Extech Instruments 381395 User manual

i
User Manual
Model 381395
5MHz Dual Channel
True RMS Oscilloscope Datalogger
FUNC
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
Back to the Extech 381395 Product Page
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
FAX [phone] - TestEquipmentDepot.com

ii
Table of Contents
1. GENERAL INFORMATION 1-1
1.1. FEATURE OVERVIEW 1-1
1.1.1. Universal SCOPE Mode 1-1
1.1.2. DATA Logger 1-1
1.1.3. Digital Multi-Meter 1-2
1.1.4. Frequency Counter 1-2
1.1.5. General 1-2
1.2. WARRANTY INFORMATION 1-3
1.3. PRECAUTIONS 1-3
1.4. MAINTENANCE 1-3
1.5. SAFETY INFORMATION:READ FIRST 1-4
1.6. SYMBOLS AND TERMS 1-4
1.7. UNPACKING THE INSTRUMENT 1-5
1.7.1. Standard 1-5
1.7.2. Options 1-5
2. PRODUCT DESCRIPTION 2-1
2.1. THE INPUT TERMINAL AREA 2-2
2.1.1. Caution ( ) 2-2
2.1.2. Warning ( ) 2-2
2.1.3. 600V MAX 2-2
2.1.4. The METER provides 4 input jacks 2-2
2.2. THE KEYS AREA 2-3
2.2.1. Turning power on and off ( ) 2-3
2.2.2. AUTO key ( ) 2-3
2.2.3. TRIGger key ( ) 2-3
2.2.4. Function key ( ) 2-4
2.2.5. Command menu keys ( ) 2-4
2.2.6. Four arrow keys ( ) 2-5
2.2.7. Display back light ( ) 2-6
2.2.8. Hold key ( ) 2-6
2.3. THE DISPLAY AREA 2-7
2.3.1. Special indicator 2-7
2.3.2. DISPLAY depends on selected function 2-8
2.3.3. The Command Menu 2-15

iii
2.4. THE USB INTERFACE AND POWER INPUT TERMINAL 2-16
2.4.1. USB INTERFACE 2-16
2.4.2. Power Adaptor Input Terminal 2-16
3. USING THE SCOPE 3-1
3.1. POWERING THE METER 3-1
3.2. DISPLAY BACKLIGHT 3-1
3.3. SELECTING “GENERAL SCOPE” IN THE MENU 3-1
3.4. SELECTING ITEMS IN SCOPE SETUP MENU 3-2
3.4.1. Set Frequency measurement for CHA 3-2
3.5. CHANGING THE GRAPHIC REPRESENTATION 3-3
3.5.1. Changing the vertical division 3-3
3.5.2. Changing the Horizontal division (Time Base) 3-3
3.5.3. Positioning the Waveform of CH A on the Screen 3-4
3.5.4. Positioning the Waveform of CH B on the Screen 3-4
3.5.5. Positioning the Trigger Point Indicator on the Screen 3-4
3.6. ACQUIRING THE WAVEFORM 3-5
3.6.1. Recording slow signals over a Long Period of Time. 3-5
3.6.2. Selecting AC-Coupling for INPUT A 3-5
3.7. TRIGGERING ON A WAVEFORM 3-6
3.7.1. Setting Trigger mode (Tmode) 3-6
3.7.2. Setting AUTO Trigger Level 3-7
3.7.3. Setting Normal Trigger mode 3-8
3.7.4. Setting Trigger Slope 3-8
3.7.5. Changing the Trigger level Indicator 3-8
3.7.6. Making a single acquisition 3-9
3.8. STORING AND RECALLING SCREENS 3-9
3.8.1. Storing Screen 3-9
3.8.2. Recalling Screen 3-10
4. USING THE DATA LOGGER 4-1
4.1. SELECTING ITEMS IN DATA LOGGER SETUP MENU 4-1
4.1.1. Changing the Sampling Type 4-1
4.1.2. Changing the Sampling interval Time 4-2
4.1.3. Changing the Start/Stop Address 4-2
4.2. DATA LOGGER 4-3
4.2.1. Changing the Measurement Function & Range 4-4
4.3. RECALL DATA 4-4
5. USING THE DIGITAL MULTIMETER 5-1
5.1. THE DIGITAL MULTIMETER DISPLAY MODE 5-1

iv
5.1.1. RECORD MODE 5-1
5.1.2. RELATIVE MODE 5-1
5.1.3. COMPARE MODE 5-2
5.1.4. TREND PLOT 5-2
5.2. MEASUREMENT PROCEDURES 5-3
5.2.1. DC V 5-3
5.2.2. AC V 5-4
5.2.3. Resistance 5-5
5.2.4. Continuity 5-5
5.2.5. Frequency 5-6
5.2.6. RPM 5-6
5.2.7. Pulse Width 5-7
5.2.8. Duty 5-7
6. SYSTEM SETUP 6-1
6.1. CONFIGURE THE AUDIBLE BEEPER 6-1
6.2. AUTO POWER OFF 6-1
6.3. SET THE BAUD RATE (BPS) 6-1
6.4. CHANGE THE CURRENT DATE AND TIME 6-2
6.4.1. Setting the time 6-2
6.4.2. Setting the date Error!
Bookmark not defined.
7. SPECIFICATIONS 7-1
7.1. GENERAL SPECIFICATIONS 7-1
7.2. TECHNICAL SPECIFICATIONS 7-2
7.2.1. General Oscilloscope Function Specs. 7-2
7.2.2. Data Logger Function Specs. 7-3
7.2.3. Digital Multimeter Function Specs. 7-3
8. REMOTE PC INTERFACE 8-1
8.1. USB HID DEVICE INSTALLATION 8-1
8.1.1. System Requirements 8-1
8.1.2. Operating System 8-1
8.2. PC USB PORT CONNECTION 8-1
8.2.1. HID Device 8-1
8.3. INSTALLING WINDOWS APPLICATION SOFTWARE 8-2
8.4. RUNNING THE APPLICATION SOFTWARE 8-3
8.4.1. Oscilloscope Mode 8-3
8.4.2. DMM & Data Logger Mode 8-4
8.4.3. Display Mode for DMM & Data Logger Mode 8-5

v
9. MAINTAINING THE METER 9-1
9.1. SECTION OVERVIEW
ERROR!BOOKMARK NOT DEFINED.
9.2. STATIC SAFE HANDLING 9-1
9.3. CLEANING THE METER 9-1
9.4. STORING THE METER 9-2
9.5. CALIBRATION 9-2
9.6. REPLACING AND DISPOSING OF THE LI-ION BATTERY 9-2
9.6.1. Replacing the battery pack 9-3
10. APPENDICES 10-1
10.1. TROUBLESHOOTING GUIDE 10-1
10.2. LCD STATUS INDICATION BY FUNCTION 10-2
10.2.1. Function Menu & General Scope Mode 10-2
10.2.2. Data Logger Mode 10-2
10.2.3. Multimeter / Record Mode 10-2
10.2.4. Multimeter / Relative Mode 10-3
10.2.5. Multimeter / Compare Mode 10-3
10.2.6. Multimeter / Trend Plot Mode 10-3
10.2.7. System Setup Mode 10-4
10.2.8. Trigger Setup Mode 10-4

1. General Information
Model 381395 Version 1.0 January 2008
1-1
1. General Information
This section contains general Meter information. The bulleted list below outlines the section.
zFeature Overview
zWarranty Information
zSafety Information
zSymbols and Terms
zSpecifications
zUnpacking the Test Tool Kit
1.1. Feature Overview
The Model 381395 is a handheld, battery-operated Oscilloscope, True RMS Data Logger
and Digital Multimeter designed and tested according to IEC Publication 1010-1 (EN 61010-
1:1993, Over voltage Category II)
This instrument features:
1.1.1. Universal SCOPE Mode
zDual Channel with Auto Calibration
zSampling Time
Single CH mode: 50 MS/s, Dual CH mode: 25 MS/s
zDC to 5MHz Oscilloscope bandwidth
z16 shot waveform and setup memories
zAutomatic Triggering
zAutomatic setting for horizontal and vertical divisions
zRoll and Single shot modes
zExcellent internal noise reduction
zReal time Updates
1.1.2. DATA Logger
zLogger Memory: 17,000 Data Points
zLogs the following signal types: DCV, ACV, OHM, BZ, Hz, RPM, P/width, Duty
zPrints programmed intervals in Hours/Minutes/Seconds
zAppends incoming data to existing data

1. General Information
Model 381395 Version 1.0 January 2008
1-2
zSampling Rate: 0.25S/s
zSampling intervals from 1 second to 9,999 seconds
zSampling Mode: Peak and Sampling Time
zBuilt-in Real Time Clock (RTC)
zStart / Stop address setting
zData is retained when battery is low or has been removed
1.1.3. Digital Multi-Meter
zLarge 10,000 count LCD and fast 101 segment analog Bar Graph display
zProgrammable Function mode: Multi display measurements
Record (Max, Min, Avg), Relative (Ref, Err), Compare (GO-NOGO) mode and Trend plot
zReal Time for MAX or MIN, elapsed time for AVG
zMeter automatically selects best range instantly (Fast Auto range)
zData hold and run mode
zRPM, Duty cycle and Pulse width measurement
zTrue RMS digital Multi-meter
zMax. Voltage between Input and Ground: DC or AC 600Vrms
z600V Overload Protection
1.1.4. Frequency Counter
zFrequency Range: 0 to 10MHz
zAccuracy: ±(0.05%+5)
1.1.5. General
zEasy to Operate
zBacklit display with Low battery indication
zUSB PC interface for viewing and saving measurements and waveform data
zAuto power off (can be disabled)
zDisplay resolution: 132 x 128 pixels
zDesigned to comply with safety standards: UL3111 and CSA C22.2 No.1010-1

1. General Information
Model 381395 Version 1.0 January 2008
1-3
1.2. Warranty Information
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and
workmanship for one year from date of shipment (a six month limited warranty applies to sensors and
cables). If it should become necessary to return the instrument for service during or beyond the
warranty period, contact the Customer Service Department at [phone] ext. 210 for
authorization or visit our website www.extech.com for contact information. A Return Authorization
(RA) number must be issued before any product is returned to Extech. The sender is responsible for
shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty
does not apply to defects resulting from action of the user such as misuse, improper wiring, operation
outside of specification, improper maintenance or repair, or unauthorized modification. Extech
specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and
will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is
limited to repair or replacement of the product. The warranty set forth above is inclusive and no other
warranty, whether written or oral, is expressed or implied.
1.3. Precautions
zCarefully read the manual before operating this device
zThe contents of this manual may be amended by the manufacturer without notice
zNever dismantle the instrument
zThe equipment has been tested and calibrated before delivery
zThis product should be stored in a secured area
zThe rear protective terminal must be connected to actual earth ground otherwise electric
shock may occur.
1.4. Equipment Maintenance
zAlthough the equipment is durable and weather resistant, care should be taken not to
expose it to severe impact or pressure
zKeep the equipment clear of water and damp environments
zCalibration should performed once per year
zDo not operate this instrument if it appears damaged or if it functions abnormally
zDo not use the Meter near explosive gas or vapors
zTo clean, wipe the surface of the equipment with a dry and clean cloth

1. General Information
Model 381395 Version 1.0 January 2008
1-4
1.5. Safety Information: Read First
Warning!
Please read the following safety information before using the product. To avoid possible
electric shock or personal injury, please read and follow these guidelines carefully:
zFollow the guidelines in this manual and DO NOT use the Meter if the case is damaged
zDo not apply excessive voltage to the Multimeter. Apply voltage within the rated range
only
zUse caution when measuring voltages above 30V RMS, 42V peak, or 60V DC. These
voltages pose an electric shock hazard
zWhen using the probes always keep fingers behind the finger guards
zAlways connect the common test leads (black) before connecting the live test leads (red),
and disconnect the live test leads (red) before disconnecting the common test leads
(black)
zDisconnect circuit power and discharge all high-voltage capacitors before testing
resistance and continuity
zOnly qualified personnel should open the meter case
zWhen replacing fuses, use only the specified type and rating
zDo not try to operate the Meter if it is damaged. Disconnect the power from the equipment
and connect the point of purchase for return and repair information
1.6. Symbols and Terms
See explanation in manual before using this Meter. This symbol indicates hazards that
may cause damage to the instrument or may result in personal injury
This symbol indicates high voltage may be present. Use extra caution
Double Insulation (Protection Class II)
Recycling information
Equal potential inputs
High BNC Input
Earth (ground) terminal.
AC or DC
DC – Direct Current
AC – Alternating Current
Fuse
This product complies with the essential requirements or the applicable European laws
or directives with respect to safety, health, environment and consumer protections

1. General Information
Model 381395 Version 1.0 January 2008
1-5
1.7. Unpacking the Test Tool Kit
The product package is supplied with the following items:
1.7.1. Standard
zOne Meter
zTwo Test leads
zOne Lithuim-ION Battery (installed)
zOne AC Power & Rechargeable Adaptor
zOne CD (PC software)
zMeter to PC USB interface cable
zOne Carrying case
1.7.2. Options
zRubber Holster