Everdure CBIE62 Manual

DESIGNED TO PERFECTION
INSTALLATION, OPERATION
& MAINTENANCE INSTRUCTIONS
FOR EVERDURE INDUCTIVE ELECTRIC COOKTOPS
Models Included:
OBES61 INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
FOR EVERDURE BUILT-IN ELECTRIC OVEN RANGE
OBES61, OBES62 & OBES63 BUILT-IN ELECTRIC OVENS
CBIE62
CBIE72

DESIGNED TO PERFECTION
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
FOR EVERDURE BUILT-IN ELECTRIC COOKTOP RANGE
CBIE62 & CBIE72 INDUCTIVE ELECTRIC COOKTOPS
CONGRATULATIONS
Welcome to the Everdure Kitchen Community and thank you for choosing one of our many
fantastic cooking appliances. We are confident that you will now be able to meet your cooking
needs. Before you use the cooktop we strongly recommend that you read though the whole user
manual which provides the description of this product and the proper use of its functions.
To avoid the ever-present risks involved with using an electrical appliance it is vital that the
appliance is installed correctly by an authorised person and that you read the safety instructions
carefully to avoid misuse and hazards.
It is important that you retain these instructions and your proof of purchase along with any other
important documents about this product for future reference. Due to continual product
development, Everdure reserves the right to alter specifications or appearances without notice.
CONTENTS
SECTION PAGE NO.
Important Safety Instructions ………….. 3
Appliance Details ………………………… 4
Electrical Connections ………………..…. 5
Installation ………………………………… 6-7
Operating Instructions …………………… 8-10
Cleaning ………………………………….. 11
2

DESIGNED TO PERFECTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Read the assembly instruction section and safety precautions of this booklet carefully
before removing the contents of this carton.
1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by
a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. After removing the packaging, make sure to check if there is any damage to the appliance. If there is any damage, never
attempt to use the appliance and immediately contact your Authorized Service Centre. As packaging materials can be
dangerous to children, they need to be collected immediately and put out of reach.
3. In certain circumstances electrical appliances may be a danger hazard. Check the conformity of voltage and power settings,
which are specified on the information plate attached to the appliance and/or packaging, with the usage conditions available.
4. Do not place heavy objects in or on these appliances, use for storage or as a cutting surface as sharp edges can damage the
surface. This appliance is designed for cooking food only. Use flat based, stable, inductive cooking rated cooking vessels only.
5. This appliance is designed for domestic household use only and for the cooking of domestic food products. Use as a commercial
appliance will void the warranty. It should not to be used in a marine environment or outdoors and must be fully built in. Do not
use the appliances until fully installed.
6. A means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
7. The electrical connection must be accessible after installation. The appliance must be electrically isolated before any maintenance
can be performed.
8. The appliance is not intended to be operated by means of an external timer or separate remote control system.
9. Electrical connection must be made as per local wiring rules and regulations. Do not disconnect the appliance with wet hands or
bare feet, and do not disconnect the power cord with extreme force.
10. Ensure that the kitchen is well ventilated or mechanical ventilation is in use while cooking on this appliance.
11. Do not store or use flammable materials or aerosols near the cooktop. Items made from aluminium, plastic, plastic film & sugar
based foods should also be kept away from the appliance, as they may fuse to the surface.
12. WARNING – The surface temperature of this appliance exceeds 95°C. To avoid a hazard, under bench access must be restricted.
A board must be installed underneath the cooktop. Heat from the underside of the unit will be expelled by inbuilt fans – do not
block.
13. WARNING - The cooktop will become hot during and directly after use. Do not touch the surface during this time, as it may be hot
and can cause burns. To avoid burns, children should be kept away.
14. Cleaning may only be commenced on the appliance once it has cooled down and is turned off. Failure to clean properly can
damage the unit. Do not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
15. When the appliance is not being used, turn the appliance off.
16. Where this appliance is installed in a caravan, it shall NOT be used as a space heater.
17. Do not modify this appliance.
18. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the glass surface as they can scratch the surface, which may
result in the glass shattering. Clean the glass using a warm damp cloth (e.g. dishcloth) and dry it with a soft dry tea towel.
19. All cabinetry and materials used in the installation must be able to withstand a minimum temperature of 50°C above the ambient
temperature of the room it is located in, whilst in use. Certain types of vinyl or laminate kitchen furniture are particularly prone to
heat damage or discolouration at temperatures below the guidelines given above. Any damage caused by the appliance being
installed without adhering to the temperature limits set out above will be the liability of the owner. To avoid any hazards, limit
access to the under-bench section of the cooktop.
20. The appliance must be installed and put into operation by an authorised under the conditions provided by the manufacturer in this
manual. The manufacturer cannot be held responsible for any damage that might occur due to faulty installation.
21. Damage can occur to bench tops if pots and pans are allowed to overlap the bench top. This can result in heat being transferred
to the bench top. Ensure that correct sized pots & pans are used. Pans should be lifted on and off the cooktop surface and not
dragged. Cooking zones should not be switched on without cookware placed on it. Do not place empty cookware onto the
cooking zones when in use.
22. If any cracking is noticed on the cooktop, turn the appliance off immediately and call your Authorised Service Centre.
23. Do not leave the cooktop while cooking with solid or liquid oils. There may be flaming up in conditions of extreme heating. Never
pour water onto the flames occurring from oil. Immediately turn the cooktop off and cover the pan with a lid or fire blanket in
order to smother the flame.
24. Users with pacemakers should keep their upper body at least 30cm away from any operational inductive cooking zone. If in doubt,
please consult your doctor before use.
25. Do not place metal objects such as spoons or pan lids onto the cooktop as they may become hot or cause damage to the surface.
26. A small amount of noise will sometimes be heard as elements turn on & off during operation. This is normal & not a fault.
3
3

DESIGNED TO PERFECTION
APPLIANCE DETAILS
ELECTRICAL DETAILS:
COOKTOPS:
Rated Voltage: Single phase 220-240Vac 50Hz, 3-phase 380-415Vac 50Hz
7400W
COOKTOP–Directlywired to mains supply
This information can be found on the rating plate (identification plate) affixed to the underside of the
appliance.
SIZES:
Due to continual product development, Everdure reserves the right to alter
specifications or appearances without notice.
Dispose of packaging responsibly – recycle where facilities are available.
Relevant Sizes: LENGTH (mm) WIDTH (mm) HEIGHT (mm)
Cooktop Size (CBIE62) 590 520 53
Cut-out Size (CBIE62) 560 490 -
Cooktop Size (CBIE72) 780 520 53
Cut-out Size (CBIE72) 750 490 -
4

DESIGNED TO PERFECTION
ELECTRICAL CONNECTIONS
LOCAL AUTHORITY REQUIREMENTS
Installation is only permitted by a licensed electrician, and carried out according to instructions
provided by the manufacturer. Incorrect installation might cause harm and damage, for which the
manufacturer accepts no responsibility.
ELECTRICAL INSTALLATION
Before carrying out the connection to the power supply, the voltage rating of the appliance (stamped on the
appliance identification plate) must be checked for correspondence to the available mains supply voltage, and
the mains electric wiring should be capable of handling the oven’s power rating (also indicated on the
identification plate). If you have any doubts, call in a qualified technician.
NOTE: For connections to the mains power supply, never use adapters, reductions or multiple power points as
these may overheat and catch fire. Do not install separate timers.
After having installed the appliance, the switched outlet must always be in an accessible position.
The electrical safety of this appliance can only be guaranteed if the cooktop is correctly and efficiently earthed,
always ensure that the earthing is efficient; if you have any doubts call in a licensed electrician to check the
system. The manufacturer declines all responsibility for damage resulting from an installation which has not
been correctly earthed.
WARNING: If any damage occurs to the power cable during or after installation, it must be replaced
immediately by a licensed electrician with a replacement cable from your Service Centre.
The cooktops are to be connected to a single phase 220-240Vac 50 Hz supply (leaving the connections
between points 1-3 in place) or 3 phase 380-415Vac 50Hz supply (removing the connections between points
1-3). They are earthed via the cable.
The mains terminal block is located on the underside of the cooktop and the terminals are accessible by
removing the terminal block cover by removing the cover screw. Connect the appliance as shown in the
diagram to the right.
The appliance is designed for fixed connection to the mains. During installation, an all pole disconnector
should be included inside the supply circuit with a contact opening of at least 3mm (rated 32A, delay
functioning type). The power supply cord must not touch against any hot surfaces and must be placed so that
its temperature does not exceed 75 °C at any point along its length.
IMPORTANT: The appliance must NOT be connected to the mains supply by means of a 10A or 15A plug and
socket.
5

DESIGNED TO PERFECTION
INSTALLATION
The adjacent furniture must be able to withstand a minimum temperature rise of 50°C above the
ambient temperature of the room it is located in, during periods of use. The power supply to the
appliance must be cut off before any adjustments or maintenance work is done on it.
PREPARATION FOR INSTALLATION AND USE
Manufactured with best quality parts and materials, this modern, functional and practical cooktop will meet
your needs in all respects. Make sure to read the manual to obtain successful results so as not to experience
any problems in the future. The information given below contains rules that are necessary for correct
positioning and service operations. They should be read without fail, especially by the technician who will
position the appliance.
CHOOSING A LOCATION FOR THE APPLIANCE
There are several points to pay attention to when choosing a location for your cooktop. Make sure to take
into account our recommendations below in order to prevent any problems and dangerous situations, which
might occur later!
When choosing a location for the cooktop, attention should be paid that there are no flammable or
combustible materials in the close vicinity, such as curtains, oil, cloth etc. which quickly catch fire.
Furniture surrounding the cooktop must be made of materials resistant to temperatures above 50 C°.
Required changes to wall cabinets and exhaust fans above a built-in cooktop as well as minimum heights
from the oven board are shown in Figure 1. Accordingly, the exhaust fan should be at a minimum height of
65 cm from the cooktop. If there is no exhaust fan the height should not be less than 70 cm.
6

DESIGNED TO PERFECTION
INSTALLATION OF BUILT IN COOKTOP
In order to prevent leakage of any liquids on the counter, a special sealing tape is supplied together with
your oven. Apply this seal around the bottom edge of the cooktop (see below). The brackets are installed to
hold the cooktop in place.
Cut out a hole in the bench top as shown below. Place the cooktop (controls to the front) in the hole and fix in
position using the brackets.
The bottom of the cooktop reaches temperatures above 95°C. A board must be placed a minimum of
130mm below the cooktop that prevents anyone from touching the underside of the cooktop. Take care that
there is adequate ventilation for air exchange to the inductive elements.
7

DESIGNED TO PERFECTION
OPERATING INSTRUCTIONS
The basic layout of the induction cooktop is shown in the diagram below.
The induction cooktop appliance is operated by touching buttons, with the functions confirmed by LED displays
and acoustic signals.
Turning On and Turning Off the Cooktop Appliance
NOTE: Do not operate the cooktop without first placing a suitably sized cooking vessel containing food on the
appropriate cooking zone. Missing or incorrectly sized cookware will cause the “U” fault to be displayed on the
Heat level display (cooking zone off). Turn off the cooking zone or replace cookware to continue cooking.
If the appliance is in
Stand-By-Mode, it is put into Operating-Mode by pressing the On/Off button for at least 1
second. A beep signal indicates the successful operation acoustically.
On all Heat Level Displays a ´0` will appear and all
Decimal Points of the Heat Level displays will flash (1
second on, 1 second off).
If there is no operation within 20 seconds, all the Heat Level Displays will automatically turn off. If the displays
are turned off, the hotplates will be re-set into
Stand-By-Mode .
If
On/Off is pressed for more than 2 seconds (in Operating-Mode ), the appliance is switched off and is set into
the
Stand-By-Mode again. The appliance can be turned off by pressing On/Off at any time; even if other
buttons are pressed simultaneously.
If there is a residual heat of a hotplate remaining, this will be indicated in the correspondent heat setting Heat
Level
Display as a red “H” .
Selecting A Cooking Zone
Select a single cooking zone by pressing the corresponding Heater Selection Button , and the Decimal Point of
the chosen cooking zone turns on. For the selected cooking zone, you can set or adjust the heat level between
1-9 by touching the
Increase Heat Setting Button or Decrease Heat Setting Button . All of the other cooking zone
displays will have a visible ‘O’ or ‘H’ (if recently used) but they will not have a decimal point.
If left idle for more than 10 seconds, the decimal point on the chosen cooking zone display will turn off (the
cooking zone is no longer selected). Press the
Heater Selection Button again to select the cooking zone again.
Other cooking zones can be selected without waiting for the previous one to become inactive.
The Heat Level Display works on a thermostat system. This means that the cooking zone will switch on and off
in order to remain at the chosen Heat Level. NOTE the cooking zone will remain on for longer periods if a
higher Heat Level is chosen, alternatively the cooking zone will be on less regularly on lower Heat Level
Settings.
8

DESIGNED TO PERFECTION
Turning Off Individual Cooking Zones
A particular cooking zone can be turned off in 2 different ways:
A) Selecting the cooking zone & then simultaneously pressing the
Increase Heat Setting Button and Decrease
Heat Setting Button
, after which a beep signal sounds and “0“ appears in the Heat Level Display.
B) Reduction of the heat setting to “0“ by operating the
Decrease Heat Setting Button . When this happens, the
associated
Decimal Point of the cooking zone will also be turned off. If there is residual heat from this hotplate
remaining, a red ´H` will be shown in the Heat Level Display area.
The Boost Function
The Boost function is available at each cooking zone. It is used to speed up the initial heat up time (say boil a
pot of water). Select a cooking zone and set the temperature. While the decimal point on the display is lit, press
the
Boost button. The display will alternate between “P” and the heat setting.
Note: The
Boost function is not always available (depending on what else is being used), and if the power
requirements are exceeded, the display will flash with an alternative setting for 3 seconds. Do not leave the
appliance unattended while this function is active.
To disable the
Boost function, press the Heater Selection Button for the cooking zone again (so the Decimal
Point
is lit) and adjust the temperature setting with Increase Heat Setting Button or Decrease Heat Setting Button .
The display will no longer alternate between “P” and the heat setting.
Locking The Keys
The child lock is used to set the appliance up so when it is first turned on, it is in a locked mode (which must be
unlocked before a cooking function can take place). While locked, touch modifications (e.g. increase heat
settings) and others will not be possible. It is only possible to switch the appliance off.
Turn the appliance on, but do not activate any functions. Press the
Increase Heat Setting Button and Decrease
Heat Setting Button
together, and then the Increase Heat Setting Button again. The display shows an “L” on all
cooking zone displays (or alternating ”H” & “L”) and will remain locked even if the unit is turned off & on.
To unlock the unit, press the
Increase Heat Setting Button and Decrease Heat Setting Button together, and then
the
Decrease Heat Setting Button again. The “L” displays will switch back to the heat settings and will not be
active when the unit is next turned on.
The
Key Lock button can be used to stop access to any functions (except the On/Off function) while the cooktop
is being used. Once the cooktop has been set up to cook, press the
Key Lock button for 2 seconds until there is
an audible alarm and the key lock symbol will be lit. Repeat the process to remove the key lock (the key lock
symbol will no longer be lit). If the unit is turned off & on, the key lock will remain active.
The Smart Pause Function
This function reduces the power of all cooking zones for 30 minutes (at which point the appliance will turn off).
Activate by pushing the
Smart Pause Button. The displays will alternate between “ " “ and their correct reading.
Turn the function off by pressing the button a second time.
9
9
9

DESIGNED TO PERFECTION
TOUCH CONTROL SAFETY FUNCTIONS
The following safety functions are available to avoid unintended operations of the cooktop control:
Hotplate Safety Cut Off
To prevent the appliance from unwanted, random button operation, a sensor monitoring is included.
In the case of one or more buttons being pressed longer than 12 seconds, the sensor monitoring routine
indicates acoustically that an “error” (pot or other object placed on the button, sensor failure, etc.) has occurred
and switches off the appliance.
If residual heat is present, it will be displayed in all other Heat Level Displays with a red “H”.
Over Temperature Switch Off
Because the controls are very close to the hotplates on the front of the cooktop, it is possible that a pot can be
placed half on the control and not sensed by the sensor safety cut off (not covering a sensor). This can cause
the cooktop to heat up to a very high temperature, which makes the glass and the buttons untouchable without
burning a finger.
To prevent the cooktop control unit from damage caused by overheating, a temperature sensor is available on
the touch control unit which will turn the appliance off when overheating occurs.
Spill Function
The cooktop has a sensor that detects if liquids are spilled on the control panel. This shows up as a flashing “F”
in each Heat level display (even when the unit is not operating). The easiest remedy is to clean/dry the control
panel with a moistened cloth and leave for a minute to dry. If the display is not repeated it is safe to continue
cooking.
Operating Time Limitation
The cooktop control has a limitation on the operating time. If the heat setting for a hotplate has not been
changed for a certain time, then the hotplate will turn off automatically (a “0“ is displayed for 10 seconds, then
the residual heat sign “H” is displayed). The limit of the operating time depends on the selected heat setting.
Heat settings 1-2: 6 hours.
Heat settings 3-4: 5 hours.
Heat setting 5: 4 hours.
Heat settings 6-9: 1.5 hours.
After an automatic turn off of a hotplate (as described above) the hotplate is operable again and the maximum
operating time for this heat setting is re-applied.
Residual Heat Functions
After all cooking processes there is some heat stored in the vitroceramic glass called residual heat. The control
can calculate roughly how hot the glass is in the worst case. If the calculated temperature is higher than + 60 °
C, then this will be indicated in the corresponding Heat Level Display after the hotplate control has turned off
with a red “H”. The residual heat display is shown as long as the calculated heater temperature is > + 60 ° C.
The display of the residual heat has the lowest priority and is overwritten by every other display value, during
safety turn offs and the display of an error code.
When the supply voltage is re-applied to the cooktop after an interruption to the supply voltage, the residual
heat display flashes if the corresponding hotplate had a residual heat of greater + 60 ° C before the power
interruption occurred. The display will flash until the maximum residual heat time has expired or the hotplate
has been selected and activated.
10

DESIGNED TO PERFECTION
CLEANING
NOTE: Cleaning and maintenance operations must only be carried out when the cooktop is
cool (all residual heat indicators are off).
The appliance should be disconnected from the power outlet or turned off at your isolation
switch before commencing any cleaning process.
Do not use plastic, plastic coated or aluminium cooking equipment on this appliance.
CLEANING THE COOKTOP
All cookware used on this appliance should be rated for induction cooking by the manufacturer. Cookware
with rough bases should not be used as they can scratch the glass ceramic surface. The base of the good
cookware should be as thick and flat as possible. Before use, make sure that cookware bases are clean and
dry.
Always place the cookware on the cooking zone before it is switched on. If possible, always place the lids on
the cookware. The base of any cookware used must not be smaller or larger than the cooking zones; they
should be the proper size as indicated below, so as not to waste energy. If incorrectly placed, the U symbol
will be displayed.
Before cleaning the cooktop, first isolate the cooktop from the power. Once done, ensure that there is no
residual heat stored in the appliance. Vitroceramic glass is very resistant to high temperature and
overheating. If there is residual heat stored in the appliance, the related residual heat indicator lamp will be
on. In order to avoid burns, let the appliance cool down.
Remove all spilt food and fat with a clean damp, warm, slightly soapy, dishcloth. Rinse cloth and wipe
cooktop again until clean, then wipe the cooktop dry with a clean tea towel or dry soft cloth.
If aluminium foil or plastic items are accidentally melted on the vitroceramic surface, they should be
immediately removed from the hot cooking area with a scraper specifically for vitroceramic glass. This will
avoid any possible damage to the surface. This also applies to sugar or food containing sugar that may be
spilled on the cooktop. Enamelled steel, aluminium & copper will leave a residue on the surface that should
be removed immediately or permanent damage may occur.
In the event of other food melted on the cooktop surface, remove the dirt when the appliance has cooled
down. Use cleaner for glass ceramic or stainless steel when cleaning the surface.
Do not use abrasive sponges to clean the vitroceramic surface. These materials may damage the surface.
Do not use chemical detergents, sprays or spot removers on the vitroceramic surface. These materials may
cause fire or the vitroceramic colour to fade. Clean with a damp, warm, slightly soapy, dishcloth.
WARNING: Using cookware that is too large can cause discolouration or damage to the cooktop surface
around the heat zones, which is NOT covered under warranty.
11
11

DESIGNED TO PERFECTION
A division of Shriro Australia Pty Ltd
104 Vanessa St Kingsgrove NSW 2208
AUSTRALIA: 1300 355 541
NEW ZEALAND: [phone]
www.everdure.com
IM Ref: CBIE6272 29/2013/07FC
FOR INDOOR USE ONLY