Exmark Football Toss Wall Manual

Supply List
LUMBER:
HARDWARE:
TOOLS:
One (1) box of 1 ½" #10 deck screws | One (1) box of 2 ½" #10 deck screws
Six (6) ¼"-20x4" carriage bolts | Six (6) ¼" at washers | Six (6) ¼"-20 wing nuts
Tape measure | T-square | Power drill with drill and Phillips head bits
Circular saw | Router with cutting bit or jigsaw with wood-cutting blade
Five (5) 8-foot 2x4s | One (1) 12-foot 2x4 | One (1) sheet of 4'x8'x½" plywood
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions

1. Build 4' wide x 8' tall frame using three (3)
8-foot 2x4s. Use two (2) 8 footers for frame
height, and cut one (1) 8' into two (2) 44 7/8"
sections for frame width.
2. Afx four (4) frame pieces with 2 ½" #10
deck screws (two at each of four corners).
3. Cut two (2) 8" 2x4 sections to use as
spacers for top arm of game support. Drill a
9/32" hole in the center of both 8" sections
and countersink for a ¼"-20x4" carriage bolt.
BUILD INSTRUCTIONS
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions

4. Afx two (2) 8" sections (to center) 63 5/8"
from bottom of frame. (See Diagrams 1-Side
and 1-Back.)
5. Afx full sheet of 4'x8'x½" plywood to 4'x8'
frame with 1 ½" #10 deck screws.
6. Draw and cut three (3) 14" diameter holes (at
locations of your choice) in the plywood.
7. Construct bottom (ground) support by using
two (2) 48" 2x4s and one (1) 42" 2x4, fastened
with two (2) 2 ½" # 10 decking screws on both
sides. (See Diagrams 2 and 2A.) Note: Notch
both 48” sections (both sides at 45-degree
angles) at the ends that attach to the 4'x8'
frame.
BUILD INSTRUCTIONS
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions

8. Attach ground support to 4'x8' with two
(2) ¼"-20x4" carriage bolts, at washers
and wing nuts.
9. Cut two (2) 72 3/8" 2x4s to use as back
supports between ground support and 4'x8'
frame, with 9/32" holes drilled 1 3/16" down
and 2 3/8" left from top of each support arm
(same hole positioning should be drilled on
both sides of each arm support). Attach tops
to 4'x8' frame spacers and at back ends of
ground support.
10. Paint/decorate outward facing side of
plywood . . . And, get into the game!!
BUILD INSTRUCTIONS
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions

BUILD DIAGRAMS
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions
8"
8"
63 5/8"
DIAGRAM 1 - SIDE
DIAGRAM 1 - BACK
96"
44 7/8"
13/4"
3 5/8"

BUILD DIAGRAMS
CARE INSTRUCTIONS
‘Get In The Game’ Football Toss Wall
Supply List and Build Instructions
If football toss wall will be stored outside, treated lumber is recommended.
42"
48"
11"
DIAGRAM 2
DIAGRAM 2A
11"
42"
48"
3 5/8"
1 15/16"
1 3/4"
1 3/4"