Extron electronics DVI DA2 User manual

IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
DVI DA2 and DVI DA4 • Setup Guide
These instructions provide a quick setup guide for the Extron DVI DA2 and DVI DA4. Installation
and service must be performed by authorized personnel only. To install, cable, and power on
the DVI DA2 and DVIDA4, do the following.
Step 1 — Mounting
Install the DVI DA2 or DVI DA4 on a desk, or mount it under a desk or in a rack.
Step 2 — DVI Input/Output Cable Connections
Connect these cables, but do not power on the equipment yet:
• Connect a DVI cable from the Input connector to the video source device.
• Connect a DVI cable from the Local Monitor connector to the desired local output device.
• Connect DVI cables from the output connectors to the desired display devices.
12V
0.4A MAX
POWER
DVI-D INPUT DVI-D OUTPUT
LOCAL MONITOR
1 2
DVI DA2
Ext
ron
DV
I DA2
DV
I Distribution
Am
plier
PC
Local Monitor
Flat Panel
Display
Step 3 — Power Cable Connections
Connect the 12 VDC power supply to the power receptacle of the unit.
DC Power
Input
POWER
12V
0.4A MA
X
Power Supply
Output Cord
SECTION A–
A
RidgesSmooth
AA
DC Power Cord
Captive Screw Connector
Ground
+12 VDC input
G
External Power Supply
(12 VDC, 0.5 A max.)
Ground all
Devices

DVI DA2 and DVI DA4 • Setup Guide (Continued)
© 2009-2018 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility,
accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on
the Extron website.
68-1376-50 Rev. D
10 18
ATTENTION:
•If not provided with a power supply, this product is intended to be supplied by a UL Listed
power source marked “Class 2” or “LPS” and rated output 12VDC, 1.5 A minimum. Always
use a power supply provided by or specified by Extron. Use of an unauthorized power
supply voids all regulatory compliance certification and may cause damage to the supply
and the end product.
•Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une
source d’alimentation certifiée UL de classe 2 ou LPS, avec une tension nominale 12 Vcc,
1,5 A minimum. Utilisez toujours une source d’alimentation fournie ou recommandée par
Extron. L’utilisation d’une source d’alimentation non autorisée annule toute certification de
conformité réglementaire, et peut endommager la source d’alimentation et l’unité.
•Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity as the
Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the
equipment rack within the dedicated closet, podium, or desk.
•Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les
espaces d’aération ou dans les cavités murales. La source d’alimentation doit être placée
à proximité de l’équipement Extron dans un emplacement ordinaire soumis à un degré de
pollution de catégorie II, solidement xé au rack d’équipement d’une baie technique, d’un
pupitre, ou d’un bureau.
•The installation must always be in accordance with the applicable provisions of National
Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section
16. The power supply shall not be permanently xed to building structure or similar structure.
•Cette installation doit toujours être conforme aux dispositions applicables du Code américain
de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de
l’électricité, partie 1, section 16. La source d’alimentation ne devra pas être xée de façon
permanente à la structure de bâtiment ou à d’autres structures similaires.
NOTES: The length of the exposed wires in the stripping process is critical. The ideal length is
3/16inches (5 mm). If the exposed section is longer, the exposed wires may touch, causing
a short circuit between them. If it is shorter, the wires can be easily pulled out even if tightly
fastened by the captive screws.
Do not tin the wires. Tinned wire does not hold its shape and can become loose over time.
Step 4 — Applying Power
NOTE: Output 1 is used as DDC reference and Hotplug Detect and a local monitor must be
connected to it before the source device is powered on. Since Output 1 is used for reference,
all displays connected to the other outputs must be capable of handling resolutions greater
than or equal to that of Output 1.
•Power on the local monitor. •Power on the source input device.
•Power on the display devices.