EuroLite DS-10 User manual

OPERA TING INSTßlJCTIONS
CAUTION! 1
Keep this device away from rain and moisture!
Unplug mains lead before openlng the housing!
For your own safety, please read this user manual carefuliy before you initial start-up.
Every person involved with the installation, Operation and maintenance of this device have to:
- be qualilfied
- foilow the instructions of this manuai
@XYIHZ# Caution! Be careful with your operations.
With a voltage of 230V you tan suffer 8 dangerous electric shock
when touching the wires!
INTRODUCTION
Thank you for having Chosen a EUROLITE DS-10. The DS-10 features a built-in micro.
Unpack your DS-10.
Before you initial start-up, please make sure that there is no darnage caused by transportation. Should there
be any, consult your deaier and do not use the device.
SAFETY INSTRUCTIONS
This device has left our premises in absolutely perfett condition. in Order to maintain this condition and to
ensure a safe Operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or Problems.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might darnage your device. Leave the device switched off
until it has reached room temperature.
During the initial start-up some smoke or smeii may arise. This is a normal process and does not necessarily
mean that the device is defective.
Please consider that damages caused by manuai modifications to the device are not subject to warranty.
OPERATING DETERMINATIONS
This device was designed for indoor use only.
DOnot Shake the device. Avoid brute forte when installing or operating the device.
4

You tan install the device at any desired place. Please make sure that the device is not exposed to extreme
heat, moisture or dust. There shouid not be any cables iying around. You endanger your own and the safety
of others!
Please consider that for safety reasons unauthorized modifications to the device are forbidden!
INSTALLATIONOFTHELAMPS
m
DAWGERI
instaii the iamp with the device switched off only.
Unplug from mains before!
To install the lamps (POLE BURNER R-7-S 23OV/lOOW) open the Service iid. During the installation do not
tauch the glass-bulbs bare-handed! Please follow the iamp manufacturer’s notes!
DOnot install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device
was not designed for. Damages caused by non-observance are not subject to warranty.
Ciose the lid and make Sure that the venting Slots are not blocked.
D O not operate this device with opened Service iid!
INSTALLATION
&b
DANGER OF FIRE!
4
When instaiiing the devlce, make sure there is no highly infiammabie material
(decoration articles, etc.) in between a distance of min. 0.5 m.
When choosing the device’s installation place, please make sure that the venting Slots are not covered by
other devices or decoration material.
Mount the projector with the mounting bracket to your trussing System. For safety reasons use an additional
safety rope.
This device falls under protection ciass i. Therefore it is essential that the yellow/green conductor gets
connected to earth.The eiectric connection must be carried out by a quaiified employee.
OPERATION
After you connected the effect to the mains, the DS-10 Starts running. You tan do without a controller as the
DS-10 features a built-in microphone, which provides automatic Sound control.
CLEANING AND MAINTENANCE
in Order to obtain the best Ventilation possibie, keep the venting Slots clean from dust and dirt. We also
recommend frequent cieaning of the lenses and mirrors.
if the lamp burns out the fine-wire fuse of the DS-10 might fuse, too. Replace the fuse by a fuse of same type
and rating.
Should you need any spare Parts, please use genuine Parts oniy and give your dealer the serial numbers of
the Parts in question when orderfng.
Before repiacing the iamp, unpiug mains iead and let the iamp cool down.
When operating halogen lamps, the lamp will resch temperatures of up to 200°C.
CAUTION :
5

DOnot tauch the device’s housing bare-handed during its Operation!
DOnot flash the DS-10. Flashing the lighting effect will reduce the lamp’s life because the resulting heat
cannot be reduced by the ventilating fan.
in general, lighting effects are not designed for permanent Operation. Consistent Operation breaks will ensure
that the device will serve you for a long time without defects.
in generai, lighting effects should not be connected to dimmer Packs.
CAUTION! EYEDAMAGE!
Avoid iooking directly into the light Source (meant especialiy for epiieptics)!
Should you have further questions, please contact your dealer.
TECHNICAL SPECIFICATIONS DS-IO:
I Power SUDD~V: !230V/50Hz
1
I Power consumr>tion:
I15ow
I
Dimensions (LxWxH):
280 x 180 x 210mm
Weiqht:
1.6kg
Fittingiamps: POLE BURNER R-7-S 23OVAOOW
Pieasenote:Allspecificationsare subject to Change withour Prior notice.
2l97 0
Errors and omissions excepted.