Whalen Amesville MNFP50AV26IA User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2020-05-20 Rev. 0001-A
Amesville 50” Fireplace Console
Model # MNFP50AV26IA
# MNFP50AV26IB
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PUR
C
HA
SE
D
:
/
/

2
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 3 and 4 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH A DAMP CLOTH.
Insert dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
GLUE
XX
FINAL
1 2 43
Children have died from furniture tip-over.
To reduce the risk of furniture tip-over:
 ALWAYS install tip-over restraint provided.
 FOR use with televisions weighing 70 lbs or less. Use with heavier televisions m
ay
result in instability causing tip-over resulting in death or serious injury.
 NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
 NEVER open more than one drawer at a time.
 Place heaviest items in the lowest drawers.
Use of tip-over restraints may only reduce, but not eliminate, the risk of
tip-over.
WARNING

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Top Corner Extension (Qty. 1) C- Upper Left Side Frame (Qty. 1)
D- Upper Right Side Frame (Qty. 1) E- Upper Left Partition Panel (Qty. 1) F- Upper Right Partition Panel (Qty. 1)
G- Media Shelf (Qty. 1) H- Lower Side Panel (Qty. 2) I- Lower Left Side Molding (Qty. 1)
J- Lower Right Side Molding (Qty. 1) K- Middle Crossbar (Qty. 1) L- Base (Qty. 1)
M- Long Corner Support (Qty. 1) N- Barrister Door (Qty. 1) O- Glass Door Insert (Qty. 1)
(Pre-attached)
P- Wood Door Insert (Qty. 1) Q- Speaker Grill (Qty. 1) R- Back Panel (Qty. 1)
S- Short Corner Support (Qty. 1) Fireplace Insert (Qty. 1) Remote Control with Battery (Qty. 1)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) 1/4” x 15 mm Bolt (2) 1/4” x 32 mm Bolt (3) Lock Washer
(Qty. 10+1 extra) (Qty. 34+1 extra) (Qty. 34+1 extra)
(4) Flat Washer (5) M8 x 30 mm Long Wood Dowel (6) M3.5 x 12 mm Screw
(Qty. 34+1 extra) (Qty. 38+1 extra) (Qty. 12+1 extra)
(7) M3.5 x 15 mm Flat Head Screw (8) M3.5 x 15 mm Washer Head Screw (9) M3.5 x 15 mm Pan Head Screw
(Qty. 4+1 extra) (Qty. 22+1 extra) (Qty. 8+1 extra)
(10) Magnetic Catch (11) Handle (12) Mending Plate (13) Hook
(Qty. 2) (Qty. 2) (Qty. 4) (Qty. 2)
(14) Metal Bracket (15) Connector (16) M4 x 25 mm Screw (17) M8 x 20 mm Short Wood Dowel
(Qty. 2) (Qty. 5) (Qty. 3+1 extra) (Qty. 2 +1 extra)
Hex Wrench Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 1) (Qty. 2) (Qty. 1) (Included in plastic bag)
Tools required (not included): Phillips screwdriver, stud finder, pencil, tape measure, power drill and 1/8” drill
bit.

5
Assembly Instructions
NOTE: DO NOT fully tighten all bolts until you finish assembling all parts. Once assembled, go back and
fully tighten all bolts.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Glue two Long Wood Dowels (5) into the inner holes on each Lower Side Panel (H) as shown.
3. Attach one Lower Side Panel (H) to the Lower Left Side Molding (I) with three 32 mm Bolts (2) and three
Washers (3 and 4).
4. Repeat the same procedure to attach the other Lower Side Panel (H) to the Lower Right Side Molding (J).
H
5
5
x 2
HH
I
J
234
I/
J
H

6
Assembly Instructions
5. Glue the Long Wood Dowels (5) into the inner holes on Lower Side Panels (H), Lower Side Moldings (I
and J) and Middle Crossbar (K) as shown.
6. Using the pilot holes as a guide, attach four Mending Plates (12) to the Middle Crossbar (K) with four 12
mm Screws (6).
5
5
5
5
5
5
I
H
J
H
K
6
12
6
12
K

7
Assembly Instructions
7. Align and attach the Middle Crossbar (K) to the Media Shelf (G) with two 32 mm Bolts (2) and two
Washers (3 and 4).
8. Using the wood dowels as a guide, attach the Lower Side Panels (H) and Lower Side Moldings (I and J) to
the Base (L) with six 32 mm Bolts (2) and six Washers (3 and 4).
K
G
2
3
4
2
3
4
L
I
J
H
H
L
2
3
4
I
/J/H
The cleats face inward

8
Assembly Instructions
9. Place the Media Shelf (G) onto the inserted Wood Dowels (5) on the vertical panels and fasten it in place
with six 32 mm Bolts (2) and six Washers (3 and 4).
10. Using the pilot holes as a guide, fasten the Mending Plates (12) attached on the Middle Crossbar (K) to the
Lower Side Moldings (I and J) with four 12 mm Screws (6).
L
H
H
I
J
G
I
/J/H
2
3
4
G
L
G
H
I
HJ
6
6
12
12
I
/J
K

9
Assembly Instructions
11. Glue the wood dowels into the inner holes on the Upper Side Frames (C and D) and Upper Partition
Panels (E and F) as shown.
12. Using the pilots holes as guide, fasten the Magnetic Catches (10) to the Upper Side Frames (C and D) with
two 15 mm Pan Head Screws (9) in each.
55
5
5
CD
E
F
5
5
55
CD
9
10
C/D

10
Assembly Instructions
13. Place the Top Panel (A) upside down on a protected surface and attach the Upper Partition Panels (E and
F) to the Top Panel (A) with four 32 mm Bolts (2) and four Washers (3 and 4).
14. Align and attach the Upper Side Frames (C and D) to the Top Panel (A) with four 32 mm Bolts (2) and
four Washers (3 and 4).
15. Insert the 32 mm Bolts (2) with the Washers (3 and 4) through the cleats on the Upper Partition Panels (E
and F) and screw into the upper front panels (C and D).
A
E
F
2
3
4
Plastic slides face inward
C
D
A
E
F
2
34
2
3
4
2
3
4
Catches face upward and inward