EverFocus EBA1840 eZ.HD Series User manual

EBA1840 eZ.HD Series
8MP, IP66 IR Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: September, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Introduction
EverFocus eZ.HD series cameras – EBA1840 deliver 8MP image quality. The
model is equipped with 8MP CMOS sensor and provides 4mm fixed lens with
ICR. Featured with True Wide Dynamic Range (T-WDR), the camera can
provide clear images even under backlight circumstances where intensity of
illumination can vary excessively. The EBA1840 supports both NTSC and PAL
scanning systems (auto detection) and is IP66 certified.
1.1 Packing List

Camera x 1
Mounting Sticker x 1

L-Type Wrench x 1

Screw & Screw Anchor x 4
User Manual x 1
1.2 Features
Equipped with 8MP CMOS sensor
4mm fixed lens with ICR to capture the desired field of view
Extended IR range of up to 20m / 66ft. with 18 LEDs (depends on scene
IR reflectivity)
T-WDR to improve the visibility under high contrast scene
The flexible angle viewing with its 3-Axis rotation design allows wall or
ceiling mounting
IP66-rated with metal housing
Supports UTC function: Control camera OSD settings from DVR end
1.3 Dimensions
76mm / 3"
94.5mm / 3.72"

2
1.4 Optional Accessory
BA-E310
Color / Material: White / Metal
Size (Φx H): 101 x 52mm / 3.98” x 2”
Weight: 540g / 1.2lb
BA-E173
Color / Material: White / Metal
Size (W x D x H): 173 x 111 x 114mm / 6.81”x 4.37”x 4.49”
Weight: 700g / 1.5lb
1.5 Cable Description
12VDC Power Cable
Video Output Cable (BNC, 75Ohm)
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw
positions. Drill four holes on the surface and insert the supplied 4 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 4 screw area.
2. Unscrew the Outer Housing by twisting it counterclockwise and then
remove it from the Camera Base.
Outer Housing
Camera Base
Camera Body

3
3. Screw the Camera Base to the surface with the supplied four Screws.
a. If you want to wire the cables from the Side Cut on the Camera Base:
Attach the Camera Body to the Camera Base and run the cables through
the Camera Base, and then place the cable under the Side Cut. Finally,
screw the Camera Base to the surface with the supplied 4 Screws.
Side Cut
Wall
Camera Base
Camera Body
b. If you want to wire the cables through the surface:
Attach and screw the Camera Base to the surface with the supplied 4
Screws, and then attach the Camera Body to the Camera Base.
Wall
Camera Base
Camera Body

4
4. Screw back the Outer Housing and adjust the camera angle
simultaneously.
360
°
180
°
180
°
5. Connect the Power Cable to a 12VDC power source. Connect the Video
Output Cable to a monitor or DVR.
6. You can use the Joystick on the cable to configure camera OSD settings.
Remove the Protection Cap from the Joystick before using it.
UP
DN
Configuring OSD Settings:
•Push the Joystick up / down to select
among menu items.
•Push the Joystick left / right to adjust the
level of the selected item.
•Press the Joystick to enter the submenu or
exit the OSD Setup Menu.

5
3. Configuration in the OSD Menu
No
Main
Sub Menu
Sub Menu / Function
1 Edge Det On
Level
0-10
Color
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
Off
2 Exposure
Brightness
0-20
Shutter
Auto
Mode
Normal / Deblur
Manual Speed
1/30, 1/60, 1/120, 1/250,
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/15000,
1/30000
Flicker
Sens-Up
Not supported
AGC
0-10
3 Backlight
HLC
Level
0-20
Color
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
BLC
H-POS
0-38
V-POS
0-35
H-SIZE
0-38
V-SIZE
0-35
WDR
WDR Mode
Line
ROI Mode
Box
Window Zone
0-3
Window Use
On, Off
H-POS
0-3856
V-POS
0-2176
H-SIZE
0-3856
V-SIZE
0-2176
Polygon
Window Zone
0-3
Window Use
On, Off
POS0-X
0-935
POS0-Y
0-360
POS1-X
0-935
POS1-Y
0-360
POS2-X
0-935
POS2-Y
0-360
POS3-X
0-935
POS3-Y
0-360
Off
Weight
High, Middle, Low
Off
4 Day/Night Mode
Auto
IR LED
Adaptive, Off
Anti-Sat.
0-20
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
Color
B/W
IR LED
Adaptive, Off

6
Anti-Sat.
0-20
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
Extern
IR LED
Adaptive, Off
Anti-Sat.
0-20
Extern SW
High, Low
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
5 Color AWB
Auto
Autoext
Preset
Manual
C-Temp
3000K, 5000K, 8000K
R-Gain
0-20
B-Gain
0-20
Color Gain
0-20
6
DNR
High, Middle, Low, Off
7 Image
Sharpness
0-10
Gamma
0.45, 0.55, 0.65, 0.75
Mirror
On, Off
Flip
On, Off
D-Zoom
Not supported
ACE
High, Middle, Low, Off
Defog On
Mode
Auto, Manual
Level
High, Middle, Low
Off
Shading
On
Weight
0%-100%
Off
Privacy
Box On
Zone Num
0-15
Zone Disp
On, Off
H-POS
0-120
V-POS
0-68
H-Size
0-120
V-Size
0-68
Y Level
0-120
CB Level
0-68
CR Level
0-120
Trans
0-68
Off
Polygon On
Zone Num
0-7
Zone Disp
On, Off
POS0-X
0-240
POS0-Y
0-136
POS1-X
0-240
POS1-Y
0-136
POS2-X
0-240
POS2-Y
0-136
POS3-X
0-240
POS3-Y
0-136
Y Level
0-20

7
CB Level
0-20
CR Level
0-20
Trans
0-3
Off
8 Motion On
Det Window
Window Use
0-3
Window Zone
On, Off
Det H-POS
0-96
Det V-POS
0-56
Det H-Size
0-96
Det V-Size
0-56
Sensitivity
0-10
Motion OSD
On, Off
Text Alarm
On, Off
Signal Out
On, Off
Off
9 System
Output
Frame Rate
4K/15fps, 4MP/30fps, 1080p/30fps
Freq
60Hz (auto detection)
Analog Mode
AHD, TVI, CVI, CVBS
Confirm
Yes
Return
Exit
Image Range
Full
Comp
User
Offset
0-32
Color Space
HD-CbCr, SD-CbCr, YUV
Audio Mic
Not supported
Color Bar
On, Off
Language
ENG, CHN, CHN(S), JPN, KOR, POR, ESP
Cam Title
Left-Down
Right-Up
Off
Reset
On
10
Exit