Extron electronics XPA U 3502 User manual

XPA U 3502 • Setup Guide
The Extron XPA U 3502 is a 2-channel audio power amplifier for use in low-impedance speaker systems.
The XPA U 3502 is 1U high, half rack width, and rack mountable. The amplifier has mounting holes for 9” and deeper rack shelves, and
is plenum-rated with an optional flex conduit adaptor. The unit is convection cooled.
This guide provides instructions for an experienced installer to set up and operate the XPA U 3502 power amplifier. For full installation,
configuration, and operation details, see the XPA U 3502 User Guide available at www.extron.com.
Installation Steps
Step 1 — Mounting
Turn off all of the equipment and disconnect it from the power source. Mount the amplifier as required; the unit can be securely
mounted in a variety of locations using optional Extron Mounting Brackets and accessories (see the Extron website for compatible
optional mounting accessories) or using the included 3-piece bracket system. The brackets do not come attached to the amplifier.
Below are two methods of rack mounting the amplifiers.
Rack Ear Mounting (Single Unit)
The XPA U 3502 ships with a set of rack ears, allowing the amplifier to be installed in a full rack-width space. Mount the amplifier with
rack ears as follows:
1. If the amplifier has its flat bottom rubber feet installed, remove them.
2. Attach the rack ears to the sides with the four provided #6 machine screws (1).
3. Insert the amplifier into the rack and align the holes in the rack ears with the holes on the rack.
4. Secure the amplifier to the rack using the four provided 10-32 x 3/4” screws (2).
e
XPAU 3502
POWERAMPLIFIERS
12
OVER
TEMP LIMITER/PROTECT
SIGNAL
12
e
XPAU 3502
POWERAMPLIFIERS
12
OVER
TEMP LIMITER/PROTECT
SIGNAL
Figure 1. XPA U 3502 Rack Ear Mounting
Bridge Plate Rack Mounting (Side-by-Side)
The XPA U 3502 ships with a bridge plate connector to connect two amplifiers together and form a full rack-width unit. Mount and
connect two amplifiers as follows:
1. If the amplifier has its flat bottom rubber feet installed, remove them.
2. Position two amplifiers upside down and next to each other as shown below.
3. Use the bridge plate connector and the four provided #4 machine screws to connect the two units together (1).
4. Attach the two short rack ears to the units with the four provided #6 machine screws (2).
5. Insert the amplifier into the rack and align the holes in the rack ears with the holes on the rack.
6. Secure the amplifier to the rack using the four provided 10-32 x 3/4” screws (3).
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
1

e
XPA U 3502
POWERAMPLIFIERS
12
OVER
TEMP LIMITER/PROTECT
SIGNAL
e
e
XPA U 3502
POWERAMPLIFIERS
12
OVER
TEMP LIMITER/PROTECT
SIGNAL
Mounting
screws (4)
2
1
3
e
XPAU 3502
POWERAMPLIFIERS
1 2
OVER
TEMP LIMITER/PROTECT
SIGNAL
02
RS
e
XPAU 3502
POWERAMPLIFIERS
1 2
OVER
TEMP LIMITER/PROTECT
SIGNAL
Figure 2. XPA U 3502 Bridge Plate Rack Mounting
Ventilation Recommendation
Excessive heat can decrease a power amplifier’s lifetime. An
Over Temp LED indicator on the front panel lights red when the
maximum recommended operating temperature of +122 °F (+50
°C) has been surpassed.
To minimize the chances of overheating, the amplifier should
be arranged in a rack so that the evironment does not reach
or surpass +122 °F (+50 °C). See the image to the right for the
optimal way to arrange the XPA U 3502. No more than four stacks
of amplifiers in a one-on-top-of-the-other arrangement should
occur without an open between the stacks.
The XPA U 3502 can also be arranged directly above or below a
non-XPA Ultra device, but in any case, the environment should still
not reach or exceed +122 °F (+50 °C).
Vent Space
Vent Space
Vent Space
Vent Space
Vent Space
Vent Space
Vent Space
XPA U 3502 • Setup Guide (Continued)
2

Set Amplifier Output Mode
Step 2 — Rear Panel Configuration
Follow the instructions below to learn how to configure the rear panel for the XPA U 3502.
• Wire the source output to the Line Input 3.5mm captive screw port as shown below. Figure 3 shows both balanced and
unbalanced inputs.
ATTENTIONS:
• Do not tie channel output pins to each other or to ground. Doing so will short out the outputs, damage the amplifier, or
both.
• Ne pas lier les sorties 1 et 2 des canaux entre elles ou à la terre. Les sorties pourraient être court-circuitées et/ou
l’amplificateur pourrait être endommagé.
• To avoid risk of damage to the amplifier or the speakers, only connect low-impedance speaker loads (8Ω/4Ω) to the
appropriately marked output connectors on the amplifier.
• Pour éviter tout risque de détérioration de l’amplificateur ou des enceintes, connectez toujours les charges de l’enceinte
faible impédance (8Ω/4Ω) aux connecteurs de sortie correctement identifiés sur l’amplificateur.
NOTE: You must use Class 2 wiring for the amplified outputs to comply with UL requirements.
"(5 mm) MAX.
3
16
Do not tin
the wires!
100-240V 1.5A, 50-60 Hz
20
2
4
6
8
10
14
18
26
∞
12
10
2
4
6
8
10
14
18
26
∞
12 1
2
G
GC
V
GCV
STANDBY
SIGNAL
1
SIGNAL
LIMITER/
PROTECT
LIMITER/
PROTECT
2
ATTENUATION INPUTSREMOTE
XPA U 3502
2
1
CLASS 2 WIRING
OUTPUTS
8Ω/4Ω
1
2
CH 2
Ster
eo 8Ω or 4Ω
Speaker Loads
Wire output connector
to speaker loads as
shown below
Wire CH 1 and CH 2
input connector based
on source as shown below
Use both CH 1 and CH 2
Attenuators (set
levels independently)
CH 1
Figure 3. XPA 3502 Output Configuration
Step 3 — Remote Ports
STANDBY
1
GV C
GV C
G
2
REMOTE
Figure 4. Remote Volume Control and Standby Ports
The 3.5 mm 5-pin captive screw remote control ports (shown above) are used to control volume on channel 1 on pins 1, 2, and 3,
and standby mode through contact closure on the pins 4 and 5. The upper, 3-pin captive screw remote control port is used to control
volume on channel 2.
The volume control ports can be wired to Extron remote volume controllers such as an Extron VCM 200 series and MLC 64 RS VC D
controllers, or Extron Control products with the digital Remote Volume Control Port, such as the MLC 100 Plus and IPCP Pro 255. For
more details on wiring the volume control ports see the XPA U 3502 User Guide.
XPA U 3502 • Setup Guide (Continued)
3

XPA U 3502 • Setup Guide (Continued)
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
When the STANDBY pin (pin 5) is shorted to ground (Pin 4), the amplifier goes into standby mode. Standby mode turns off all the
outputs, although the amplifier still receives power. The power LED on the front panel lights amber when the amplifier is in Standby
mode.
NOTE: A 10k ohm resistor is included with the amplifier. If the resistor is connected between the STANDBY and Ground
pin, the auto-standby timer is suppressed. The STANDBY pin can still be shorted to the Ground pin to put the amplifier in
standby.
Step 4 — Powering on Equipment
ATTENTION:
• The amplifier must be powered on last.
• L’amplificateur doit être mis sous tension en dernier.
Reconnect all the power cables and switch on all of the other equipment before attaching the IEC power cable and powering on the
unit. The power LED will light green.
Step 5 — Adjusting Attenuation
NOTE: Set the volume control on the connected control device(s) to maximum and ensure that the amplifier
is not currently forced into standby mode via the standby pin prior to making adjustments.
Adjust audio attenuation using the rear panel adjustment attenuators as seen to the right.
See Rear Panel Features in the XPA U 3502 User Guide for more information.
ATTENTION:
• The default position of all potentiometers when shipped is turned fully counter-clockwise (fully attenuated).
• La position par défaut de tous les potentiomètres lors de leur expédition est orientée vers le sens antihoraire (atténuation
complète).
• Do not use a screwdriver to adjust the potentiometers. The potentiometers should only be adjusted as needed using the
included tweeker (small screwdriver).
• Ne pas utiliser de tournevis pour ajuster les potentiomètres. Les potentiomètres doivent uniquement être ajustés selon les
besoins avec le petit tournevis fourni.
• While potentiometer tuning knobs may look like screws, they do not function in the same manner. Use a light touch when
adjusting to avoid applying excessive torque to the potentiometers.
• Bien que les boutons de réglage du potentiomètre ressemblent à des vis, ils n’ont pas la même fonction. Exercez une
pression légère lors du réglage afin d’éviter un serrage excessif des potentiomètres.
• Applying excessive torque can mechanically damage the potentiometer, rendering it inoperable and voiding the product
warranty.
• Un serrage excessif peut endommager le potentiomètre, le rendant inutilisable et annulant la garantie du produit.
Step 6 — Checking LEDs
Check the Limiter/Protect and Signal LEDs on the front and rear panels to see if any problems are encountered (see Front Panel
Features and Troubleshooting in the XPA U 3502 User Guide for more information).
0
1
12
4
6
8
10
12
18
14
26
∞
0
2
12
4
6
8
10
12
18
14
26
∞
ATTENUATION
68-3545-50 Rev. A
04 21