Evolution EVO180 User manual

180mm (7”) TCT STEEL CIRCULAR SAW
Instruction
Manual
Read instructions before operating this tool.
www.evolutionsteel.com
®
E VO180

2www.evolutionsteel.com
EVO 180mm Steel Cutting Circular Saw
TABLE OF CONTENTS
EC - Declaration of Conformity
Important Information
12 Month Limited Warranty
General Safety Rules
Safety Instructions for All Saws…...
Symbols & Labels
Additional Specic Safety Rules….
Specication
Assembly
Machine Overview
Getting Started
Maintenance
Environmental Protection
Service Parts Diagram……………..
Original Instructions
Read instructions before operating this tool.
GB 03
03
03
04
05
06
07
07
08
09
10
13
14
15

3
www.evolutionsteel.com
E VO180
EC - DECLARATION OF CONFORMITY
We, manufacturer and importer
Evolution Power Tools Ltd.
Venture One
Shefeld
S20 3FR
Declare that the product
Part numbers:
Evolution: STEEL
Circular Saw 180mm
Complies with the essential requirements of the
following European Directives:
2006/42/EC – Machine Directive
2006/95/EC – Low Voltage Directive
2004/108/EC – EMC Directive
2002/95/EC – Restriction of the use of Certain
Hazardous Substances in Electrical and Electric
Equipment
Standards and Technical specications referred to:-
EN55014-1 : 2006
EN55014-2 : 1997+A1
EN61000-3-2 : 2006
EN61000-3-3 : 1995+A1+A2
EN60745-1 : 2003+A1
EN60745-2-5 : 2003
EN60825-1 : 1994+A1+A2
All documentation is held on le at the above
address and is available, on request for review.
Authorised Signatory
Name: Mr Matthew J Gavins
Position: Managing Director
Date: 1st June 2011
Please read these operating and safety instructions
carefully and completely. For your own safety,
before using this equipment check that the voltage
is correct and that all handles and parts are rmly
secured. If you are uncertain about any aspect of
using this equipment, please contact our Technical
Help Resource.
Technical Helpline UK 0870 609 2297
EVO 180MM STEEL CUTTING CIRCULAR SAW
Congratulations on your purchase of an Evolution
Power Tools machine. Please complete your
product registration on line to validate your
machine’s warranty period and ensure prompt
service if needed. We sincerely thank you for
selecting a product from Evolution Power Tools.
12 MONTH LIMITED WARRANTY.
Evolution power tools reserves the right to make
improvements and modications to design without
prior notice.
Evolution Power Tools will, within twelve (12) months
from the original date of purchase, repair or replace
any goods found to be defective in materials or
workmanship. This warranty is void if the tool being
returned has been used to cut materials beyond
the recommendations in the Instruction Manual or
if the saw has been damaged by accident, neglect,
or improper service. This warranty does not apply
to machines and/or components which have
been altered, changed, or modied in any way, or
subjected to use beyond recommended capacities
and specications. Electrical components are
subject to respective manufacturers’ warranties. All
goods returned defective shall be returned prepaid
freight to Evolution Power Tools. Evolution Power
Tools reserves the right to optionally repair or
replace it with the same or equivalent item. There
is no warranty – written or verbal – for saw blades.
In no event shall Evolution Power Tools be liable for
loss or damage resulting directly or indirectly from
the use of our merchandise or from any other cause.
Evolution Power Tools is not liable for any costs
incurred on such goods or consequential damages.
EC - DECLARATION OF CONFORMITY GB IMPORTANT INFORMATION GB
12 MONTH LIMITED WARRANTY GB

4www.evolutionsteel.com
No ofcer, employee or agent of Evolution Power
Tools is authorised to make oral representations
of tness or to waive any of the foregoing terms of
sale and none shall be binding on Evolution Power
Tools. Questions relating to this limited warranty
should be directed to the company’s head ofce, or
call the appropriate Helpline number.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of electric shock, this equipment
is tted with an approved cord and plug for its
intended country of use. Do not change the cord or
plug in any way.
GENERAL SAFETY RULES
Read and understand all instructions before
operating this product. Failure to follow all
instructions listed below, may result in electric
shock, re and / or serious personal injury. Save
These Instructions For Future Reference.
Read all these instructions before attempting to
operate this product and save these instructions.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
SAFETY INSTRUCTIONS FOR CIRCULAR SAWS
WARNING: Read all instructions. Failure to follow
all instructions listed below may result in electric
shock, re and/or serious injury.
Please save these instructions.
1) Work Area Safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2) Electrical Safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
3) Personal Safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
IMPORTANT SAFETY INSTRUCTIONS GB
GENERAL SAFETY RULES GB
SAFETY INSTRUCTIONS FOR CIRCULAR SAWS GB

5
www.evolutionsteel.com
E VO180
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4) Power Tool Use & Care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) Service
Have your power tool serviced by a qualied
repair person using only genuine replacement
parts. This will ensure that the safety of the power
tool is properly maintained.
6) Safety Instructions for all Saws
a) DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxiliary
handle, or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
c) Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands
or across your leg. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimize body exposure, blade binding,
or loss of control.
e) Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and shock the
operator.
f) When ripping always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
g) Always use blades with correct size and shape
(diamond versus round) of arbor holes. Blades
that do not match the mounting hardware of the
saw will run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade
washers or bolt. The blade washers and bolt
were specially designed for your saw, for optimum
performance and safety of operation.
FURTHER SAFETY INSTRUCTIONS
Causes and operator prevention of kickback:
Kickback is a sudden reaction to a pinched, bound
or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator:
1. When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator;
2. If the blade becomes twisted or misaligned in
the cut, the teeth at the back edge of the blade can
dig into the top surface of the workpiece causing
the blade to climb out of the kerf and jump back
towards the operator.
Kickback is the result of saw misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a rm grip with both hands on the
saw and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback could
cause the saw to jump backwards, but kickback
ADDITIONAL SAFETY INSTRUCTIONS GB

6www.evolutionsteel.com
forces can be controlled by the operator, if proper
precautions are taken.
b) If the blades are binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material until
the blades come to a complete stop. Never
attempt to remove the saw from the work or pull
the saw backward while the blades are in motion or
kickback may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
c) When restarting a saw in the workpiece,
centre the saw blade in the kerf and check that
saw teeth are not engaged into the material. If
saw blade is binding, it may walk up or kickback
from the workpiece as the saw is restarted.
d) Support large panels to minimise the risk of
blade pinching and kickback. Large panels tend
to sag under their own weight. Supports must be
placed under the panel on both sides, near the line
of cut and near the edge of the panel.
e) Blade depth and bevel adjusting locking
levers must be tight and secure before making
a cut. If the blade adjustment shifts while cutting it
may cause binding and kickback.
f) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
a narrow kerf causing excessive friction, blade
binding and kickback.
g) Use extra caution when making a “plunge
cut” into existing walls or other blind areas. The
protruding blade may cut objects that can cause
kickback.
h) Check lower guard for proper closing before
each use. Do not operate the saw if lower guard
does not move freely and close instantly. Never
clamp or tie the lower guard into the open position.
If saw is accidentally dropped, lower guard may
be bent. Raise the lower guard with the retracting
handle and make sure it moves freely and does not
touch the blade or any other part, in all angles and
depths of cut.
i) Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
j) Lower guard may be retracted manually only
for special cuts such as “plunge cuts” and
“compound cuts.” Raise lower guard by retracting
handle and as soon as blade enters the material, the
lower guard must be released. For all other sawing,
the lower guard should operate automatically.
k) Always observe that the lower guard is
covering the blade before placing saw down
on a bench or the oor. An unprotected, coasting
blade will cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it takes
for the blade to stop after switch is released.
HEALTH ADVICE
WARNING: When drilling, sanding, sawing or
grinding, dust particles will be produced. In some
instances, depending on the materials you are
working with, this dust can be particularly harmful
to you (e.g. lead from old gloss paint).You are
advised to consider the risks associated with the
materials you are working with and to reduce the
risk of exposure.
You should:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as
dust masks that are specially designed to lter
microscopic particles.
LABELS & SYMBOLS
WARNING: Do not operate machine if warning
and / or instruction labels are missing or damaged.
Contact Evolution Power Tools for replacement
labels.
Symbol Description
V Volts
A Amperes
Hz Hertz
min Minutes
~ Alternating current
no no load speed
Double Insulated
Read Instructions
Wear eye Protection
Wear ear protection
Wear dust mask
SYMBOLS AND LABELS GB

7
www.evolutionsteel.com
E VO180
Only use genuine Evolution replacement parts.
Unauthorized parts may be dangerous!
To obtain an additional copy of your manual, please
contact Evolution Power Tools at:
UK 0870 609 2297
WEB www.evolutionpowertools.com
ADDITIONAL SPECIFIC SAFETY RULES
a) DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on the
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot come into contact
with the blade.
b) Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
c) Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d) Never hold the piece being cut in your hands
or across your legs. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimize body exposure, blade binding,
or loss of control.
e) Hold the power tool by the insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or its
own cord. Contact with a “live” wire will also make
exposed metal parts of the power tool “live” and
shock the operator.
f) When ripping always use a rip fence or straight
edge guide. This improves the accuracy of the cut
and reduces the chance of the blade binding.
g) Always use blades with correct size and shape
(diamond versus round) of arbor holes. Blades
that do not match the mounting hardware of
the saw will run eccentrically, causing loss of
control.
h) Never use damaged or incorrect blade
washers or bolt. The blade washers, anges
and bolt were specially designed for your saw, for
optimum performance and safety of operation.
Replace with genuine spare parts if damaged or
worn.
i) Do not use High Speed Steel (HSS) saw blades
k) Inspect the machine and the blade before
each use. Do not use deformed, cracked, worn
or otherwise damaged blades.
l) Never use the saw without the original guard
protection system. Do not lock the moving guard
in the open position. Ensure that the guard operates
freely without jamming.
m) Only use blades that comply with the
characteristics specied in this manual. Before
using accessories, always compare the maximum
allowed RPM of the accessory with the RPM of the
machine.
SPECIFICATION
EVO 180 Designed to cut:
Steel Plate: Max Thickness - 8mm
Steel Box Section: Max Wall Thickness - 3mm
Stainless Steel: Blade Change Required
Aluminium: Blade Change Required
Wood: Blade Change Required
Motor (230v 50/60 Hz) (Watts) 1250w
Maximum Box Cutting Capacity
90O(3mm wall) 49.5mm
Maximum Box Cutting Capacity
45O(3mm wall) 32mm
Optimum Cutting Thickness (Mild Steel Plate)
6mm
RPM No Load (min-1) 4500
Recommended Maximum Duty Cycle 30mins
Blade Diameter: 180mm
Bore Diameter: 20mm
Thickness: 2mm
Noise and Vibration Data
Sound pressure level: 95.5 dB(A) K 3 dB(A) Sound
power level: 104.3 dB(A) K 3 dB(A)
Vibration level: 4.99m/s2 K 1.5m/s2
The declared vibration total value has been
measured in accordance with a standard test
method and may be used for comparing one tool
with another.
The declared vibration total value may also be used
in a preliminary assessment of exposure.
WARNING: The vibration emission during actual use of
the power tool can differ from the declared total value
depending on the ways in which the tool is used. The
need to identify safety measures and to protect the
operator are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of the
operating cycle, such as the times the tool is switched
off, when it is running idle, in addition to trigger time).
ADDITIONAL SPECIFIC SAFETY RULES GB
SPECIFICATION GB

8www.evolutionsteel.com
ASSEMBLY
Your Evolution Power Tools saw is shipped
complete. Remove all contents from the box and
inspect to ensure no damage was incurred during
shipping, and that the items listed below are
included.
ITEMS SUPPLIED
Description
Instruction Manual: Qty 1
Allen Key: Qty 1
180mm Steel Blade (tted) Qty 1
Discharge Port Exhaust Qty 1
Parallel Edge Guide Qty 1
Carry Case Qty 1
ASSEMLY GB

9
www.evolutionsteel.com
E VO180
1. ON/OFF TRIGGER SWITCH
2. AUXILLARY FRONT HANDLE
3. DISCHARGE EXHAUST PORT
4. LOWER BLADE GUARD
5. FITTED BLADE IN SITU
EVO 180MM STEEL CIRCULAR SAW
MACHINE OVERVIEW GB
1
2
3
4
5

10 www.evolutionsteel.com
GETTING STARTED
WARNING: Always disconnect the saw from the
power source before making adjustments.
Refer to the “Service Parts Diagram”. Install a blade
as detailed in the “Installing or Removing a Blade”
section.
WARNING: Never start the saw with the cutting
edge of the saw blade in contact with the workpiece
surface. Do not retract blade guard manually. Guard
retracts automatically.
This saw is equipped with an approved cord and
plug for its intended Country of use. Do not alter or
modify the power cord.
Installing or Removing a Blade
WARNING: Only use genuine Evolution blades
which are designed for this machine. Ensure that
the maximum speed of the blade is compatible with
the machine. Only perform this operation with the
machine disconnected from the power supply.
Note: It is recommended that the operator
considers wearing protective gloves when handling
the blade during installation or when changing the
machines blade.
1. Place saw on a level, secure surface.
2. Remove the chip collector from the machine by
undoing the (2) large thumb screws. (Fig. 1)
Note: The chip collector thumb screws are ‘captive’
and cannot be removed from the machine.
3. Lock the machine arbor by engaging the arbor
lock. (Fig. 2)
4. Using the supplied Allen Key loosen and remove
the arbor socket headed screw and outer blade
drive ange. (Fig. 3)
5. Remove the saw blade.
6. Thoroughly clean inner and outer blade drive
anges and blade mounting surface before
installing a new blade.
7. Ensure that the direction of rotation arrows
printed on the blade, match the direction of rotation
arrow found on the chip collection cover. (Fig. 4)
8. Reinstall the outer drive ange and the arbor
socket headed screw.
9. Engage the arbor lock and tighten the arbor
socket headed screw securely using the Allen key.
Note : The socket headed arbor screw has a RH
thread.
GETTING STARTED GB
FIG 1
FIG 2
FIG 3

11
www.evolutionsteel.com
E VO180
10. Replace the chip collector and securely tighten
the two thumb screws.
11. Check that the arbor lock is fully released by
manually rotating the blade.
12. Check the operation of the safety guard.
Parallel Edge Guide
A parallel guide (for help when rip cutting) can be
tted to the sole plate of the machine The guides
arms should be inserted into the rectangular slots in
the turned up edges of the sole plate, and slid under
the locking thumb screws. (Fig. 5)
Note: The edge guide can be tted to either side
of the sole plate and should only be tted and
adjusted with the machine disconnected from the
power supply.
Adjust the edge guide so that it is at the required
distance from the blade and tighten the two thumb
screws. Check that the edge guide is parallel to the
saw blade.
Adjustment of the Cutting Depth
Release the Lever Lock to adjust to the required cutting
depth. In most cases depth should be set at maximum
unless there are obstructions below the work surface.
Tighten the Lever Lock securely to lock in the required
position.
Adjustment of the Cutting Angle (Fig. 6)
1. Loosen the Bevel Locking Screw found at the
front of the saw.
2. Loosen the Rear Bevel Locking Screw found at
the rear of the machines sole plate.
3. Tilt the blade to the required angle. (Fig. 7)
4. Tighten both Bevel Locking Screws securely
Note: An angle scale (0O- 45O) is incorporated into
the Bevel Locking quadrant to aid setting.
Operating Advice
Carry out routine safety checks each time you
use the machine. Check that all safety guards are
operating correctly, and that all adjustment handles/
screws are tightened securely.
Check that the blade is secure and installed
correctly. Also check that it is the correct blade for
the material being cut.
Check the integrity of the power cord.
Always clamp the workpiece to a rigid support such
as a bench or saw horse whenever possible.
FIG 4
FIG 5
FIG 6

12 www.evolutionsteel.com
ON/OFF Trigger Switch
This machine is equipped with a safety start trigger
switch.
To start the machine:
• Push in the safety lock button on the side of the
handle with your thumb.
•Depress the main trigger switch to start
the motor. (Fig. 8)
Chip Collector
This machine is tted with a chip collector to
capture metal chips. The chip collector cover plate
is provided with a transparent ‘window’ so that the
operator can see the contents and empty when
necessary.
To remove and empty the chip collector:
• Loosen the two chip collector thumb screws.
• Ease the chip collector from the machine.
• Empty the contents of the chip collector by
tipping the collector upside down over a suitable
waste container, allowing the contents to fall out.
Note: To maintain operational efciency we
recommend that the collector is emptied when
approximately 60% full. Dispose of the contents of
the chip collector in an environmentally responsible
manner.
• Replace the chip collector and securely tighten
the (2) thumb screws.
Discharge Port
When cutting wood the Discharge Port Exhaust
should be tted to the chip collector cover
Discharge Port.
To t the Discharge Port Exhaust
• Remove the Discharge Port blanking cover by
unscrewing the cross headed screw.
• Pull the blanking cover from the
Discharge Port and safely store for future use.
• Fit the Discharge Port Exhaust in place of the
blanking cover. (Fig. 9) Wood chips will be ejected
from the Discharge Port Exhaust during cutting
operations.
When cutting has been completed, remove the
Exhaust Port and replace the blanking cover and
tighten the xing screw securely.
FIG 7
FIG 8
FIG 9

13
www.evolutionsteel.com
E VO180
Cutting Advice
The operator should wear all relevant PPE (Personal
Protection Equipment) necessary for the job at
hand. This could include safety glasses, dust
masks, safety shoes etc.
The operator should always be aware of the position
and routing of the power cable.
• Do not force the machine.
• Allow the speed of the saw blade do the work.
Cutting performance will not be improved by
applying excessive pressure to the machine, and
blade life will be reduced.
• When using the parallel edge guide, ensure that it
is parallel with the blade. The blade and/or motor
could become damaged if the machine is used
with an incorrectly adjusted parallel edge guide.
• To set the guide, loosen the two retaining screws,
and adjust the guide to the required position.
Tighten the locking screws.
• Place front edge of sole plate squarely on the
workpiece before starting the motor.
• When starting a cut, sight the cutting line with
the line of cut guide, taking care to introduce the
blade to the material slowly, so as not to damage
its teeth.
• Use both hands to move the saw forwards rough
the work piece.
• Apply smooth, constant pressure to move the
saw forwards through the workpiece.
When a cut has been completed release the ON/
OFF trigger switch and allow the blade to come to
a complete halt. Do not apply lateral pressure to
the blade disc in an attempt to slow it down more
quickly.
WARNING: If the motor should stop or stall whilst
a cut is being attempted release the trigger switch
immediately and disconnect the machine from
the power supply. Remove the machine from the
workpiece before investigating the cause and
attempting to restart the motor.
Note: This saw is tted with an overload protection
device. This is designed to prevent overloading and
consequent damage to the motor. If this feature
‘trips’, the motor stops and will not operate.
Allow the machine to cool down and then press the
‘reset switch’ at the base of the main handle.
MAINTENANCE
Note: Any maintenance must be carried out with
the machine switched off and disconnected from
the power supply.
Check that all safety features and guards are
operating correctly on a regular basis. Only use
this machine if all guards/safety features are fully
operational.
All motor bearings in this machine are lubricated for
life. No further lubrication is required.
Use a clean, slightly damp cloth to clean the plastic
parts of the machine. Do not use solvents or similar
products which could damage the plastic parts.
WARNING: Do not attempt to clean by inserting
pointed objects through openings in the machines
casings etc. The machines air vents should be
cleaned using compressed dry air.
Excessive sparking may indicate the presence of
dirt in the motor or worn out carbon brushes.
Brush Checking and Replacement
To replace the motor brushes:
• Disconnect the machine from the power supply.
• Place the machine on a level, secure surface.
• Remove the (2) motor brush retainer cap screws.
• Withdraw the brushes.
Note: If the Carbon rod is less than 6mm long or if
there are signs of burning or damage, replace the
brushes.
• Fit the new brushes.
• Ret the motor brush retainer caps.
• Run the saw without load for several minutes
after brush replacement to aid the ‘bedding in’
process.
MAINTENANCE GB

14 www.evolutionsteel.com
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority or
retailer for recycling advice
ENVIRONMENTAL PROTECTION GB

15
www.evolutionsteel.com
E VO180
EVO180
F11100

®
www.evolutionpowertools.com