Euroseats 75.BUR.002 User manual

7 4 8 2
3 2 4 4
1 2 2 2
526 4
C
DST4.2x16mm 52
16
B
10
92
A
5x5
1
2
3
3
Cx16
A
5x5
10 2
1
2
A
C
6
6
1 2
E
M6X16mm 8
1
A
11 4
1
ST4.8x16mm
12 12
125KG
600-1230mm
1100-1800mm
3
38mm /s
0-40°C
CE F CC C UL
100-240V
10
2
2
3
5
6
7
8
9
11
11
12
10
4
A
C
5
2Dx44
12
D
1
A
4x4
Item No.: 75.BUR.002
Installation guide
Technical data
Max. Weight
Capacity
Column Stage
Height Range
Width Range
Duty Cycle
Input Voltage
Max Speed
Temperature
Certification
10%，Max. 2 min on/ Min. 18 min off
Accessory list
Attention: The drawings below are only for reference which might be slightly
different from the actual object, please in kind prevail. Any tools missing or
installation problems,please contact the customer service firstly.
No. Image Spec Qty
Allen Key
4x4mm
Allen Key
5x5mm
M8X35mm
Component list
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
Control Box
Left Lifting
Column Right Lifting
Column
Connecting Beam
Side Bracket
Cover
Supporting Beam
Cable Management Tray
Hand Switch
Power Plug
Adhesive Pad
Panel Fixed Base
STEP 1
Install the connecting beam(3) use
5*5 wrench(A) to tighten the screws.
Use 5*5 wrench(A)
to tighten the screws
Install the connecting
beam(3)
STEP 2
Install the supporting beam(5) use 5*5
wrench(A) to tighten the screws(C).
Install the side bracket(6), and use
5*5 wrench(A) to tighten the screws(C).
STEP 3 Install the tabletop
Loosen
Pull
Tighten
Tabletop
Attach the adhesive pad

9
D
Dx2 2
1
Bx8
A
4x4
Ex10
11
A
B
E
9
8
7
1
2
8
9
10
4
STEP 4 Install the control box (8)
and the hand switch (9)
Install the control box (8) to
the tabletop with screw (D)
Install the hand switch (9)
to the tabletop.
The control box (8) can be attached to the cable management tray (7) or the tabletop
as shown. However, if you use CB38M2A(IB) control box, it has to install to the
tabletop only. Otherwise, the anti-collision system will not work well.
Attention
STEP 5
Connect all the cables onto the control box(8).
STEP 6
Power port
Handswitch Port for cable
connected to
the lifting
column
Install the cable management tray
Slide the plate
Tighten the screw
STEP 7
Install the panel
Panel
Connect the panel to the panel
fixed base (11)
Adjust the panel fixing bases (11)
according to the thickness of
screen, and use 4*4 wrench(A)
to tighten the screws(B).
Fix the screen before
install it to prevent it
from tipping-over.
Attention
Common fault treatment
The following tips will help you detected and eliminate the common fault
and error.If the fault you met is not listed below, please contact with your
supplier. Only themanufacturer and professionals are capable for investigating
and correcting those fault and error.
Fault phenomenon Method
No response while long pressing
down arrow after connected with
a power supply
1.Check if all the cables be connected well
1.Check if all the cables be connected well
2.Contact your supplier or dealer
2.Contact your supplier or dealer
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
1.Check if overloaded, max loading: 125kg;
1.Check if overloaded, max loading: 125kg;
1.Check if overloaded, max loading: 125kg;
2.Contact your supplier or dealer
2.Contact your supplier or dealer
2.Contact your supplier or dealer
The motor not move as instructed 1. Contact your supplier or dealer
1.Reposition
2.Contact your supplier or dealer
Go down but not go up
Downward sliding
Frequently Reposition
Overwork
（Duty cycle:Max 2min on/18min OFF）
1.Restart after suspend for 18mins while
connecting with power;
2.Contact your supplier or dealer;
1. Press "M"and "3" together for 3 seconds or
more, after hearing continuous beeping for twice,
it will restore factory settings
Not enough up&down height
2.Contact your supplier or dealer
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.