EuroLite ColorSpot Par 64 User manual

1 of 4 pages
ColorSpot Par 64
Operation
Manual
The ColorSpot Par 64 15 5W LED is a IP65 rated exterior LED fixture featuring four-in-one
RGBW LED diodes. With a total power consumption of 95 Watts the ColorSpot 64 is an energy
efficient fixture capable of providing a smooth color wash effects. Set up and control is done via a
wireless remote IR receiver which is on the face of the unit. Once set up, the unit can be operated from
DMX with 4 different DMX control modes, and features built in macro programs all of which can be
accessed via DMX or the optional wireless remote IR controller. You can daisy chain power up to 7
fixtures with 2, 5, & 10 meter cables. Designed and built with a rugged aluminum die cast housing and
internal thermal protection to ensure long life and operation.
Specification:
1.Weight: 11lbs
2. Size: 9.8”×7.4”×11.8”
3. Power input:AC100V-240V/50HZ-60HZ
4. Wattage:95W
5. LEDS: 15PCS 5W (4 in one)
6. Beam angle of LEDs: 40 degree
7. 3PIN female and male XLR socket, 4 PIN female and male power socket
8. 4-button LED digital display
9. IR remote available

2 of 4 pages
10. IP rate: IP 65
It has seven kinds of operation mode, they are as
follows:
Static color select mode, Manual dimmer color mode, Color change mode, Color dreaming
mode
Auto-run mode, Slave mode, DMX
mode
Here above seven kinds running mode are selected by MODE button. Press MODE and UP button at
the same time, when it is on, you can initialize it at extra factory setting, running on the auto-
run program mode. To make the display stay on all of the time press the MODE and UP buttons
at the same time. To make the display turn off after 20 seconds, press the MODE and DOWN
buttons at the same time.
1. Static color select
mode
Press “MODE ” button, select static color select mode. four digital tube d isplays “ CL .××”,
Press “UP”or “DOWN”to select static colors 0-15 under this mode. Then press SET UP button to
choose the flash speed mode.When“FS.××”is displayed, press “UP” or “DOWN” button to adjust
the flash speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.
2. Manual dimmer color
mode
Press “MODE” button, select manual dimmer color mode. At this time, four digital tube
displays“r.×
××”.Press “SET UP” to choose the display 4 colors, red“r.×××”,green“G. ×××”,
blue“b.
× × × ” and w hite “h. × × × ” ,then press “UP” or “DOWN” button to set the dimming
rate (0-255).Then press SET UP button to choose the flash speed mode.When“FS.××”is displayed,
press “UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the
slowest,99 is the fastest.
3. Color change
mode
Press “MODE”button, select color change mode. At this time, the four digital tube
displays“JP.××”. Press UP or DOWN to select the color change speed grade 1-99 under this
mode.(From slow to quick) Then press SETUP button to choose the flash speed
mode.When“FS.××”is displayed, press “UP” or “DOWN”button to adjust the flash speed(00-
99), “0”is turn off flash,1 is the slowest,99 is the fastest.
4. Color dreaming
mode
Press “MODE”button, select color dreaming mode. At this time, the four digital tube displays
“ Fd.×

3 of 4 pages
×”.Press UP or DOWN to select the color dreaming speed grade 1-99 under this mode.(From
slow to quick).Then press SETUP button to choose the flash speed mode.When“ FS.××”is
displayed, press “UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off
flash,1 is the slowest,99 is the fastest.
5. Auto-run
mode
Press “MODE” button, “AUTO.”is displayed, the color change program and color dreaming
program run alternatively. Then press SETUP button to choose the flash speed
mode.When“FS. × × ” is displayed, press “UP” or “DOWN”button to adjust the flash
speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.
6. Slave
mode
Press “MODE”button, select slave mode. At this time, the four digital tube displays
“SLAu.”.Press SET UP,UP or DOWN is no use under this mode.
7. DMX
mode
Press “MODE” button, select DMX mode. At this time, the four digital tube d isplay s“d.
× × × ”,then press “UP” or “DOWN”to select the DMX address 1-512.When there is no
controller signal, the four digital tube display will be flash.
DMX MODE:7 channels
mode
CH7
C H6
CH5
CH4
CH3
CH2
CH1
MODE
DMX VALUE
FUNCTION
1
0-3
No function
Strobe
11-255 (slow
qu ick )
Dimming
0-255
(dim→
bright)
White
0-255
(dim→
bright)
Blue
0-255
(dim→
bright)
Green
0-255
(dim→
bright)
Red
0-255
(dim→
bright)
2
4-17
Re d
No
function
No
function
No
function
No
function
3
18-31
Green
4
32-45
Blue
5
46-59
White
6
60-73
R+ G
7
74-87
R+B
8
88-101
R+W
9
102-115
G+B
10
116-129
G +W
11
130-143
B+W
12
144-157
R+G+B
13
158-171
R+G+W
14
172-185
R+B+W

4 of 4 pages
15
186-199
G+B+W
16
200-213
R+G+B+W
17
214-227
Color change
Spee d
0-255
(slow→
qu ic k)
18
228-241
Color dreaming
19
242-255
Auto run
Note:R---red G---green B---blue W---white
11. Operation by IR remote:
You can also operate this product by IR remote, the distance available is at most
10M. Notice: IR remote is ready to control the unit which is any
working mode. The picture of the IR remote:
AUTO RUN mode
Press “AUTO RUN” to choose Auto run mode. Press FLASH to turn on/off the flash of the
Auto Run, and then pressing “+”and “-“buttons to adjust flash speed.
Select program Mode
1. Press PROG to go in to static color select mode , color change mode or color dreaming mode
2. Press “+”or “-”or button 1-9 to choose static color when it go into the color select mode.
3.Press FLASH to turn on/off flash and press “+” or “-”to adjust the flash speed. Press
SPEED to set the program running speed (effective only color change mode and color dreaming
mode)and press “+” or “-”to adjust it.
M/S mode
Press SL to display SLAV mode. The R/G/B/W lights are off when without master
light .
Select light program mode
Press R/G/B/W to choose R/G/B/W colors and pressing “+”and “-”buttons to adjust the
intensity of the light. Press FLASH to turn on/off flash effect to in this situation, pressing “+”
and “-”buttons to adjust the flash speed.
DMX MODE

5 of 4 pages
Press D to display DMX mode. The R/G/B/W lights will flash 2~3 times indicates that the LED
light has been set to DMX mode.
Set ADDR
Press this button to set the DMX address or initialize the program, then the red, green ,blue and
white lights will flash 2~3 times. Please put in 3 number ,for example, 1 2 3. After the red light is on,
please put in the first number. After the first number is accessed the green light will be on, then put in
the second number. When the blue light will be on, please put in the third number. After all the three
number are put in, the red, green ,blue and white lights will flash 2~3 times, which indicate that the
DMX address is right and it go in to the DMX MODE automatically. If the address is wrong the red
light will be on. New DMX address should be put in.
If the 951 are put in, red and green lights will be on. Put “0” to initialize the program. If the wrong
address is put in, the red light will be on, indicating new address should be put in. Then the system
will run in the designed mode.
Black Out mode
Press “BLACK OUT” to set the LED lights power on or power off by pressing this button.