alcohol or gasoline, etc. near
the appliance when it is in use.
20. When using small electrical appliances near the hob, keep the
supply cord away from the hot parts.
3
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
WARNING: Accessible parts may become hot during use. Young
children should be kept away

21. Make sure the knobs are in its “OFF” position when the appliance
is not in use. Also make all potentially dangerous parts of the
appliance, safe, above all for children who could play with the
appliance.
22. When the appliance is in use the heating elements and some parts
of the oven door become extremely hot. Make sure you don’t touch
them and keep children well away.
23. If you use the power cable for single phase, the minimum
cross-sectional area is 10mm2. For three phases the minimum cross
sectional area is 2.5 mm²
24.You must grill with closed door.
25. DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
26. DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
27. DO NOT MODIFY THIS APPLIANCE.
28. DO NOT USE THIS APPLIANCE AS A SPACE HEATER.
29. Gas installation must be made in accordance with AS/NZS 5601.
Also refer to rangehood manufacturers recommendation.
30. Special conditions which shall be avoided, e.g. marine
environment, and any conditions necessary to ensure optimum
performance.
31. Where necessary, a safe purge before the appliance is re-lit.
Safety
For the user and installer
1. Disconnect the range before cleaning or doing maintenance.
2. Never unplug the range by pulling on the power cord. Do not
manipulate your gas range plug. Do not bite, twist or tie the power
cord.
3. It is dangerous to modify your gas range specifications and
characteristics.
Do not install your gas range on top of the power cord.
4. Connect the range to its own outlet. Do not use an extension cord
or adaptor plug. To avoid any accident, before replacing the light
lamp, turn off the cook top burners
4

Care with food and cookware
1. To handle or remove food, please use the cooking gloves.
2. Never leave clothes or flammable materials near the burner when
the range is in use. When using frying oil or butter additional care
must be taken since these products are flammable.
3. Do not use the oven to store utensils, especially those containing
residues or large quantities of oil or fat.
4. Containers with curved bases or salient edges must not be used
since they can be easily destabilized when moved.
5. The handle of the utensil should be positioned so that it is turned
inward.
5

Anti-tilt Bracket
To prevent tipping
of the cooker.
Free-standing gas hotplates and electrical oven
Pressure test
connector
(For ULPG)
Test gas pressure
EV600DFSX
6

Before installing
Read the following information about the appliance and the guidelines
for ventilation.
Appliance Unpacking
Check the condition of the appliance after unpacking it.
Do not connect the appliance if it has been damaged in transport.
Dispose of packaging in an environmentally-friendly manner.
Guideline for ventilation
This appliance may only be set up in a sufficiently ventilated room and
according to the applicable regulations and ventilation requirements.
Ventilation must be in accordance with AS/NZS 5601 - Gas
Installations.
Be sure that there is a good air flow, keeping natural air ventilation
through a window or door by installing a range hood to extract the air. If
ventilation is not good, this might cause lack of oxygen, which is
dangerous for your health and the gas performance. If the gas range
will be working for a long period of time, a extra ventilation will be
necessary to increase the air flow.
Do not install in a bed-sitting room, a bathroom or shower room.
If there is another fuel burning appliance in the same room, a higher
level of ventilation will be required.
In addition to the above, during prolonged use, opening a window in
the same room is recommended. This will avoid the build up of
excessive moisture and condensation.
Installation
This appliance is always supplied with a set of adjustable feet and,
depending on the model, with a
splash guard.The appliance may also be used without the splash
guard.
Installing instruction
7

supports and burners.
• Remove the accessories from the oven.Proceed as follows:
• Tilt the appliance by raising one side slightly from the floor.
• With the plates in position, screw the adjustable feet into the
mounting holes on the underneath of the appliance.
• Repeat the process on the other side.You can make the final
adjustments to the feet in order to level the appliance once the gas
and electricity supply have been connected. If it is necessary to pull
the appliance, screw the adjustable feet in fully. Make the final settings
only when the other installation tasks have been completed.
In order to prevent tipping of the appliance, this stabilizing means
must be installed. Using ground screw 2 to mount the anti-title bracket
1 on the ground showed as the below picture .
Fitting the adjustable feet Before hand:
•Remove all parts that are not permanently fixed, especially the pan
8

Gas appliance installation
1> Leave at least 80 to 85cm between
the top of the gas appliance and any
cabinet or appliance hood install above
prepared to be installed built in.
2>Leave at least 5cm in the back and
2cm each side of the gas appliance to
allow the heat to get out.
3>When installing the oven, be sure
not to block the oven exhaust port.
Electrical connection
Only a licensed expert may connect the appliance.The appliance must
be installed according to the most recent IEE regulations (Institute of
Electrical Engineers).The appliance could become damaged if
incorrectly connected.Make sure the voltage of the power supply
corresponds to the specified value on the rating plate. The rating plate
can be found on the inside of the storage compartment flap.Ensure
that the power supply is properly earthed and that the fuse and the
wiring and piping system in the building can withstand the load from
the appliance. It is recommended that you configure the circuit for the
appliance to 16 A. When you route the mains cable, make sure that:
• the cable is not trapped or squashed.
• the cable does not come into contact with sharp edges or cutting
edges.
• the cable does not come into contact with parts that can reach
temperatures of more than 50 °C above room temperature.
Connecting the mains cable
Where the appliance is directly connected to the power supply, an
all-pole isolating switch with a contact gap is required.Complete
disconnection in compliance with the conditions specified in
overvoltage category III must be guaranteed.The earth cable is
excluded from this.
80 to 85cm
5cm
4>After installation,please paste the rating
label on visible location or nearby.
9

The appliance must be connected in accordance with the currently
applicable regulations. Before installing the appliance, check that the
local conditions (type of gas and pressure) are compatible with the
appliance settings. The permissible appliance settings can be found
on the rating plate.Connection to the gas lines and seal fitting must be
carried out professionally according to the currently applicable
standards.
Gas connection on the appliance
The gas connection is located at the rear left of the appliance.
Connecting pieces
NG corrugated tube union(and seal)
Gas connection
An inlet manifold extension pipe must be fitted to the appliance.
Ensure that the pipe is connected using the washer provided and
that the bracket is screwed to the appliance as shown in the
diagram below.
Fit the supplied pressure regulator (for Natural gas) using the NG
test point adaptor and washer to the inlet manifold. Ensure the
arrow is pointing towards the appliance and that pressure testpoint
is accessible from the final position.
Push the cooker back and install the anti-tilt bracket.
Connect the appliance to the consumer piping outlet using only
fixed piping.
This final connection is made when the product is pushed back into
position by access under the cooker.
10

4 burner models: set the burner pressure to 2.75kPa for ULPG, set
the burner pressure to 1kPa for Natural Gas. For commissioning of
the appliance with the regulator for Natural Gas, the test point
pressure should be 1.00kPa with all burners operating on HIGH.
Apply a manometer to the test nipple and reset the regulator if
necessary. Do not forget to replace the test nipple screw and to leave
the instruction book with the user.
Test point for ULPG gas
WARNING:
This appliance has to be installed as per AS/NZS 5601 and if a hose
connectino is made, hose assembly must:
1) Be certified as conforming with AS/NZS 1869, and be Class B or
Class D.
2) Diameter 10mm (minimun).
3) Length 1000mm (maximum).
WARNING:
Ensure hose assembly is restrained from accidental contact with
the flue outlet of an under bench oven.
The hose assembly should be kept clear of the floor when the
appliance is in the installed position.
Test point for Natural gas
11

Safety valve
The installation of a safety valve for opening and closing the gas
supply is a compulsory requirement. Fit the safety valve between the
gas connecting line to the appropriate room and the hob. Ensure
unhindered access to this valve.
Checking for leaks
After connecting the gas line, check the connections for leaks using
soapy water.
Initial use
Switch the appliance on as described in the instruction manual. Light
all the burners and check that the flames remain stable at both the
high and low settings.
Converting the gas type
If the appliance is not already set up for the existing type of gas, the
appliance must be converted. The conversion to a different type of
gas must be carried out by an authorised expert in accordance with
the applicable regulations.
In order to convert to a different type of gas, the nozzles must be
replaced and the low flame and primary air may have to be adjusted.
12

Replacing the nozzles (Hotplate burners)
1. Remove the burner caps （A）and burner（B）from the burners（C）.
2. Remove the nozzle (D) and replace it with an appropriate nozzle for the new type
of gas.
3. Replace the gas label with the new gas label that was supplied with the nozzle set.
4. Place each burner cup(B) on the burner(C).
Setting the minimum flow
1. Switch on the gas burner.
2. Turn the control knob for the gas burner towards the small flame setting
3. Remove the control knob for the gas burner.
4. Adjust the internal setting screw until as table flame is burning correctly. Loosen
the adjuster screw to increase the gas flow or tighten it to decrease the gas flow.
Check that the flame does not go out when the gas flow is quickly changed between
maximum and minimum, and vice versa. The setting is correct when the height of the
small flame is approx. 3 to 4mm.
13

Positioning and leveling
Positioning the appliance
When installing the appliance, make sure that there is enough space
in the final installation location to pull the appliance forwards for
cleaning and maintenance work. The ground underneath must be
hard and stable. The wall immediately behind the appliance must be
made from non-flammable material, e.g. tiles. If you need to pull the
appliance in order to position it, make sure that the adjustable feet are
screwed in fully.
Levelling the appliance
Level the appliance once all other work has been completed. To do
this, turn the adjustable feet.
14

Using instruction
Your new appliance
Get to know your appliance. You will find information about the control
panel and hob, as well as the oven, types of heating and accessories.
1
2
3
4
5
6
7
8
9
1. Pot rack
2. Burners knobs
3. Timer knob
4. Function knob
5. Temperature knob
6. Baking rack
7. Oven door
8. Door handle
9. Base
15

The control panel
The hob
Control knobs for gas burners
Adjust the heat setting of the gas burners using the control knobs. The
symbol above the control knob shows you to which gas burner the
control knob belongs.
Rapid Burner Auxiliary burner
Semi-Rapid Burner
Pan support
Steam outlet
A
C
B
D
Control knobs
Gas burners
Timer
Control knobs
Oven function
Control knobs
Oven temperature
16

Operating gas burners
Make sure that the burner lid always sits exactly on top of the burner
cup. The slots on the burner cup must be open. All parts must be dry.
Switching on the gas burner
1. Press the control knob for the required burner and turn it to position
. The gas burner ignites. Keep the control knob pressed for a
few seconds until the flame stabilises. And push the ignition button
at the same time（for some models are auto-ignition).
2. Adjust the burner to the desired flame setting.
lowest flame setting
highest flame setting
Steam outlet
Risk of burns.
Hot air from the oven escapes out of the steam outlet on the hob.
Never touch the steam outlet. Please note that, in the case of
appliances with a hob cover, the burners in the oven may also only be
switched on if the hob cover is open.
Function button for ignition
Ignition can be manual or auto.
Control knob for oven
Use this control knob to the function
Off
*Shut down where incorrect procedures can result in a hazardous
condition.
17

Symbol Power Function
25 The lamp work
58 The lamp and circulation motor work
2600 The top heating element ,grill heating element,
circulation motor ,lamp and rotary motor work
2580 The top heating element ,grill heating element,
circulation motor ,lamp work
1629 The grill heating element, lamp and rotary motor
work
2108 The top heating element, bottom heating
element ,lamp and circulation motor work
2075 The top heating element, bottom heating element
and lamp work
1125 The bottom heating element and lamp work
2058 The turbo heating element, lamp and circulation
motor work
And then, use this control knob to the temperature
Baking
OFF
Oven electric on,the minimum temperature
Oven electric on, temperature
Oven electric on，the maximum temperature
50 – 200
Broil
There is a limit stop between settings 250 and 0.
Do not turn the knob beyond this point.
Operate your oven
Please note that, in the case of appliances with a hob cover, the
burners in the oven may only be switched on if the hob cover is open.
18

Switching on the oven lighting
Press down the function button for the oven lighting until it locks into
place.The oven lighting switches on.
Switching off the oven lighting
Press down the function button for the oven lighting until it
releases.The oven lighting switches off.
Oven Control
The oven temperature setting knob can only be rotated clockwise
from the OFF position. Turn oven function control knob to select the
cooking function, meanwhile turn the timer (for the model with timer)
to set the cooking time you want. Then turn oven temperature control
clockwise to the required oven temperature. The red oven
temperature pilot light will immediately illuminate and will
automatically go off when oven temperature reaches the temperature
setting.
The minute minder is a countdown timer which emits an audible signal
when the cooking time has elapsed. The minute minder runs
independently of the oven.
Control knob for minute minder
Off
20 - 120 Cooking time in minutes
Setting a cooking time
Turn the control knob once round clockwise, as far as the limit stop,
and then turn it anti-clockwise to set it to the required time.
The cooking time has elapsed
A signal sounds once the time has elapsed.
The minute minder
19