ItsaGoal ASTSTARTQUICKGOAL 12' X 6' MINI-SOCCER User manual

FITTING
INSTRUCTION
TEL: [phone]
12' X 6' MINI-SOCCER
Multi-Surface - One section crossbar.
FOR A FAST START - Lift the goal into postilion
and unfold the side frames, click
the back bar in, insert ground
anchors and you’re ready
to start the game.
STORAGE
The goal can be
folded flat for
easier storage
after games.
Note : Make sure part C, blanking Cap
is inserted in the corner bracket X with
the 8 holes. This part may already be
inserted.
X
C
H
A
H
I
Locking Pin
Arrowhead net fixing
DO NOT THROW THE
LOCKING PINS AWAY
Insert net hooks in holes on
crossbar/uprights and insert pins to lock
IF GOALS HAVE
INTENSIVE USE ADD
THE ADDITIONAL NET TIES
TO THE GROUND BASE FRAME
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
GOAL POSTS MUST BE ANCHORED AT ALL TIMES
Optional longer pegs are available for use on sandy ground. On grass, a
risk assessment of soil and weather conditions suitability should be
carried out when anchors or counter weights are to be used.
Extra anchors are available TEL: [phone]
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD,
ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS
IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE
MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
PLEASE NOTE :
THE NET TIES
CAN BE USED TO
TIE THE NETS TIGHTLY
INTO THE CORNERS
FOR A BETTER FIT.
A
E
X
A
E
68mm
68mm
68mm
68mm
40mm
40mm
4
4
2
3
2
8
12
x
2
2
2
2
1
1
x
x
x
x
x
x
x
x
x
x
x
x
CORNER BRACKET 4 HOLES
SPIGOT
BLANKING CAP
MULTI-SURFACE ANCHOR
GROUND PEG
STANCHION ELBOW
SMALL QUICK RELEASE BUTTON
CROSSBAR SECTION
3628mm LONG - 68mm Diameter
BACKBAR SECTION
3628mm LONG - 68mm Diameter
SIDEBAR SECTION
1360mm LONG - 68mm Diameter
UPRIGHT SECTION
68mm Diameter
TOP STANCHION TUBE
400mm LONG - 40mm Diameter
BACK STANCHION TUBE
1896mm LONG - 40mm Diameter
LARGE QUICK RELEASE BUTTON
POST SECTIONS
A
B
C
D
L
M
N
O
P
E
F
H
I
Q
COMPONENTS
6
x
NET TIE
STANCHION TIE
J
JS
32
12
x
x
LOWER BACK STANCHION
CONNECTOR
G2
x
1
x
GOAL NET 12' x 6'
24
x
ARROW HEAD NET FIXING
with attached LOCKING PIN
K
NET
CARE & MAINTENANCE - see separate sheet supplied or
visit www.itsagoal.net for additional copies. Our goalpost if used correctly
will last many years. We do also offer a full spare part service
and if your goals need refurbishment this can be arranged
2
x
CORNER BRACKET
UPRIGHT 8 HOLES
X
2
x
FOLDING BRACKET
FB
FASTSTARTQUICKGOALTM
OPTIONAL - STANCHION TIES
OPTIONAL - Stanchion Net Ties
J
JS

K
STEP BY STEP ASSEMBLY
STEP 2
Insert Blanking Cap part C and
insert Large Quick Release Button H (x2)
into Corner Bracket X.(NOTE: CornerBracket X
is different from Corner Bracket A. Corner
Bracket X is to be fitted into the upright posts
and has 8 holes.
STEP 4
Insert Small Quick Release
Black Button I into the Spigot B.
Insert Spigot B and insert H (x2)
into two of the Corner Bracket A.
(NOTE: Corner Bracket A
has 4 holes for locks)
STEP 3
Insert Blanking Cap part C and
insert Large Quick Release Button
H (x2) into Corner Bracket A.
(NOTE: Corner Bracket A has
4 holes.)
STEP 6
Insert Corner Brackets X into the
upright posts O (uprights have logos on the side)
STEP 7
Insert Corner Brackets A into
each end of the crossbar L
STEP 8
Insert Corner Brackets A into
each end of the Backbar M
STEP 9
Attach Side bars N to
the ground back bar by slotting
into the corners brackets
STEP 10
Insert part I (locking button)
into FB and connect Folding
Bracket FB on the upright
posts. Attach Uprights O
to the Side bars N
STEP 11
Attach Crossbar L
to uprights O
STEP 5
Insert Arrow Head Net Fixings K
into Upright Posts and Crossbar.
DO NOT THROW AWAY
LOCKING PINS
FB
FB
X
C
H
C O R N E R
BRACKET
C O R N E R
BRACKET
H
A
C O R N E R
BRACKET
SPIGOT B
I
L
O
X
STEP 12
Join top tubes P to elbows F
and back tubes Q and connect to the goalpost
STEP 13
Attach Ground Anchors
see details of use overleaf..
STEP 14
Attach The Net to the
Net Fixings. Start with
each corner
TIE A CORD BETWEEN THE
TOP SUPPORT TUBES TO
SUPPORT THE ROOF OF THE
NET (THIS CAN BE LEFT TIED
IN POSITION WHEN
DISMANTLED)
FOR EASIER ASSEMBLY Use a rubber mallet and also spray furniture polish inside posts. Do not use a metal hammer. Do not apply grease or vaseline.
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTS, ALL RIGHTS RESERVED A REGISTERED DESIGN
A
L
H
I
A
H
C
P
F
Q
OPTIONAL - Net ties are ideal
fit nets tightly to the side
stanchions. This is ideally
when nets are left attached to
the fully assembled side
frames.
FOR A FAST START - Lift the goal into postilion
and unfold the side frames, click
the back bar in, insert ground
anchors and you’re ready
to start the game.
STORAGE
The goal can be
folded flat for
easier storage
after games.
FASTSTARTQUICKGOALTM
STEP 1 Lay out POSTS and
Components shown on page 1
CROSSBAR &
BACKBAR 3628mm
SIDEBARS
1360 mm
UPRIGHTS
TOP
STANCHION
400 mm
BACK
STANCHION
1896 mm
LM
N
O
P
Q
A
M
G

 NOTE: If your net does not fit the first time,
you may be fitting it to the goal frame upside
down i.e. that is to say the net from the crossbar to
the floor (a) is longer than the length of the net to
the bottom of the upright.(b)
STEP BY STEP NET FITTING
ANCHORING YOUR GOAL
STEP 1
Open net and check the lengths of a and b
correspond with the diagram below.
STEP 3
Attach the corners first, where the upright
posts meets the crossbar as shown.
Then attach the net to the post using
the Arrow head net
fixings on crossbar
and uprights.
STEP 4
Using the large net ties tie the
net to the ground side frame
back ground frame.
STEP 5
Using the small net ties
attach the net down the
back of the sloping
back net supports as
shown to the posts
as shown.
STEP 6
NET CORD - ROOF TO THE NET
To help define the roof of the net Tie the
cord to one side and pull the net chord
tight and wrap neatly down and around
the stanchion section.
If you are regularly attaching or detaching
the net then apply coloured tape to the
roof corners of net to help identify the
roof area.
STEP 2
With the net the correct way round
lift the net onto the goalpost frame.
This is easier with two people.
a
b
a
b
NET
CHORD
OPTIONAL - STANCHION TIES
9
10
GROUND
PEG REMOVAL
D
E
USE THE HOOK ON THE END
OF THE RED GROUND PEG
TO REMOVE PEGS FROM THE GROUND OR USE
A CLAW HAMMER FOR PEGS THAT ARE
DIFFICULT TO REMOVE.
WARNING: Check the position of any underground services before using
the ground anchors and pegs. We take no responsibility for any damage
or injury caused in this manner.
HARD SURFACES: to prevent damage to goal or it's components, loosen
soil with a steel pole and moisten with some water before inserting the
ground anchors. Do not use the goal in sub zero temperatures.
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A
LEVEL PLAYING SURFACE. PLACE THE MULTI-SURFACE ANCHOR OVER
EACH SIDE OF THE GROUND FRAME (POSITIONS SHOWN) HAMMER THE
PEGS THROUGH THE HOLES (DO NOT USE METAL HAMMERS USE
RUBBER MALLETS) ON THE ANCHOR DOWN UNDER THE FRAME INTO
THE GRASS ADDITIONAL ANCHORS OR LARGER PEGS CAN BE
PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE ANCHORS
CAN BE USED FOR HARD SURFACES SUCH AS TARMAC WITH
OPTIONAL BOLTS. ON HOT/SUNNY DAYS TARMACADAM SOFTENS AND
THEREFORE TO ANCHOR
YOUR GOAL PROPERLY YOU MUST:-
1 DIG HOLES IN YOUR TARMAC FILL HOLES WITH CONCRETE
2 DRILL TWO 14MM HOLES 12CM APART AND 70MM DEPTH.
3 POSITION GOAL AND ANCHOR, INSERT AND TIGHTEN BOLT.
FOR OTHER SURFACES SUCH AS WOODEN SPORTS HALL FLOORS
WOOD SCREWS (INSTEAD OF BOLTS) OR COUNTER BALANCE
WEIGHTS CAN ALSO BE USED (SUPPLIED SEPARATELY).
INSERT MULTI-SURFACE
ANCHOR PEGS FULLY
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
LONGER GROUND PEGS ARE AVAILABLE SEPARATELY.
200mm
STANDARD
300mm
SOFTER GROUND
Longer pegs are to be used on sandy or
Soft ground earth. A risk assessment of soil
conditions suitability should be carried out when
anchors are to be used.
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD,
ALL RIGHTS RESERVED A REGISTERED DESIGN
SPARE PARTS
TEL: [phone]
For help contact www.footiegoals.com

CORNER BRACKETS
At the end of the season nets can be tied into a bundle and placed into a pillow case (not to damage washing
machine) and washed at 40 C0 with normal washing powder. The ground frame can be washed with hot
soapy water. Any scuff marks on posts can be rubbed off with a light abrasive scouring pad.
WARNING: Check the position of any underground services before using the ground anchors and pegs. We
take no responsibility for any damage or injury caused in this manner. NEVER use the goals without the
ground anchor system. In severe weather or windy conditions it is advisable to take your goal down as
damage is not covered by the guarantee in such circumstances. If you find the nets are worn along the floor
it may be rodents, by spreading pepper along the base frame rodents will be deterred. It is advisable in any
contact sport to take out the relevant insurance's to cover against injury both from taking part, equipment
and other unforeseeable circumstances. Crossbars will not be replaced within the guarantee period if broken
by swinging or climbing or any other misuse. DO NOT try to glue any damaged fixings. Plastic materials in
this product vary and this may cause the plastic to break. Always replace any damaged components.
SQUARE MESH Net is cut to shape. Simply throw over the frame and fit each end
onto top stanchion by securing on each corner of crossbar. NOTE: If your net
does not fit the first time, you may be fitting it to the goal frame upside down i.e.
that is to say the net from the crossbar to the floor (a) is longer than the length of
the net to the bottom of the upright.(b)
a
b
a
b
We advise adult supervision during assembly and use. Observe and follow
warning labels attached to goal. Do not use any components, nets or parts
if they are damaged or broken. Spare parts and replacement nets are
readily available. If others are to install your goal you should show them
how to erect and dismantle the goal and hand them a copy of the fitting
instruction. If you lose your instructions copies can be attained from our
company website. To avoid damage when dismantling the goal follow
these guidelines: it is advisable in extreme windy conditions to dismantle
the goal and store away. Do not drop any heavy objects on ends of tubes.
When dismantling the goal ensure that all fittings are packed away and
that non are left on the playing surface. Warning goals must never be left
up or used unless they are properly fitted with ground anchors with net
attached and securely pegged down.
Do not use the goal in sub zero temperatures. warning labels should be
replaced when worn and we recommend replacing them every two years -
spare labels available. damaged components requested under guarantee
must be returned for inspection. Failure to follow the warnings, fitting
instructions contained in this document, may invalidate your guarantee.
The company , its agents and representatives do not accept any product
liability if used outside the EU. Use of the product in other countries outside
the EU including the USA is not covered and appropriate insurance should
be taken out by the user to cover for any eventuality. We reserve the rights
to amend the specifications of our soccer products in the interest of
continued development. Your product therefore may differ slightly to those
illustrated. Not suitable for children under 36 months until assembled due
to small parts.
TEL: [phone]
SPARE PARTS
NET TIES
!
1
TEETH
3
2
NET CORD
4
6
7
8
Ensure the teeth of the
Net tie are facing you
(see step 1).
Loop the Net Tie around
the Net Cord and slide
the end into the
horizontal slot and pull
tight onto Net Cord (see
step 1- 2).
The vertical slot of the
Net Tie is used to
secure the net to the
post. Loop the Net Tie
around the post and
insert through
vertical slot and twist to
lock. (steps 3 - 5).
Any excess Net Tie can
looped back into the
vertical slot. This will
also secure the net tie in
a fixed position (steps 6
- 8). If Net Ties are to be
removed after use then
do not loop back into
vertical slot.
5
POST SECTION
PULL
TIGHT
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL, ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Ensure locking pin
Is inserted Fully in
the posts
DO NOT THROW THE PINS AWAY
3
Push locking pin
Down centre of
Arrow Head
2
Insert Arrow Head
into Holes on
posts
1
Push and Lock the
spigots to two of
the four Corner
Brackets.
Push and Lock the
Blanking Caps to the
two remaining Corner
Brackets. (already
Push and Lock the
Large Quick Release
Buttons into the ends
o f t h e C o r n e r
Brackets.
Push and Lock the
S m a l l Q u i c k
Release Buttons
into the ends of the
NOTE : All plastic extrusions vary and therefore some tubes may be looser
or tighter to connector fittings. If you want to increase the diameter of the
fitting just wrap masking tape around the part that fits into the tube, twist
as you insert the fitting and it will grab to the tube tight ...you can make
tighter fits by adding more tape.
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
ANCHORING YOUR GOAL
WARNING: Check the position of any underground services before using the ground anchors and pegs. We
take no responsibility for any damage or injury caused in this manner.
HARD SURFACES: to prevent damage to goal or it's components, loosen soil with a steel pole and moisten
with some water before inserting the ground anchors. Do not use the goal in sub zero temperatures.
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE. PLACE THE
MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS SHOWN) HAMMER THE
PEGS THROUGH THE HOLES (DO NOT USE METAL HAMMERS USE RUBBER MALLETS) ON THE ANCHOR
DOWN UNDER THE FRAME INTO THE GRASS ADDITIONAL ANCHORS OR LARGER PEGS CAN BE
PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE ANCHORS CAN BE USED FOR HARD
SURFACES SUCH AS TARMAC WITH OPTIONAL BOLTS. ON HOT/SUNNY DAYS TARMACADAM SOFTENS
AND THEREFORE TO ANCHOR YOUR GOAL PROPERLY YOU MUST:-
1 DIG HOLES IN YOUR TARMAC FILL HOLES WITH CONCRETE , 2 DRILL TWO 14MM HOLES 12CM APART
AND 70MM DEPTH. 3 POSITION GOAL AND ANCHOR, INSERT AND TIGHTEN BOLT.
FOR OTHER SURFACES SUCH AS WOODEN SPORTS HALL FLOORS WOOD SCREWS (INSTEAD OF BOLTS)
OR COUNTER BALANCE WEIGHTS CAN ALSO BE USED (SUPPLIED SEPARATELY).
INSERT MULTI-SURFACE
ANCHOR PEGS FULLY
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)