Extron electronics DTP CrossPoint 84 User manual

68-2349-50 Rev. F
06 22
DTP CrossPoint 84
Scaling Presentation Matrix Switchers with DTP Extension
Matrix Switchers
IMPORTANT:
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
IMPORTANT:
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
Setup Guide

Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron website,
www.extron.com.
www.extron.com
I


Copyright
© 2014-2022 Extron. All rights reserved. www.extron.com
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (®), registered service marks (SM), and trademarks (TM) are the property of RGBSystems, Inc. or Extron (see the
current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks (®)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, GlobalConfigurator,
GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,
NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,
SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks (™)
AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), AVEdge, CableCover, CDRS(ClassD Ripple Suppression),
CodecConnect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital
Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,
PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, SIS, SimpleInstructionSet, Skew-Free,
SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION:
• The Twisted Pair Extension technology works with unshielded twisted pair (UTP)
or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are required.
• La technologie extension paires torsadées fonctionne avec les câbles paires
torsadées blindées(UTP) ou non blindées(STP). Afin de s’assurer de la
compatibilité entre FCC ClasseA et CE, les câbles STP et les connecteurs STP
sont nécessaires.
NOTES:
• This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensure compliance with FCC emissions limits.
• For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.

Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&*X2)*X2#*X2! CE}
NOTE: For commands and examples of computer or device responses used in this
guide, the character “0” is the number zero and “O” is the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at https://www.extron.com/technology/glossary.aspx.

Contents Contents
Introduction ............................................... 1
About this Guide.................................................. 1
About the DTP CrossPoint Matrix Switchers........ 1
DTP Input and Output Signals ......................... 3
Installation................................................. 4
Rear Panel........................................................... 4
Video Inputs and Outputs ................................ 5
Audio Inputs and Outputs................................ 6
Serial and IR Insertion Connections ................. 7
Control Connections........................................ 7
Switcher Reset ................................................ 7
Power.............................................................. 7
Additional Connector Information..................... 8
Front Panel........................................................ 12
Front Panel Operations............................ 13
Creating a Tie .................................................... 13
Recalling a Preset.............................................. 14
Viewing Ties (and Muting Outputs)..................... 14
Viewing and Adjusting Volume and Mic
Volume ............................................................. 14
Setting the Front Panel Locks (Executive
Modes)............................................................. 14
Selecting Lock Mode 2 or Toggling
Between Mode 2 and Mode 0 ...................... 15
Selecting Lock Mode 2 or Toggling
Between Mode 2 and Mode 1 ...................... 15
Remote Control........................................ 16
Selected SIS Commands................................... 16
Establishing a Network (Ethernet)
Connection................................................... 16
Number of Connections................................. 17
Establishing a USB Port Connection.............. 17
Host-to-Switcher Instructions ........................ 17
Common SIS Command Symbols ................. 17
SIS Command and Response Table for
Matrix Switcher Commands ............................. 18
Installing and Starting the Control Programs ...... 20
Installing the Programs .................................. 20
Starting the Product Configuration
Software....................................................... 21
Starting the DSP Configurator Program ......... 22
Accessing the HTML Pages............................... 24
viiTechnical Publications Standards and Styles • Contents

Technical Publications Standards and Styles • Contents viii

DTP CrossPoint 84 • Introduction 1
Introduction
This section gives an overview of the Extron DTP CrossPoint 84 Series matrix switchers and
describes their features. Topics that are covered include:
• About this Guide
• About the DTP CrossPoint Matrix Switchers
About this Guide
NOTE: For more information on subjects in this guide, see the DTP CrossPoint 84
Series User Guide and the IPCP Pro Series User Guide available at www.extron.
com.
This guide provides instructions for an experienced installer to set up
and operate the Extron DTP CrossPoint 84 Scaling Presentation Matrix
Switchers with DTP Extension. Step by step instructions show you how to:
• Connect the hardware (see Installation on page4)
• Perform basic operations (see Front Panel Operations on page13)
• Use both the front panel controls and selected Simple Instruction Set (SIS) commands
(see Front Panel Operations on page13 and SIS Command and Response
Table for Matrix Switcher Commands on page18)
• Load and start up the Microsoft®Windows®-based Product Configuration Software (see
page21) and DSP Configurator Program (see page22).
• Connect to the built-in HTML pages (see page24),which you can use to view the switcher status
and make changes to the communications protocol and set the system clock.
About the DTP CrossPoint Matrix Switchers
The DTP CrossPoint matrix switchers distribute HDCP-compliant HDMI and Extron
proprietary DTP video and audio signal types. A matrix switcher routes any input signal
to any combination of outputs. It can route multiple input and output configurations
simultaneously.
The fixed matrix size switchers support a total of eight inputs: six HDMI and two inputs from
Extron DTP transmitting devices. The matrix switchers provide four outputs: two HDMI and
two scaled DTP outputs.
The DTP CrossPoint Matrix Series consists of three 8-input by 4-output models,
differentiated by their audio and control capabilities:
• DTP CrossPoint 84
• DTP CrossPoint 84 IPCP SA — Includes a stereo audio amplifier and a built-in Extron
IPCP Pro 350 control processor
• DTP CrossPoint 84 IPCP MA 70 — Includes a 70 V mono audio amplifier and a built-
in Extron IPCP Pro 350 control processor

DTP CrossPoint 84 • Introduction 2
POWER
12V
2
--AMAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, Y, R-Y, B-YHDMIHDMI
SIG LINK
DTP OUT
AUDIO
CONTACTRS-232TALLY
3
123G123+V
RESET
INPUTS
OVER DTPREMOTE
100-240V ~ --A MAX
50/60 Hz LAN
EXP
RS-232
Tx Rx G
RESET
MIC +48V
5678
1234 8
4 1
12345G 678910 G
11 12 13 14 15 G1617181920G
234
56 78
910
11 127
3
6
2
5
1
MIC/LINE INPUTS
OUTPUTS
DIGITAL I/O
REMOTE
DMP 128 C
LAN
3
21
4
321
50-60 Hz
100-240V ~ 2.0 A MAX
1
LR
SIG LINK
OUT
SIG LINK
OUT
1344
XTPRS-232 IR
Tx Rx Tx RxG
Tx Rx
RTSCTS GTx Rx GTxRxG
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTPEXP
+48V
MIC/LINE
113
24
2
3
4
LINK
LAN 2
LAN 1
LAN 3
HDBT
G
DTP
HDBT
2
1234 578 6
DTP CROSSPOINT 84
4
CLASS 2 WIRING
8/
R
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
REMOTE
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
INPUTS
AUDIO OUTPUTS
AMP OUTPUT
COM1
CONTROL
1234G
COM2 DIGITAL I/O
COM3
S
DMP EXPANSION
SGG
1
12 2C34C D-SG+S+V
IR/SERIAL
PWR OUT = 6W
eBUS
RELAYS
OUTPUTS
1
LR 1
LR
3
LR 3
LR
5
LR
2
LR 4 LR 2
LR4
LR
6
LR
Extron Extron
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVERDTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVERDTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVERDTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVERDTP
DTPHDMI 230 Tx
Flat Panel DisplayFlat Panel Display
CATx Cable
up to 330' (100 m)
CATx Cable up to 230' (70 m)
CATx Cable
up to 230' (70 m) CATx Cable
up to 330' (100 m)
RS-232HDMI
HDMI
Extron
DTP HDMI
330 D Rx
Receiver
Extron
DTP HDMI
230 D Rx
Receiver
RS-232
Ethernet
Ethernet
Audio
Audio
Audio
AudioAudio
AudioAudio
HDMI
Extron
DTP T USW 333
DTP Transmitter
Extron
DTP HDMI 230 Tx
Transmitter
Inputs
Outputs
Extron
TLP 1020T
10" Tabletop
TouchLink Pro
Touchpanel
AV
Control
Network
Microphones
Extron
SM 26
Surface Mount
Speakers
Extron
DMP 128 C
Digital Matrix
Processor
Camera
Video Conference
Codec
Table Microphones
Wireless
Microphones
Extron
DTP CrossPoint 84 SA
Scaling Presentation
Matrix Switcher with
DTP Extension
Figure 1. Typical DTP CrossPoint Application
The switchers provide four mono microphone (mic)/line level inputs that can be mixed with
or across one or all audio outputs.
The IPCP models also feature the built-in Extron IPCP Pro 350 control processor, which has
local area network (LAN) Ethernet ports, RS-232 and IR-based control, relays, and digital
I/O controls that can control and monitor a variety of external devices, such as projectors
and lights. The non-IPCP model has one Ethernet port.
The matrix switcher can be remotely controlled via an Ethernet LAN port, a serial port,
or a USB port connection using either the Extron Product Configuration Software, DSP
Configurator software, or the Simple Instruction Set (SIS).
1