Evo EVO2-DIRVF600WDR-2,8~12 User manual

&70%*37'8%3_ (S82021)
600TVL DN WDR (2.8~12) Internal IR Dome
V1.0120308-1

Dear Customers!
INFORMATION
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for your
confidence and kindly ask you to read the following instructions carefully before
Installation and operation in order to take full advantage of all quality features regarding
this product.
CAUTION
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
The lighting flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to
all local codes.
2 3
Table of contents
1. Precautions ------------------------------------------------------------- 4
2. Limitation of liability --------------------------------------------------- 5
3. Disclaimer of warranty ----------------------------------------------- 5
4. Package ----------------------------------------------------------------- 6
5. Special Features of the model ------------------------------------- 7
7. Installation --------------------------------------------------------- 9~13
7-1. Opening the dome ass’y
7-2. Vari focal Lens adjustment
7-3. Tool-free 3-Axis mounting mechanism
7-4. Installation overview
6. Name and function of each part ------------------------------------ 8
8. Functions and operation -------------------------------------- 14~25
8-1. On Screen Display (OSD)Menu Configuration
8-2. Setting up the menu
8-3. LENS
8-4. EXPOSURE
8-5. DAY / NIGHT
8-6. WDR / BLC / ECLPS
8-7. White Balance (WHITE BAL,WB)
8-8. 2D-DNR (2D Noise Reduction)
8-9. 3D-DNR (3D Noise Reduction)
8-10. EFFECTS
8-11. SPECIAL MENU
8-12. EXIT
9. Troubleshooting ------------------------------------------------ 26~27
10. Dimension (mm) --------------------------------------------------- 27
11. Specification -------------------------------------------------------- 28
12. Warranty Information----------------------------------------- 29~30

Please read the manual carefully before the installation in order to set up the camera
correctly and to obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should be only carried out by an authorized personnel according to
local safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from
power supply and have it checked by your authorized dealer before reusing.
If you are not a certified person, never try to dismantle the camera. To avoid electric shock,
never remove the screws or covers. There are no parts inside that need maintenance by
the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time.
Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
CCD may go defective at this condition.
This publication is provided “AS IS” without warranty of any kind, either express or implied,
including but not limited to, the implied warranties of merchantability, fitness for any particular
purpose, or non-infringement of the third party's right. This publication could include technical
inaccuracies or typographical errors. Changes are added to the information herein,
at any time, for the improvements of this publication and/or the corresponding product(s).
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to below:
Please give a special attention to keep the unit from dangerous drop or external shock during
the process of transportation or handling.
Please give a special attention to keep the unit from dangerous drop or external shock during
the process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
Avoid installing the camera at extremely hot or cold places.
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent operation
of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.

67
ledomehtfoserutaeflaicepS.5egakcaP.4
Camera x 1 Instruction manual x 1 Extra Video output x 1
* Higher resolution of 600TVL(D)/650TVL(N)
This unit has come up with an innovative way of increasing cubic resolution to more
than 30% higher than that of conventional 600TVL cameras.
It upgrades horizontal resolution to 600TVL and vertical resolution to 540TVLso that the cubic
resolution becomes 324KTVL while conventional cameras provide only 240KTVL.
* Unbeatable WDR Performance
This unit provides a very unique and far superior image scanning capability of defining the
details of differently contrasted areas compared with any other conventional WDR cameras.
With current WDR technologies, defining images in shaded areas are typically not clear
enough with over-exposed picture quality. This camera provides a special resolution to
intelligently analyze the exposure ratio and to optimize it into an unbeatably clear image
quality.
* Super Low Light sensitivity
The system specifies itself as the best resolution in the market that overcomes the limitation
of compromising light sensitivity from conventional WDR cameras.
With its special technology, it provides remarkable low light sensitivity
of 0.1Lux /F2.0 ~ 0.0001Lux w /Sens-up 512x which is at least 3 times better than any other
conventional WDR cameras.
*2D/3D Noise Reduction
2D/3D DNR achievement is another reference in new WDR technology.
It reproduces noiseless images with 2D/3D filtering Noise Reduction Technology so that
users can save the volume of storage media and HDD capacity in DVR.
2D DNR helps preserved edged in the picture, while 3D DNR realizes clear images with no
ghost effect.
* DIS (Digital Image Stabilizer)
This technology reduces blurring associated with the motion of the subject by using pixels
outside the border of the visible frame to provide a buffer for the motion.
Increasing the exposure time without blurring the image makes the moving subject stabilized
digitally.
With an operation of a wide dynamic range camera in an environment with a fluorescent
lighting, an effect that is called “color rolling” usually happens due to the lack of the
synchronization between the camera and the neon light.
New WDR technology tracks the light changes relative to the camera and adapts its own
timing to the periodicity of fluorescent illumination to the sample light at a constant phase,
virtually elimination the color rolling effect.
* Anti-Color Rolling
101-Template
4-Drilling Hole
Tapping screws
x 2
(Ø4X8L)
Tapping screws
x 2 Tapping screws x 2
(Ø4X20L)
Screw cover x 2
(Ø4X10L)
[Option]
Tapping screws x 2
Wall Mount Bracket x 1
Plastic anchor x 2 Drilling template x 1
&70%*37'8%3_ (S82021)
600TVL DN WDR (2.8~12) Internal IR Dome

8 9
noitallatsnI.7Name and function of each part.6
7-1. Opening the dome ass'y
ྙPush the upper part of rectangular holes
of the camera set by fingers and then
the inner locking is separated.
ྙOr Insert a coin into the rectangular
holes and twist it to remove the dome
ass'y.
②After unlocking, separate the dome a'ssay from the camera set.

10 11
noitallatsnI.7noitallatsnI.7
7-4. Installation overview
(1) Ceiling mount
7-3. Tool-free 3-Axis mounting mechanism
- Perfect 3-axis
a. Panning 360°
b. Tilting 90°
c. Rotation 180°
①Open dome curvature and cover as shown in 7-1.
②Remove the IR assembly from the bracket.
④Adjust focus by using Tele-Wide & Near-Far Knob.
⑤Zoom (Tele-Wide)
8QORFNWKH]RRPOHYHUE\WXUQLQJFRXQWHUFORFNZLVH
0RYHWKHOHYHUWRDGMXVWWKH]RRP
/RFNWKHOHYHUE\WXUQLQJFORFNZLVH
⑥Focus (Near-Far)
⑦Reposition the IR assembly.
8QORFNWKHIRFXVOHYHUE\WXUQLQJFRXQWHUFORFNZLVH
0RYHWKHOHYHUWRDGMXVWWKHIRFXV
/RFNWKHOHYHUE\WXUQLQJFORFNZLVH
③8QIDVWHQ7LOW/RFNLQJ/HYHUE\WXUQLQJFRXQWHUFORFNZLVHDQGDGMXVW&DPHUD6HWWRZDQWHG
ORFDWLRQ$QGWKHQIDVWHQ7LOW/RFNLQJ/HYHUWLJKWO\E\WXUQLQJFORFNZLVH
$IWHUUHPRYLQJ,5/('NLWURWDWH&DPHUDVHWE\JUDVSLQJDQGWXUQLQJWKHVHUUDWLRQLQWKH
IURQWRIWKHFDPHUDVHWDQGUHSODFHWKH,5/('NLW
Panning axis up to 360° degre
Tilting axis up to 90° degree
Rotation axis up to 180° degree
Rotation axis up to 180° degree
3DQÛ
5RWDWLRQÛ
7LOWÛ
7LOW&DPHUD6HWE\WXUQLQJ7LOW/RFNLQJ/HYHU
RS485
POWER
VIDEO
Driling template
Ceiling tile
Camera set
Tapping Screw
4X20L (2ea)
Dome ass'y
Cable out (4EA)
7-2. Vari focal Lens adjustment

12 13
.7noitallatsnI noitallatsnI.7
(3) Wall mount bracket (optional)
RS485
POWER
VIDEO
Tapping Screw
4X20L (2ea)
Camera set
Dome ass'y
Tapping Screw
4X20L (2ea)
①Drill holes on the wall or slope after doing paste a drilling template to wanted spot.
②Fix Plastic Anchors in the holes.
③Fix the Dome Base on the wall or slope by using Tapping Screws supplied.
④After fixing the location of the Camera Set, push the Dome Ass’y
(Dome Curvature and Cover) to the Dome Base.
(2) Wall or Slope mount
RS485
POWER
VIDEO
Driling template
Plastic Anchor
Ø6X30L-2ea
Tapping Screw
4X20L (2ea)
Camera set
Dome ass'y
Cable out (4EA)

4. EXPOSURE 5. DAY / NIGHT
(1) AGC (Auto Gain Control)
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 0 to 20dB.
(※Default)
- MIDDLE: Allows automatic gain control from 0 to 30dB.
- HIGH: Allows automatic gain control from 0 to 42dB.
※The higher the gain level, the brighter the screen becomes
while the higher the noise as well.
(2) SHUTTER
A. AUTO : The shutter speed is controlled automatically.
(※Default)
B. FLK : Please select FLK mode when flickering occurs
on the screen, due to an imbalance between
illumination and frequency.
C. FIXED : The shutter speed is controlled manually.
- You can select the speed from ‘1/60’ to ‘1/90,000 sec.
(NTSC), ‘1/50’ to ‘1/90,000 sec. (PAL).
- You can select Digital Slow Shutter. (DSS) between
x2 ~ x512.
※Please use FIXED mode only when the light level of the
surveillance area is fixed all the time.
(3) SENS-UP
- Low light sensitivity is greatly improved with the use of
this function.
- Low light sensitivity level is adjustable from 2 to 512 times.
- When SEN-UP level is higher, the picture becomes
brighter while noise is increased at the same rate of
SENS-UP.
ON : Adjustable SENS-UP level between x2 ~ x512.
OFF: SENS-UP is disabled.
※ Default setting is <x8>
It is used to improve the sensitivity and clarity of picture quality
at low light.
- DAY : The image is always displayed in color.
- NIGHT : The image is always displayed in black
and white.
- AUTO1 : The image is automatically converted to
B/W from Color at 3 lux.
IR WDR LEVEL : Select Anti - IR saturation level
among OFF/LOW/MIDDLE/HIGH
IR WDR ADJUST : Adjust the value in each of selected
level - 0 ~ 6
- AUTO2 : The image is automatically converted to
B/W from Color at 3 lux.
D/N LEVEL : LOW/MIDDLE/HIGH
FILTER DLY : Select the duration time about changing
the Day/Night mode.
(1 SEC, 3 SEC,
5 SEC, 10 SEC, 15 SEC, 30 SEC, 60 SEC)
NIGHT BURST : Burst ON/OFF selectable.
INITIAL SET : Initialize all settings of AUTO2 menu.
୔Default setting
- Infrared camera: AUTO1
- Non-Infrared camera: AUTO2
☞Note
When the SHUTTER is set to MANUAL mode, SENS-UP does not operate.
When the AGC is set to OFF, SENS-UP does not operate.
(4) INITIAL SET
Initialize all settings of EXPOSURE menu.
(5) SAVE
Save the settings
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
WDR
ATW
DISABLED
ON
RET
<EXPOSURE MENU>
AGC
SHUTTER
SENS-UP
INITIAL SET
SAVE
LOW
AUTO
X8
<EXPOSURE MENU>
AGC
SHUTTER
SENS-UP
INITIAL SET
SAVE
LOW
AUTO
X8
<EXPOSURE MENU>
AGC
SHUTTER
SENS-UP
INITIAL SET
SAVE
LOW
AUTO
X8
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
WDR
ATW
DISABLED
ON
RET
<D/N AUTO1 MENU>
IR WDR LEVEL HIGH
IR WDR ADJUST
SAVE 3
<D/N AUTO2 MENU>
D/N LEVEL
FILTER DLY
NIGHT BURST
INITIAL SET
SAVE
MIDDLE
1SEC
OFF
<D/N AUTO2 MENU>
D/N LEVEL
FILTER DLY
NIGHT BURST
INITIAL SET
SAVE
MIDDLE
1SEC
OFF

6. WDR/BLC/ECLPS 7. White Balance (WHITE BAL, WB)
The image quality is greatly improved with the use of this mode
when there is a strong backlight behind the object.
- OFF : Deactivates the WDR function.
- WDR : Camera scans both of bright lit background and
shaded area distinctively under an extremely
contrasted light situation. (LOW/MIDDEL/HIGH)
- BLC : Enables a user to directly select a desired area from
a picture and to view the area more clearly.
(LOW/MIDDEL/HIGH)
-ECLIPSE:
Can mask the head lights to view car license number plate more clearly.
Can select masking color.
Adjust the ECLIPS level at the GAIN CONTROL as OFF mode.
<MAIN MENU>
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
WDR
ATW
DISABLED
ON
RET
<WDR MENU>
WDR LEVEL
SAVE HIGH
<BLC MENU>
BLC LEVEL
SAVE MIDDLE
<MAIN MENU>
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<ECLIPSE MENU>
AREA SETTING
ALL AREA SET
MASK COLOR
ECLPS LEVEL 1
GAIN CONTORL
SAVE
OFF
GRAY
OFF
<MAIN MENU>
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<WB MANUAL MENU>
COLOR TEMP
RED
BLUE
INITIAL SET
SAVE
INDOOR
0
0

8. 2D-DNR (2D Noise Reduction)
9. 3D-DNR (3D Noise Reduction)
10. EFFECTS
- LOW
- MIDDLE
- HIGH
- DISABLED: Deactivates 2DNR. Noise is not reduced.
- OFF : Activates 2DNR(Level : 0). Noise is not reduced.
☞Note
<Bad pixel detection> function is operated only when <2D-DNR DISABLED> is selected.
The background noise in the low light level decreases
automatically as the level of gain changes.
- DNR LEVEL
Adjust the noise reduction level.
- DESTINATION
Adjust the 3DNR gain.
- GLOBAL MOVEMENT
Control ghost phenomenon
- %;00. : You can use a digital zoom.
ZOOM : x1 ~ x8.30
DZOOM PAN : -100 ~ 100
DZOOM TILT : -100 ~ 100
- *."(&'3&&;&: You can view still or live image.
- %&''&$5
V-FLIP : You can flip the picture vertically on the screen.
MIRROR : You can flip the picture horizontally on the screen.
ROTATE : You can flip the picture rotatively on the screen.
- $0/53"45 : 0 ~ 100
- 4)"31/&44 : 0 ~ 100
- $0-03"%+645
COLOR : ON/OFF
COLOR LEVEL : 0 ~ 200
COLOR HUE : -180 ~ 180
RED GAIN : -100 ~ 100
BLUE GAIN : -100 ~ 100
- 5"3(&5$3044 : Display ‘╇’ on the screen
COLOR : BALCK,GRAY,WHITE,RED,GREEN,YELLOW
MOVE X : -100 ~ 100
MOVE Y : -100 ~ 100
INITIAL SET
SAVE
☞ Note
When TARGET CROSS function is in operation, ‘╇’ display shall disappear if
MOTION DET function is ‘ON’
- #"%1*9&-: BAD PIXELcompensation
BP DETECTION : Make the screen completely black
by covering the camera.
SEARCH AREA : X START/Y START/WIDTH/HEIGHT
THRESHOLD : 40 ~ 1024
SAVE
(※Users may simply activate BP DETECTION and go directly to SAVE.
Then Bad pixels in full screen are compensated automatically)
- */*5*"-4&5: Initialize all settings of EFFECTS menu.
(※TARGET CROSS and BAD PIXEL modes are not initialized)
- 4"7&
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<3D-DNR MENU>
DNR LEVEL
DESTINATION
GLOBAL MOVEMENT
SAVE
24
47
OFF
<MAIN MENU>
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<EFFECTS MENU>
DZOOM MODE
IMAGE FREEZE
D-EFFECT
CONTRAST
SHARPNESS
COLOR ADJUST
TARGET CROSS
BAD PIXEL
INITIAL SET
SAVE
OFF
OFF
OFF
50
50
<COLOR ADJUST MENU>
COLOR
COLOR LEVEL
COLOR HUE
RED GAIN
BLUE GAIN
SAVE
ON
100
0
0
0
<TARGET CROSS MENU>
COLOR
MOVE X
MOVE Y
SAVE
BLACK
0
0
<BAD PIXEL DETECTION>
BP DETECTION
SEARCH AREA
THRESHOLD
SAVE 90

11. SPECIAL MENU
-$"./".&
Please position the arrow to point to ’CAM NAME’ by
using the UP or DOWN selection.
Please select ‘ON’ by using the LEFT and RIGHT selection.
Please press the button to complete ‘ON’.
☞Note
If ‘OFF’ is selected, the CAM NAME does not appear on the
monitor even if it has been input.
Up to 15 letters are offered for the CAM NAME. If you enter a
title, the title will appear on the monitor.
①Please move the cursor to the letter to choose by using the
UP and DOWN selections.
②Set an ID from A~Z /a~z /0~9 by using the UP, DOWN, LEFT
and RIGHT Selections.
③ Lock in the letters by using the button.

When the letter is locked in, the cursor moves to the next space.
④ Please repeat the above to input CAM NAME.
☞Note
When a wrong name has been input,
If you press the button after moving the cursor to CLR, all
letters will be erased.
If you want to correct a letter, please move the cursor to the
arrow at the bottom left of the screen and press the button.
①Please move the cursor onto ’POS’ and then press the button.
②The name will appear at the top left hand corner.
③Please find the position you wish to display the name by using the 4 directional
selections, and then press the Button.
-.05*0/ (Motion Detection: MD)
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen, and the
words 'MOTION' appear on the screen when movement is
detected. You can monitor activity more effi ciently.
ZONE NUMBER : You can select up to 8 MD areas.
ZONE STATE : Determines whether to use the MD area
selected in ZONE NUMBER.
WIDTH : Determines the coordinate of the horizontal size.
HEIGHT : Determines the coordinate of the vertical size.
MOVE X : Determines the coordinate of the horizontal axis.
MOVE Y : Determines the coordinate of the vertical axis.
SENSITIVITY : Determines the coordinate of the sensitivity.
INITIAL SET : Initialize all setting of MOTION DET menu.
SAVE : Select this to save the MOTION menu setting and
return to the SPECIAL menu.
-13*7"$:(Privacy Masking)
This function helps you mask an area you want to hide on the
screen.
MASK NUMBER : You can select up to 8 PRIVACY areas.
MAKS STATE : Determines whether to use the selected in
AREA SELECT.
SENSITIVITY : Determines area color. You can select GRAY,
WHITE, RED, GREEN, BLUE, YELLOW,
BLACK.
WIDTH : Determines the coordinate of the horizontal size.
HEIGHT : Determines the coordinate of the vertical size.
MOVE X : Determines the coordinate of the horizontal axis.
MOVE Y : Determines the coordinate of the vertical axis.
INITIAL SET : Initialize all setting of PRIVACY menu.
SAVE : Select this to save the PRIVACY menu setting and
return to the SPECIAL menu.
When a name has been chosen, please select a position for the name to display.
Please position the cursor on the letter you wish to correct,
and then move the cursor onto the letter you wish to choose
and press the button.
Please select ‘END’ and then press the Button to complete CAM NAME input.
<MAIN MENU>
1. LENS
2. EXPOSURE
3. DAY/NIGHT
4. WDR/BLC/ECLPS
5. WHITE BAL
6. 2D-DNR
7. 3D-DNR
8. EFFECTS
9. SPECIAL
10.EXIT
DC IRIS
AUTO1
ECLPS
ATW
DISABLED
ON
RET
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<CAMERA NAME>
----------------
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-. 123456789
CLR POS END
BACK YARD
<CAMERA NAME>
----------------
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-. 123456789
CLR POS END
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<MOTION DET MENU>
ZONE NUMBER ZONE1
ZONE STATE
WIDTH
HEIGHT
MOVE X
MOVE Y
SENSITIVITY
INITIAL SET
SAVE
OFF
20
30
15
25
50
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<PRIVACY MASK MENU>
MASK NUMBER MASK1
MASK STATE
MASK COLOUR
WIDTH
HEIGHT
MOVE X
MOVE Y
INITIAL SET
SAVE
OFF
GRAY
30
30
30
25

-
You can select the menu language according to your
requirements.
English, Korean, Russian, Spanish, French
-
This function mitigates any picture movement due to external
factors such as wind.
☞Note
The camera’s resolution decreasesbecause STABILIZER
function uses the digital zoom.
STABILIZER doesn’t operate when background illumination is
too low.
STABILIZER doesn’t operate when object pattern is monotonic
like sky or white wall.
-
CRT : GAMMA 0.45
LCD : GAMMA 1.0
-
A special area where the internal illumination is dark while strong
back light exists behind the object, normally human face
becomes unrecognizable. This mode is suited for this particular
situation.
FR BRIGHTNESS : 0 ~ 40
FR CONTRAST : 0 ~ 40
COLOR SAT : 0 ~ 200
CONTRAST : 0 ~ 100
OUTPUT LEVEL : -64 ~ 64
SHARPNESS : 0 ~ 100
-
This function sets up the camera communication status
when controlling the camera through an external control
device.
CAMERA ID : Determines the camera’s identification
number (between 0 and 255).
ID POSITION : Displays camera title on top left &
right side of the screen.
BAUD RATE : You can select
4800/9600/19200/38400/57600 bps .
SAVE/REBOOT : Select this to save the COMM SET menu
setting and return to the main screen.
PREVIOUS: Return to COMM SET menu.
-
Resets the camera setting to the factory defaults.
But <COMM SET> menu is not initialized.
☞Note
RS-485 cable : Please connect (-) firstly and then (+).
IF there happens RS-485 cable conection error or any other
problems, a message ‘ERROR RS-485 Connection.
Please Reconnect and Reboot’ is displayed.
Please reset the power or OSD.
Save all setting menus by pressing the Tact SW and then exit by pressing EXIT menu.
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<SPECIAL MENU>
CAM NAME
MOTION DET
PRIVACY MASK
LANGUAGE
STABILIZER
MONITOR TYPE
FACE REC
COMM SET
FACTORY RESET
SAVE
OFF
OFF
OFF
ENG
OFF
CRT
OFF
<COMM SETTING MENU>
PROTOCOL
CAMERA ID
BAUD RATE
SAVE/REBOOT
SAVE
PELCO D
9600
<SET CAMERA ID>
CAMERA ID
DISPLAY ID
ID POSITION
SAVE
001
OFF
12. EXIT

If there are problems in operating, please refer to the checklist below. If the problem persists,
please contact the agent where this product is purchased.
Problems Troubleshooting
Nothing appears on the
screen.
·Please check that the power cord and line connection
between the camera and monitor are fixed properly.
·Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen
is dim.
·Is lens stained with dirt? Clean your lens with soft,
clean cloth.
Set the monitor to proper condition.
485 Control Board Connection Port
(+)CONNECTION TERMINAL(TRX+)
(-)CONNECTION TERMINAL(TRX-)
RS-485 Control Port
485+
485-
Item
Initial value Camera ID 1BAUD RATE 9600 UART MODE 8-NONE-1 RET PKT ENABLE
·If the camera is exposed to too strong light, change
the camera position.
·
The image on the screen
is dark.
·Adjust the contrast feature of the monitor.
·If you have an intermediate device,
VHWWKHȍ+L=SURSHUO\
(Please check the impedance)
The camera is not working
properly, and the surface
of the camera is hot.
·Please check that you have properly connected the
camera to an appropriate power source.
7KH'$<1,*+7PHQX
does not work. ·3OHDVHFKHFNLI'$<1,*+7PHQXLVVHWWRµ$872¶
The SENS-UP function
does not work.
Color is not correct.
The MOTION DETECTION
function is not working.
Problems Troubleshooting
RS-485
communication fails. ·Please check the polarity between RS-485 Control Port and RS-485 cable.
·Please check if the initial value of the RS-485
Communication setup matches between camera and
OSD Controller or DVR.
·We recommend that you make ground connection
between camera and controller for safe communication
control.
·When RS-485 cable is not properly connected, A warning
Then please turn off the power and connect the cable again.
message µERROR RS-485 Connection. Please reconnect
and Reboot¶is displayed.
*RS-485 Communication establishment initial value
9. Troubleshooting9. Troubleshooting
·3OHDVHFKHFNWKDW$*&RI(;32685(6(783PHQXLV
VHWWRµ2))¶
·3OHDVHFKHFNWKDW6+877(5RI(;32685(6(783
PHQXLVVHWWRµ$)/.¶RUµ),;('¶
·Please check if MOTION DETECTION function is
turned on.
·Please check if MD LEVEL is too low.
·Please check the setting of the MD area.
·3OHDVHFKHFNWKHVHWWLQJRI:+,7(%$/6(783PHQX
The screen flickers
continually. ·Please check that direction of camera turns toward
the Sun.

28 29
11. Specification
MODEL (S82021) EVO2-DIRVF600WDR-2.8-12
Image sensor 1/3” Sony Super HAD CCD II
PAL : 752(H) X 582(V)
600TV Lines(Day) /650TV Lines(Night)
Synchronizing system Internal
Scanning system PAL : 625 Lines 2:1 Interlaced
Video output 1.0Vp-p Composite 75Ohms
0.1Lux at F1.2(Sens-
0.0001Lux at F1.2(Sens-up, x512)
PAL : 1/50~90,000sec.
Gamma control
WhiteBalance 1500°K ~ 11,000°K Auto.
ATW / Cor-Roll / PUSH/MANU AL
Gain control Standard : -6dB ~ 34dB Auto/ Selectable by OSD
0.005%
Power source 12VDC / 24VAC
300mAat12VD C (550mA w/IR ON)
130mA at24V
AC (250mA w/IR ON)
Lens 2.8~12mm Varifocal DC IrisLens at F1.2
N/A
LED Spectrum 850nm(Ø5) x 20EA
ViewableDistance Upto20M at Moonless Night
-10°C~ 50°C
Humidity 0%RH ~ 90%RH
Measurement(mm) 134(Ø)x91.
6(H)
Weight(Approx.g) 600
WDR
2D/3DNR
Sens-up
Digital zoom
White balance ATW/Cor_Roll/PUSH/MANUAL
Privacy mask le)
Specifications are subject to change without prior notice for better improvement.
The Recommended adaptor is DC12V/1.5A or AC24V/1A over.
WARRANTY INFORMATION
Please keep this document in a safe place. DO NOT return this document to PĂĐŝĮc CommunicaƟons.
EQUIPMENT DETAILS
MODEL SERIAL NUMBER DATE OF PURCHASE
IMPORTANT INFORMATION
PLEASE RETAIN ALL MANUALS SUPPLIED WITH THE EQUIPMENT AND PROOF OF PURCHASE.
PROOF OF PURCHASE WILL BE REQUIRED IF YOU NEED TO MAKE A WARRANTY CLAIM.
Please ensure that the following instrucƟons are followed when operĂƟng the Equipment.
x This is a commercial grade product and should only be installed or serviced by a qualiĮed
technician.
x Please read the Owner’s Manual before installing the device.
x Never place the Equipment in a conĮned space (eg bookcase, built-in cabinet) unless
proper venƟlĂƟon is available. It is advised to leave a 10cm space around the unit.
x To prevent Įre or shock hazard, do not expose the Equipment to water. Ensure that
objects Įlled with liquid (eg vases) are not placed on or near the Equipment.
x Avoid keeping or using the Equipment in a dusty, wet or electromĂŐŶĞƟc environment.
x Before making a warranty claim, ensure that you have read the “TroublesŚŽŽƟŶg” ƐĞĐƟŽŶ
of the Owner’s Manual.
PACIFIC COMMUNICATIONS
A division of Hills Holdings Limited ACN 007 573 417
Unit 10, 331 Ingles Street
City Link Estate,
PORT MELBOURNE VIC 3207, AUSTRALIA
www.pacom.com.au
12. Warranty Information

30 31
OMEM
WARRANTY TERMS
1. PaciĮc CommunicaƟons provides consumers with the following warranty in relaƟon to this Equipment, in adĚŝƟon to complying with the
requirements of any relevant legislaƟon, including the ŽŵƉĞƟƟŽŶ ĂŶdCŽŶsumer Act 2010 (Cth) in Australia and the CŽŶsumer GuarĂŶtees Act
1993 in New Zealand (the Acts), except where a New Zealand consumer acquires the relevant Product for the purposes of a business.
2. In this warranty, we have used the following deĮniƟons:
(a) PaciĮc CommunicaƟons,our or we means PaciĮc CommunicaƟons, a division of Hills Holdings Limited ABN 35 007 573 417 of 159 Port
Road Hindmarsh South Australia 5007.
(b) Equipment means the goods described in the table headed “Equipment Details” overleaf.
(c) Material means a material or component used by PaciĮc CommunicaƟons in the manufacture of the Equipment.
(d) Warranty Period means 24 months from the date of purchase of the Equipment.If the Equipment or part (as the case may be) is
repaired or replaced, there will be no extension to the original warranty period.(Note: HDD’s installed in equipment have a 12 month
warranty period)
(e) Workmanship means the handling, assembly and manufacturing processes performed by or on behalf of PaciĮc CommuŶŝĐĂƟŽŶƐ in
order to manufacture the Equipment.
3. PaciĮc CommunicaƟons warrants that for the durĂƟŽn of the Warranty Period, the Equipment will be free of faults arising from defects in
Workmanship or Materials, on the terms and condiƟons set out in this warranty.
4. PaciĮc CommunicaƟons undertakes that if during the Warranty Period, the Equipment,or any part of the Equipment, has failed to operate
correctly due to faulty Workmanship or defecƟve Material, it will repair or replace the Equipment or part (as the case may be) free of charge
on the following terms:
(a) The consumer must retain proof of purchase of the Equipment. PaciĮc CommunicaƟons may reject a warranty claim on Equipment
where the consumer is unable to substaŶƟate proof of purchase to the reasonable ƐĂƟsfacƟon of PaciĮc CommunicaƟons.
(b) The consumer must contact the service provider (installer) who installed the Equipment at Įrst instance, upon becoming aware of a
defect to any Equipment. AlternaƟvely, the consumer may contact PaciĮc CommuŶŝĐĂƟons on [phone].
(c) Following consultaƟon between the service provider and PaciĮc CommuniĐĂƟŽŶƐ PaciĮcCommunicaƟŽŶs will determine whether there
is a defect, and if so PaciĮc CommunicaƟons agrees (at PaciĮc CommunicaƟons’ opƟon) to repair, replace or supply equivalent goods, or
pay the cost of any of those remedies to the consumer.
(d) If requested by PaciĮc CommunicaƟons, the consumer must return the Equipment to PaciĮcCommunicaƟons. The consumer will be
responsible for the collecƟon and freight costs of returning the Equipment to PaciĮcCommunicĂƟons or to any designated PaciĮc
CommunicaƟons Authorised Service Centre for repair or replacement. The consumer will also be responsible for the freight costs to
deliver any new or repaired Equipment to the consumer.
(e) This warranty does not include, and PaciĮcCommunicaƟons will not be responsible for, any costs associated with the inspecƟon or
evĂůƵĂƟon of the Equipment, nor the removal or re-installaƟon of the Equipment.
(f) Please note that a service charge will apply if no fault is idenƟĮed or if any fault does not fall within the condiƟons of this warranty. For
details of the applicable service charge, please discuss this with your service provider prior to making a claim under this warranty.
5. The consumer’s right to this warranty will cease to apply where:
(a) Security labels, idenƟĮcaƟŽn numbers or serial numbers are tampered with or removed;
(b) The Equipment has not been used in accordance with the instƌƵĐƟons provided in the Owner’s Manual supplied with the Equipment,or
in accordance with usual use for that type of equipment;
(c) AlteraƟons, moĚŝĮcaƟons or repairs have been carried out on the Equipment (unless authorised by PaciĮc CommunicaƟons);
(d) Upgrades (including soŌware upgrades) are not authorised and registered by PaciĮc CommunicĂƟons.
6. This warranty is in addiƟon to any non-excludable legal rights or remedies conferred on the consumer under any applicable Act and any similar
laws. To the extent permŝƩed by law, PaciĮcCommunicaƟons’ liability for any non-excludable condiƟon or warranty is limited to recƟfying any
defect at its opƟon, as set out in paragraph 4(c).
7. Subject to the requirements of any applicable Act or legislaƟon and to the extent permiƩed by law, no liability (whether expressed or implied) of
any nature whatsoever, is accepted by PaciĮc CommunicaƟons for any consequenƟal loss, damage or injury arising as a result of any fault in the
Equipment.
8. This warranty does not extend to damage to Equipment which occurs during transit or transportaƟon, or which is caused by any abuse, accident
or improper installaƟon, connecƟon, use, adjustment or repair of goods otherwise than in accordance with instrucƟons issued by PaciĮc
CommunicaƟons.
9. The following applies to consumers who purchased a relevant Product in Australia:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are enƟtled to a replacement or refund for a
major failure and compensaƟon for any other reasonably foreseeable loss or damage. You are also ĞŶƟtled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
12. Warranty Information