Extraflame 00227596 User manual

STOVE AND PELLET INSERTS TECHNICAL MANUAL
MANUAL RESERVED FOR AUTHORISED AFTERSALES ASSISTANCE SERVICE
scheda elettronica - Mother board - carte életronique - elektronische steuerkarte - tarjeta eletronica
00227596 - 002272575  00227599

22

Index
3
INDEX
Control Board....................................................................................................................................................................... 4
Display icons key.........................................................................................................................................................................................................4
General menu ......................................................................................................................................................................... 5
User menU sTrUcTUre...............................................................................................................................................................................................5
user menu................................................................................................................................................................................. 6
teChnICIan menu.................................................................................................................................................................... 7
sTrUcTUre of The Technician menU................................................................................................................................................................7
General DaTa ................................................................................................................................................................................................................8
facTory seTTinGs.........................................................................................................................................................................................................8
DUcTeD DaTa...................................................................................................................................................................................................................9
insTaller...........................................................................................................................................................................................................................9
conTrols acTive.........................................................................................................................................................................................................10
chimney Type ................................................................................................................................................................................................................10
alarm memory reseT...............................................................................................................................................................................................11
oUTpUTs TesT.................................................................................................................................................................................................................11
coUnTers memories.................................................................................................................................................................................................12
DefaUlT ............................................................................................................................................................................................................................12
reseT parT hoUrs.......................................................................................................................................................................................................13
Unlock..............................................................................................................................................................................................................................13
VarIous Controls ...............................................................................................................................................................14
aTTivazione ...................................................................................................................................................................................................................14
sTove sTaTUs.................................................................................................................................................................................................................14
loaD....................................................................................................................................................................................................................................14
floW raTe conTrol..................................................................................................................................................................................................14
alarms ....................................................................................................................................................................................15
dIsplays ..................................................................................................................................................................................16
Components ..........................................................................................................................................................................17
maIntenanCe.........................................................................................................................................................................22
maIntenanCe.........................................................................................................................................................................24
posiTioninG UlTraWaTT carTriDGe....................................................................................................................................24
Components CompatIBIlIty..............................................................................................................................................25

4
DISPLAY ICONS KEY
Indicates the receipt of the radio signal
On = during radio communication
O = no radio communication
Fixed light = serial input deactivated
Indicates the status of the additional thermostat input (GND - I3)
It indicates functioning of the fumes motor.
O = ue gas motor deactivated
On = ue gas motor active
Flashing = breakdown
It indicates functioning of the ducted motor
O = Motor deactivated
On = Motor active
Flashing = the motor is running at minimum and in modulation
mode (additional input open)
It indicates functioning of the tangential fan (where present)
O = not working
On = working
Flashing = motor at minimum
Indicates the activation of the F1 function (future set-up)
O = function deactivated
On = function active
It indicates functioning of the pellet feed motor.
O = pellet feed motor deactivated
On = pellet feed motor active.
It indicates weekly programming functioning
Indicator on = Weekly programming active
Indicator o = Weekly programming not active
indicates the compensation function
O = the function is deactivated
On = the function is active
Indicates the stove modulation
On = the stove is working at the set power
Flashing = the power at which the stove is working is dierent to
the power set, the stove is modulating (for various reasons)
Indicates the contact of the external additional thermostat
closed contact: the contact of the external
additional thermostat is closed and
the STBY function is deactivated
Open contact: the contact of the external
additional thermostat is open and
the STBY function is deactivated
Flashing with closed
contact:
the contact of the external
additional thermostat is closed and
the STBY function is activated
Flashing with open
contact:
the contact of the external
additional thermostat is open and
the STBY function is activated
Indicates the presence of an alarm.
On: indicates the presence of an alarm
O: indicates the absence of alarms
Flashing: indicates the deactivation of the depression sensor.
Indicates the environment temperature status
O = the T° read by the probe is over the set temperature set
On = the T° read by the probe is below the set temperature set
Feed box probe
O = probe ok
On = broken probe (short circuit or open)
Flashing = tank cause modulation
CONTROL BOARD
BUTTON
ON/OFF
DISPLAY OF VARIOUS
TEXT MESSAGES
OPERATION
POWER ADJUSTMENT
TEMPERATURE
SETTING
TO ACCESS
THE MENU
CONTROL BOARD

P1 P4
P3
P2
P5
P6
P6
P1
P2 P3
P4 P5
P6
5
USER MENU STRUCTURE
GENERAL MENU
GO BACK  SAVE  EXIT
BROWSE PARAMETERS: NEXT P2 ; PREVIOUS P3
MODIFY SETTING DATA: INCREASE P4; DECREASE P5
CONFIRM  ACCESS MENU
SET CLOCK
SET CHRONO
LANGUAGE
USER
TECHNIC SET
CODE A0
GENERAL DATA
PARAMETER 05 FUMES SWITCHON
FACTORY CALIBRATION
PARAMETER 03 PELLET SWITCHON
INSTALLER
CONTROLS ACTIVE
CHIMNEY TYPE
CODE 77
OUTPUTS TEST
COUNTERS MEMORY
RESET PART HOURS
UNLOCK
CODE 77
DISPLAY
YEAR
MONTH
DAY
MINUTES
HOURS
ON/OFF CHRONO
REPEAT THE SAME PASSAGES FOR THE
OTHER 3TIME PERIODS
SET PRG1
07 40°C
MONDAY PRG1...
ONOFF
STOP PRG1
START PRG1
PELLETS
as %
V1FAN
TANGENTIAL VENTILATION
STAND BY
BUTTONS LOCK
IT,EN,FR,DE,ES
DEFAULT
CODE 01
CONFIRM
KEY 1
P6
P6
P6
P6
P2
P6
P6
P6
...SUNDAY PRG1
ONOFF
DAY
PELLET + /- %
FUMES MOTOR +/- %
V2 FAN
DUCTING AIR
SET CHANNELS RESET
ENCODER GAS MOTOR ON/OFF
DEBIMETER ON/OFF
IGNPLUG ON/OFF
SERIAL PORT ON/OFF
*ENCODER AUGER ON OFF
* ONLY WITH ELECTRONIC CARD 2272599
**ATTIVAZIONE
** AUTOMATIC DATE ACTIVATION STOVE

P2
P2
P2
P1 P4
P3
P2
P5
P6
P6
P1
P2 P3
P4 P5
P6
6
*for envisioned models
USER MENU
Menu SCROLLING TEXT VALUE FUNCTION
SET CLOCK
DAY MON...SUN Setting the day of the week
HOURS 00...24 Adjustment of the hour
MINUTES 00...59 Adjustment of the minutes
DATE 1...31 Adjustment of the date
MONTH 1...12 Adjustment of the month
YEAR 00...99 Adjustment of the year
SET CHRONO
ENABLE CHRONO OFF Activation/deactivation of the weekly programmer
START  PRG1 OFF  00:00 Time 1st ignition
STOP  PRG1 OFF  00:00 Time 1st switch-o
MONDAY PRG1 OFF ...SUNDAY PRG1 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG1 07  40°C Setting room temperature for the 1st time span
START  PRG2 00:10 OFF  00:00 Time 2nd ignition
STOP  PRG2 00:10 OFF  00:00 Time 2nd switch-o
MONDAY PRG2 OFF ...SUNDAY PRG2 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG2 07  40°C Setting room temperature for the 2st time span
START  PRG3 00:10 OFF  00:00 Time 3rd ignition
STOP  PRG3 00:10 OFF  00:00 Time 3rd switch-o
MONDAY PRG3 OFF ...SUNDAY PRG3 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG3 07  40°C Setting room temperature for the 3st time span
START  PRG4 00:10 OFF  00:00 Time 4th ignition
STOP  PRG4 00:10 OFF  00:00 Time 4th switch-o
MONDAY PRG4 OFF ...SUNDAY PRG4 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG4 07  40°C Setting room temperature for the 4st time span
LANGUAGE ITAL  ENGL  FRAN  DEUT  ESPA Selecting the language
USER
DISPLAY 10  31 Selecting display brightness
PELLET 30...+20 Selecting the percentage of pellet feed
V1FAN 10...+10 Regulation of the front air percentage
STANDBY OFF  ON
Activation or deactivation of the stand-by function
KEYS LOCKED OFF  ON Activation or deactivation of the keys locked
function
*V2  AIR 10...+10 Regulation of the ducted air percentage
RESET OFF  ON Indicates the values that can be modied by the
user asby default
USER MENU
GO BACK  SAVE  EXIT
BROWSE PARAMETERS: NEXT P2 ; PREVIOUS P3
MODIFY SETTING DATA: INCREASE P4; DECREASE P5
CONFIRM  ACCESS MENU

P1
P2 P3
P4 P5
P6
P1 P4
P3
P2
P5
P6
P6
7
MENU FUNCTION
GENERAL DATA Allows setting a series of general parameters.
Refer to the corresponding data table.
FACTORY SETTINGS Allows conguring a series of factory parameters.
Refer to the corresponding data table.
INSTALLER
Allows conguring a series of factory settings.
The possible settings refer to pellet feed,
ue motor and ow all in %.
DUCTED DATA Voltage setting of the second
motor depending on the various work phases.
CONTROLS ACTIVE Allows activating or deactivating a series of settings, such as
fumes motor encoder, debimeter, ign-plug, serial.
CHIMNEY TYPE Key“77" allows setting the
intake ow for the various debimeter operating phases.
OUTPUTS TEST
Allows testing the board outputs: Flue motor and exchanger fans; the voltage can also
be set. As for the auger, the test activation time can be set. As for the ign-plug, it can be
turned on and o.
COUNTERS
MEMORIES
Displays in sequence the consumption hours for the various brands
(auger operating hours), overall operating hours
partial hours, number of start-ups and the last 5 alarms occurred.
DEFAULT Key“O1”(letter "o") allows reloading factory settings.
RESET PART HOURS Key“77” allows resetting partial operating hours.
RELEASE Key“77” allows skipping all verications for 60 seconds and restarting the stove even
with high ue gas temperature, unreset timers, etc.
ATTIVAZIONE Automatic setting (day - month - year)
STRUCTURE OF THE TECHNICIAN MENU
TECHNIC SET
CODE A0
TECHNICIAN MENU
GO BACK  SAVE  EXIT
BROWSE PARAMETERS: NEXT P2 ; PREVIOUS P3
MODIFY SETTING DATA: INCREASE P4; DECREASE P5
CONFIRM  ACCESS MENU
THE DATA IN TABLES ON THE FOLLOWING PAGES ARE FOR ILLUSTRATION PURPOSES ONLY!

P6
P6
P2
8
TECHNICIAN MENU
GENERAL DATA
FIRMWARE VXX
PG00 60
PG01 0,6
PG02 0,6
PG03 P1 0,6
PG04 P5 1,6
PG05 ON 1680
PG06 1860
PG07 P1 1380
PG08 P5 1920
PG09 180
PG10 200
PG11 200
PG12 65
PG13 125
PG14 DELTA T OFF 2
PG15 DELTA T ON 2
FACTORY SETTINGS
FIRMWARE VXX
PF00 10
PF01 15
PF02 05
PF03 ON 110
PF04 280
PF05 OFF
PF06 55
PF07 85
PF08 40
PF09 30
PF10 1
PF11 31
PF12 1920
PF13 0,6
PF14 1
PF15 1920
PF16 1920
PF17 1920
PF18 220
PF19 00
PF20 1680
GENERAL DATA
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Enter pressing P6
To modify a single parameter, press P4 or P5, to
continue and memorise press P2, to retrocede in the various
parameters press P3.
Press P6 to conrm and P1 to return to the previous menus up to the initial
status.
FACTORY SETTINGS
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until FACTORY SETTINGS is displayed.
Enter pressing P6
To modify a single parameter, press P4 or P5, to
continue and memorise press P2, to retrocede in the various
parameters press P3.
Press P6 to conrm and P1 to return to the previous menus up to the initial
status.
GENERAL DATA
TECHNIC SET
CODE A0
TECHNIC SET
CODE A0 GENERAL DATA
FACTORY
PARAMETERS
THE DATA IN THE TABLES ARE FOR ILLUSTRATION PURPOSES ONLY

P6
P2
P6
P2
9
INSTALLER
FIRMWARE VXX
PI00 P15 +/- 30%
PI01 P15 +/- 30%
PI02 0
DUCTED DATA
FIRMWARE VXX
PC00 P1 170
PC01 P5 190
PC02 OFF 180
PC03 ALARM 220
TECHNICIAN MENU
INSTALLER
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until INSTALLER is displayed.
Enter pressing P6
To modify a single parameter, press P4 or P5, to
continue and memorise press P2, to retrocede in the various
parameters press P3.
Press P6 to conrm and P1 to return to the previous menus up to the initial
status.
DUCTED DATA
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until DUCTED DATA is displayed.
Enter pressing P6
To modify a single parameter, press P4 or P5, to
continue and memorise press P2, to retrocede in the various
parameters press P3.
Press P6 to conrm and P1 to return to the previous menus up to the initial
status.
GENERAL DATA
TECHNIC SET
CODE A0
INSTALLER
GENERAL DATA
TECHNIC SET
CODE A0
DUCTED DATA
THE DATA IN THE TABLES ARE FOR ILLUSTRATION PURPOSES ONLY

P6
P2
P6
P2
10
CONTROLS ACTIVE
FIRMWARE VXX
PE00 ENCODER ON
PE01 ON
PE02 ON
PE03 SERIAL ON
CHIMNEY TYPE
FIRMWARE VXX
PA00 on
PA01 000
PA02 0,5
PA03 0,1
PA04 0,8
TECHNICIAN MENU
CONTROLS ACTIVE
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until CONTROLS ACTIVE is displayed.
Enter pressing P6
Use the P4 or P5 keys to activate - deactivate, P2 to select another
component and P3 to go back.
Press P6 to conrm and P1 to return to the previous menus up to the
initial status.
CHIMNEY TYPE
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until CHIMNEY TYPE is displayed.
Enter pressing P6
Hold key P4 down to reach code "77" and conrm with P6.
To modify a single parameter, press P4 or P5, to
continue and memorise press P2, to retrocede in the various
parameters press P3.
Press P6 to conrm and P1 to return to the previous menus up to the
initial status.
GENERAL DATA
TECHNIC SET
CODE A0
CONTROLS ACTIVE
GENERAL DATA
TECHNIC SET
CODE A0
CHIMNEY TYPE
THE DATA IN THE TABLES ARE FOR ILLUSTRATION PURPOSES ONLY

P6
P6
P2
P6
P2
11
FIRMWARE VXX
Ignition plug test ON/ OFF
Auger test 0.000 ... 4.000
Fumes test 0.00F ON/ OFF
Fan 1 test OFF..65V....225V
Fan 2 test OFF..65V....225V
TECHNICIAN MENU
ALARM MEMORY RESET
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until ALARM MEMORY RESET is displayed.
Enter pressing P6
Hold key P4 down to reach code "77" and conrm with P6.
"DONE" will be signalled on the display to conrm the command
OUTPUTS TEST
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until OUTPUTS TEST is displayed.
Enter pressing P6
Use the P4 or P5 keys to activate - deactivate the various tests, P2 to select
another component and P3 to go back.
Press P1 to return to the previous menus up to the initial status.
GENERAL DATA
TECHNIC SET
CODE A0
ALARM MEMORY
RESET
GENERAL DATA
TECHNIC SET
CODE A0
INSTALLER
PARAMETERS
OUTPUTS TEST
THE DATA IN THE TABLES ARE FOR ILLUSTRATION PURPOSES ONLY
FROM V3 FIRMWARE NO LONGER AVAILABLE

P6
P2
P6
P2
12
PARAMETER
VALUE
Hours p1
Hours p2
Hours p3
Hours p4
Hours p5
Total hours
Part hours
Ignition
mem 1 alarms
ALARM
mem 2 alarms
mem 3 alarms
mem 4 alarms
mem 5 alarms
TECHNICIAN MENU
COUNTERS MEMORIES
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until COUNTERS MEMORIES is displayed.
Enter pressing P6
Use P2 to browse through the readout and P3 to go back.
Press P1 to return to the previous menus up to the initial status.
DEFAULT
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until DEFAULT is displayed.
Enter pressing P6
Hold key P4 down to reach code "o1" and conrm with P6.
"LOADED DATA" will be signalled on the display to conrm the command
GENERAL DATA
TECHNIC SET
CODE A0
COUNTERS
MEMORIES
GENERAL DATA
TECHNIC SET
CODE A0
DEFAULT
NOTE: ALL CHANGES WILL BE RESET. ONLY THE COUNTERS MEMORIES WILL REMAIN UNCHANGED

P6
P2
P6
P2
13
TECHNICIAN MENU
RESET PART HOURS
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until RESET PART HOURS is displayed.
Enter pressing P6
Hold key P4 down to reach code "77" and conrm with P6.
"DONE" will be signalled on the display to conrm the command
UNLOCK
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until UNLOCK is displayed.
Enter pressing P6
Hold key P4 down to reach code "77" and conrm with P6. Hold key P1
down until the alarm signal disappears.
GENERAL DATA
TECHNIC SET
CODE A0
RESET PART HOURS
GENERAL DATA
TECHNIC SET
CODE A0
UNLOCK

P1P2
P3
P6 P4
P5
14
STOVE STATUS
It is possible to know the status of the stove at any time.
Press key 3 along with key 5.
The values will appear in order that concern the following variables:
MEANINGS:
Status 0 = Temperature of the fumes measured by the probe.
Status 1 = Auger time with reference to the programming
Status 2 = Fumes motor speed measured by the encoder
Status 3 = Status change timer
Status 4 = Temperature measured by the tank probe (where present)
Status 5 = Flow with reference to the debimeter mounted in the primary air inlet
Status 6 = Actual power of the stove (1-16)
Status 7 = Inlet air temperature measured by the debimeter
Status 8 = Mechanical Pressostat - normal working indicates "ON" - Problem occuring
Indicates "OFF"
Status 9 = Auger's errors number (where present)
Status A= Type of Modulation:
"0" No modulation, "1" room temperature,
"2" additional thermostat, "3" ue gas temperature,
"4" tank temperature, "5" motherboard temperature
STATUS
Status 0 = Flue gas temperature
Status 1 = Auger time
Status 2 = Fumes motor speed
Status 3 = Status change timer
Status 4 = Tank temperature
Status 5 = Flow
Status 6 = Actual power
Status 7 = Inlet air temperature
Status 8 = Mechanical Pressostat
Status 9 = Auger's errors number (where present)
Status A= Type of Modulation
VARIOUS CONTROLS
LOAD
This function allows to activate the pellet feeding motor reducer for continuous functioning: this allows
lling the pellet feeding spiral when it is empty to prevent ignition failures.
Controls procedure:
From the“o” status, press buttons 2 and 5 simultaneously until“LOAD” appears on display D1.
To interrupt the following procedure remove and re-apply current
FLOW RATE CONTROL
This procedure allows verifying the actual stove consumption at the various speeds. Through this function pellets are automatically fed for
60 minutes at the selected speed.
To activate this function, place yourself at one of the pellet feeding speeds while the stove is cold (o)
(General parameter programming PG03=power 1 - PG04=power 5)
Once selected, the stove will automatically activate the test after approximately 1 minute.
Once the time has elapsed, the stove will return to OFF status.
To nish the test earlier, exit by pressing P1.
ATTENTION:
TO VERIFY THE FLOW RATE, THE MACHINE MUST BE COLD AND OFF!
ATTENTION:
TO FUN THE "LOAD" FUNCTION, THE MACHINE MUST BE OFF!
ATTIVAZIONE
CONTROLS PROCEDURE
Press P6 and SET CLOCK will appear.
Press P2 several times until TECHNIC SET is displayed.
Press P6.
Hold key P4 down to reach the reserved code "A0"
When the code has been reached, conrm by pressing P6
"GENERAL DATA" will appear
Press P2 until ATTIVAZIONE is displayed.
Enter pressing P6
Use P2 to browse through the readout and P3 to go back.
Press P1 to return to the previous menus up to the initial status.

15
ALARMS
DISPLAY EXPLANATION SOLUTION
Indicates the presence of an alarm.
On: indicates the presence of an alarm
O: indicates the absence of alarms
Flashing: indicates the deactivation of the depression sensor.
The alarm can be reset by pressing key 1 for 3 seconds only if the
fumes motor has stopped and if 15 minutes have passed from
displaying the same alarm.
FUMES FAILURE Fault correlated to the ue gas
exhaust motor.
Check that the fumes motor turns freely.
Control fumes motor and encoder wiring.
Perform the outputs test to check that the encoder/fumes motor
functions.
Replace the fumes motor.
FUMES PROBE Fault correlated to the fumes probe.
Perform the stove status (status 0) and check whether the
value detected by the probe is read.
Check the wiring.
Replace the fumes probe
ALARM FUMES
OVERTEMPERATURE
The ue gas temperature has
exceeded 310°C
Check pellet ow (see“Pellet feed adjustment”).
Check that the machine is clean, including the ue route.
Do not rest cloths on the machine.
CLEAN
CHECKUP 1  2
1= AT STARTUP
2= AT WORK
The combustion chamber or burn pot
bottom are dirty.
The door is not closed correctly.
The ash drawer is not closed
correctly.
The depression sensor is faulty.
The ue exhaust pipe is blocked.
Incorrect installation
Make sure the holes at the burn pot bottom are completely free.
Check cleanliness of the fumes pipe and the combustion chamber.
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Other restoration operations must be carried out by an authorised
technician.
DEPR ALARM The mechanical depression sensor
has tripped
Check closure of the door
Check the status of the tube to the silicon sensor
Check cleanliness of the flue
Check the amount of pellets in the feed box
NO
IGNITION
The pellet feed-box is empty.
Pellet feed calibration inadequate.
Incorrect installation
Check for the presence of pellets in the feed-box.
Adjust pellet ow (see“Pellet feed adjustment”).
Check the procedures described in the“Ignition”chapter.
BLACKOUT NO IGN. No current during the ignition phase.
Check for the presence of pellets in the feed-box.
Regulate the pellet flow.
Check that the machine is clean.
Check that the ign-plug is positioned correctly.
Replace the ign-plug.
Check that there is not too much draught, if this is not the case, lower the
fumes motor in ignition parameter.
NO PELLETS
In the work phase, the t° of the ue
gases has dropped below factory
parameters
Check for the presence of pellets in the feed-box.
Regulate the pellet ow.
COOLING STANDBY Attempt to release the alarm with
stove still in cooling mode.
Every time the stove displays one of the alarms listed above it will
switch-o automatically.
The stove will block any release attempt during this phase,
showing the alarm itself and ATTE alternately on the display.
The alarm can be reset by pressing key 1 for 3 seconds only if the
fumes motor has stopped and if 15 minutes have passed from
displaying the same alarm.
DEPR SENSOR
DAMAGE Component disconnected or faulty
Check whether the sensor is disconnected
Check whether the sensor is faulty and replace it if necessary
ALLARME COMANDO
COCLEA
Anomalous functioning
of pellet feeding Verify the output of the motherboard
BLOCCO COCLEA abnormal function
motor pellet
Check if the pellet motor turns freely
Check pellet motor wiring and its encoder wiring
Replace the pellet motor

16
DISPLAYS
DISPLAY REASON
OFF Stove o
START The start phase is in progress
PELLET FEEDING The feeding of the pellet during the ignition phase is in progress
IGNITION The ignition phase is in progress
STARTUP The start phase is in progress
WORK The normal work phase is in progress
MODULATION The stove is modulating
BURN POT CLEANING The automatic burn pot cleaning is in progress.
FINAL CLEANING When the stove is switched-o, nal cleaning is in progress. The nal cleaning phase lasts about 10
minutes.
STAND BY Stove o due to temperature reached and in stand-by for re-ignition.
STAND BY EXT Stove o due to an external thermostat, waiting for re-ignition
COOLING STANDBY
A new ignition is attempted when the stove has just been switched-o
When the stove switches o, it is necessary to wait until complete fumes motor switch o and then clean
the burn pot.
The stove can only be re-ignited when these operations have been performed.
COOLING STDBY
BLACK OUT The stove is cooling due to black out
LOW
Room thermostat set at minimum value.
In this way the stove only works at 1st power independently from the power set. To escape this function
just raise the room temperature using button 4 and then key 2.
HOT
Set room thermostat set at maximum value.
The stove works at set start, without ever modulating. To escape this function just lower the set
temperature using key 4 and then key 1.

17
A SMALL PHOTOGRAPHIC KEY, ACCOMPANIED BY A BRIEF DESCRIPTION, HAS BEEN REALISED TO EASE RECOGNITION OFTHE ELECTRIC COMPONENTS.
ATTENTION!!! THE COMPANY RESERVES THE RIGHT TO REPLACE COMPONENTS WITH OTHERS HAVING EQUAL OR IMPROVED
FEATURES WITHOUT PRIOR NOTICE!
WE RECOMMEND REFERRING TO THE EXPLODED VIEWS AVAILABLE AT OUR WEBSITE FOR SPARE PART REQUESTS!!!
DISPLAY
The displays allow to make adjustments to the product, control the correct functioning by displayed messages.
Models:
CIRCUIT BOARD
The circuit board manages the various inputs/outputs necessary for functioning of the product.
ADDITIONAL BOARDS
Some products require particular additional boards for their
functioning.
COMPONENTS

18
DUCTING FAN
Some products have a fan available for ducting the hot air.
Models:
FLUE GAS EXPULSION MOTOR
The ue gas expulsion motor generates depression inside the combustion chamber in order to obtain optimum product combustion.
PELLET FEED MOTOR REDUCER
This motor allows automatic pellet feeding inside the burner.
Models:
Motor reducer with 2 rpm.
Motor reducer with 2 rpm. ( only for circuit board 2272599)
Motor reducer with 4.75 rpm.
TANGENTIAL FAN
The tangential fan is the device that allows to create forced ventilation inside the room.
A SMALL PHOTOGRAPHIC KEY, ACCOMPANIED BY A BRIEF DESCRIPTION, HAS BEEN REALISED TO EASE RECOGNITION OFTHE ELECTRIC COMPONENTS.
ATTENTION!!! THE COMPANY RESERVES THE RIGHT TO REPLACE COMPONENTS WITH OTHERS HAVING EQUAL OR IMPROVED
FEATURES WITHOUT PRIOR NOTICE!
WE RECOMMEND REFERRING TO THE EXPLODED VIEWS AVAILABLE AT OUR WEBSITE FOR SPARE PART REQUESTS!!!
COMPONENTS

19
DAMPERS
A SMALL PHOTOGRAPHIC KEY, ACCOMPANIED BY A BRIEF DESCRIPTION, HAS BEEN REALISED TO EASE RECOGNITION OFTHE ELECTRIC COMPONENTS.
ATTENTION!!! THE COMPANY RESERVES THE RIGHT TO REPLACE COMPONENTS WITH OTHERS HAVING EQUAL OR IMPROVED
FEATURES WITHOUT PRIOR NOTICE!
WE RECOMMEND REFERRING TO THE EXPLODED VIEWS AVAILABLE AT OUR WEBSITE FOR SPARE PART REQUESTS!!!
REMOTE CONTROL
Allows to communicate with the appliance circuit board, sending commands to be followed.
There are 5 types of remote control:
COMPONENTS

20
ULTRAWATT CARTRIDGE
The ign-plug is just a heating resistor: once powered, it can develop a temperature that allows
to cause a ame.
DEPRESSION CONTROL CIRCUIT BOARD
This sensor develops the depression inside the appliance. Any anomaly will be signalled on the
display.
DEBIMETER
This sensor develops the depression inside the appliance. Any anomaly will be signalled on the
display.
BULB THERMOSTAT
The bulb thermostat is a mechanical safety device for temperature that acts as a switch: if
the temperature is lower than the value at which the thermostat is calibrated, the contact
remains closed allowing passage of the current. If the temperature exceeds the value set in the
thermostat, the contact opens and must be restored manually after having analysed the cause
of the event.
There are two types of thermostat:
set at 85°C
set at 100°C: it intervenes whenever the temperature of the tank rises excessively.
TEMPERATURE PROBE
The temperature sensor is available in dierent lengths in relation to use.
MECHANICAL PRESSURE SWITCH
the pressure switch is a mechanical safety device that controls the depression
AIR PRESSURE SWITCH
the digital pressure switch controls the depression
MICRO SWITCH
The micro switch is a device that is used in some products as a safety device or as a limit switch
indicator.
A SMALL PHOTOGRAPHIC KEY, ACCOMPANIED BY A BRIEF DESCRIPTION, HAS BEEN REALISED TO EASE RECOGNITION OFTHE ELECTRIC COMPONENTS.
ATTENTION!!! THE COMPANY RESERVES THE RIGHT TO REPLACE COMPONENTS WITH OTHERS HAVING EQUAL OR IMPROVED
FEATURES WITHOUT PRIOR NOTICE!
WE RECOMMEND REFERRING TO THE EXPLODED VIEWS AVAILABLE AT OUR WEBSITE FOR SPARE PART REQUESTS!!!
COMPONENTS