Evoluent VM4SW User manual

The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. T
his equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur
in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of more of the following measures: -
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or
modifications not expressly approved by the party responsible for compliance could void yo
ur authority to
operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
1
This device may not cause harmful interference and
2 This device must accept any interference received, including interference that may cause undesired
operation.
The antenna used for this transmitter must not be collocated or operation in conjunction
with any other antenna or transmitter.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user’s authority to operate
the device.

Evoluent Vertical Mouse Install
* * *Warning * * *
Wet hand sanitizer may dama e the finish on the mouse. Wait
for the sanitizer to dry before touchin the mouse. Do not use any
chemical cleaner on the mouse.
* * *Windows Install * * *
1. Before connectin Evoluent Vertical Mouse. o to Control Panel to
remove any previous Evoluent Mouse Mana er and any other
existin mouse software, except touchpad driver, to avoid
software conflict.
2. In Control Panel, Mouse:
A.
On the Buttons tab, uncheck the box for Switch Primary and
Secondary Buttons.
B. On the Pointer Options tab, uncheck the box for Enhance Pointer
Precision and set the pointer speed slider to the middle position.
3. Connectin the Evoluent:
Connect the receiver to a USB port directly on the computer.
Insert the battery with the +side facin out. Slide the On/Off switch
to the reen position. The li hts blink when the battery Is low. The

Evoluent may not work with some external USB hubs, dockin
stations, and KVM switches.
4. Press the pointer speed button behind the wheel to li ht up 3
Indicator li hts on top of the mouse for the best pointer control.
5. Evoluent Mouse Mana er for Windows may be Installed to
confi ure the buttons to do thin s without movin the mouse or
touchin the keyboard. Download Mouse Mana er at
evoluent.com/support/download.
Durin software install, if a messa e appears about the driver not
passin Windows Testin , click Continue Anyway. This messa e
may appear multiple times. Click Continue Anyway each time.
After Install is finished, button functions may be confi ured by
double clickin the Eicon on the task bar to open Evoluent Mouse
Mana er.
* * *Mac Install * * *
1. Before connectin Evoluent Vertical Mouse, o to the Applications
folder to find and remove any existin Evoluent Mouse Mana er
and any other mouse software, except touchpad drivers, to avoid
software conflict.

2. Connectin the Evoluent:
Connect the receiver to a USB port directly on the computer.
Insert the battery with the +side facin out. Slide the On/Off switch
to the reen position. The li hts blink when the battery Is low. The
Evoluent may not work with some external USB hubs, dockin
stations, and KVM switches.
3. Press the pointer speed button behind the wheel to li ht up three
Indicator li hts for the best pointer control.
4. Evoluent Mouse Mana er for Mac may be installed to confi ure
the buttons to do thin s without movin the mouse or touchin the
keyboard. Download Mouse Mana er at
evoluent.com/support/download
After install is finished, button functions may be chan ed by
clickin the Eicon in System Preferences to open Evoluent Mouse
Mana er.
We want to make sura you are happy with your Evoluent!
If you have any questions or problems with the Vertical Mouse
please contact us at:
E-mail:[e-mail]
Phone:[phone]

Comfort Tips
1. Sit close to the desk to reduce forward arm extension.
2. Horizontal puts the wrist in a neutral posture.
(Lower desk, sit hi her, or use keyboard tray.)
3. Wrist support reduces pressure points and puts 1he wrist in a neutral
posture.
4. Compact Keyboard allows the mouse to sit closer to the keyboard and
reduce lateral arm extension.
5. Mouse and keyboard close to the ed e of the desk reduce forward arm
extension.
6. Mouse close to the keyboard reduces lateral arm extension.