Extron electronics NAV SD 501 User manual

1
NAV SD 501 and NAV SD 101 • Setup Guide
This guide provides instructions for an experienced installer to install the Extron NAV SD 501 and
NAV SD 101 scaling decoders and to make all connections. One or more compatible Extron NAV
encoders and one or more decoders form an AV distribution and switching matrix on a managed 1G
IP network.
NOTE: For more information on any subject in this guide, see the NAV SD 501 and NAV SD 101 User Guide, available at
www.extron.com.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and rack or furniture mount the decoder as required.
Step 2 — Rear Panel Connections
HDMI
POWER
12V
2.0 A MAX L
Tx Rx GSG
RS-232 IRR
AUDIO
CONTROLOUTPUT
NAV SD 101
RESET
NAV 1G/PoE+
LAN
HDMI
POWER
12V
2.0 A MAX L
Tx Rx GSG
RS-232IRR
AUDIO
CONTROLOUTPUT
NAV SD 501
RESET
5V/200 mA
USB 2.0
NAV 1G/PoE+EXT
LAN
DDD
CCCHHHEEEGGGFFFAAABBB
Figure 1. NAV SD 501 and NAV SD 101 Rear Panel Features
ANAV 1G/PoE+ port — Connect to an Ethernet LAN on which one or more encoders also reside for streaming and control. This port
can also receive Power over Ethernet (PoE+) to power the decoder (see Power on page 3 for power options).
BExtension port (NAV SD 501 only) — If desired, connect another networked device to this port. The port acts as a networked switch
to the NAV 1G/PoE+ port.
NOTE: The Extension port cannot provide PoE.
CHDMI output port — Connect an HDMI cable between this port and an HDMI display (or a DVI display, with an appropriate adapter).
See LockIt® Lacing Brackets on page6 to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the decoder.
DAUDIO output port — This 5-pole, 3.5 mm captive screw connector outputs the streamed, unamplified, line level analog audio. Connect
an audio device, such as an audio amplifier or powered speakers (see Analog audio output on page6 to wire the connector).
ECONTROL RS-232/IR port — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and IR communication with connected remote controlled devices using an Extron control system
(see Control connector on page6 to wire the connector).
FUSB 2.0 port (NAV SD 501 only) — Connect a USB Type-C cable to USB host or a USB device. See LockIt® Lacing Brackets to
securely fasten the USB connector to the decoder.
NOTE: This connector is limited to supplying 200 mA in USB device mode.
GRESET button — This button initiates three modes of reset (see the NAV SD 501 and NAV SD 101 User Guide, available at
www.extron.com, for details).
HPOWER connector (optional) — Plug the included external 12 VDC power supply into this 2-pole connector for local power (see
Power connector on page6 to wire the connector and Power for power options).
1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.

2
NAV SD 501 and NAV SD 101 • Setup Guide (Continued)
Step 3 — Front Panel Configuration Port Connection
NAV SD 101
NAV
HDCP
VIDEO
CONFIG HDMI LNK
ACT
ANALOG
AUDIO
AUDIO LAN ID
NAV SD 501
NAV
HDCP
VIDEO
CONFIG
ANALOG
HDMI
ACTIVE
HOST -LNK-
-ACT-
NAV EXT
USB
AUDIO
AUDIO LAN IDUSB
CCC
AAABBBDDDFFFGGG
EEE
Figure 2. NAV SD 501 and NAV SD 101 Front Panel Features
AConfiguration port — Connect a PC to the decoder via this front panel USB Mini-B connector for configuration of the decoder.
The port uses IP over USB technology; the IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also
discoverable via Extron Toolbelt (see the NAV SD 501 and NAV SD 101 User Guide; the guide and Toolbelt are available for download
at www.extron.com).
Indicators
BPower LED — Indicates power and startup status, as follows:
• Blinking — The unit is receiving power, either locally or remotely (via PoE) and is booting up.
• Lit steadily — The unit is receiving power, either locally or remotely (via PoE) and is operational.
CNAV LEDs — Indicates status of the streaming input, as follows:
• VIDEO — Indicates status of the video stream.
• Lit steadily — The decoder is receiving a video stream.
• Blinking — A video stream is being decoded, but network errors are present that affect the video quality.
• HDCP — The video stream is HDCP encrypted.
• AUDIO LED — Indicates status of the audio stream.
• Lit steadily — The decoder is receiving an audio stream.
• Blinking — An audio stream is being decoded, but network errors are present that affect the audio quality.
• USB LED (NAV SD 501 only) — Indicates status of the USB stream.
• Lit Steadily - The decoder is actively receiving and sending a NAV USB stream
• Unlit — The decoder is unable to establish a NAV USB stream.
• Blinking - The decoder is not actively sending and receiving a NAV USB Stream.
DAudio LEDs — Indicate the active audio output, as follows:
• HDMI — The embedded HDMI audio output is selected.
• ANALOG — The analog audio output is selected.
EUSB LEDs (NAV SD 501 only) — Indicates the status of the USB stream, as follows:
• Host
• Lit steadily – The decoder is in USB host mode.
• Unlit – The decoder is in USB device mode, the default condition.
• Active
• Lit steadily – A USB device or host is connected to the rear panel USB port.
• Unlit – No host or USB device is connected to the rear panel USB port.
• Blinking – A USB device or hub is connected to the decoder and is attempting to draw more power than the USB port can
supply.
2
page 2
point E > Active > Fast blinking: I don’t believe in Active mode the unit actually
provides power, please conrm with PD

3
FLAN LEDs (see figure 2 on page 2)— Indicate the status of the network connections, as follows:
• NAV LED (NAV SD 501) or LAN LED (NAV SD 101) —
• Link LED — Lit steadily indicates that a network link is established. Blinking indicates a link speed less than 1G.
• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.
• Ext LED (NAV SD 501 only) —
• Link LED — Lit steadily indicates that a network link is established. Blinking indicates a link speed less than 100 Mbps.
• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.
GID button and LED — The recessed ID button identifies the decoder when pressed. The LED blinks three times when the decoder is
paired to a NAV encoder (see Pairing devices via front panel on page5).
Operation
Power
The decoder can be powered in one of three ways:
• Locally, from the included external power supply and via the power connector (see figure1, Hon page 1).
• Remotely, receiving PoE via the NAV 1G/PoE+ port (see A); either from the network switch or from an optional PI 140 Power Injector.
• Locally (H) and remotely (A), with priority on the NAV 1G/PoE+ port. If PoE voltage drops below a threshold, the decoder
immediately transitions to the external power supply with no effect on system operation.
When power is applied, the decoder runs a series of self-tests that blink the front panel Power LED and all other indicators. The decoder
then boots the NAV operating system. It can take approximately 45 seconds for self-test and system startup to complete. When the
process is complete, the Power LED lights steadily.
NOTE: The decoder is NOT operational until the boot process is complete (the Power LED is lit steadily).
System Operation
The decoder can be congured and controlled using embedded web pages or Extron Toolbelt (see the
NAV SD 501 and NAV SD 101 User Guide available at www.extron.com).
NOTE: The “Connection via web pages,” Connection settings, and Pairing devices via front panel procedures (see page 5) may
NOT be necessary if your system includes a NAVigator System Manager.
Connection via web pages
Connection to the decoder and its embedded web pages can be made via either the front panel Conguration (USB) port (using IP over
USB) (see figure2, A) or the rear panel NAV 1G/PoE+ port (see figure1, A).
Access the decoder using HTML pages as follows:
1. Start a web browser.
NOTES:
• Suggested browsers to fully support the NAV system are: Google Chrome™, Mozilla™ Firefox™, and Microsoft Edge™.
• The network must be properly configured for multicasting (IGMP). Failure to do so may result in degraded performance.
2. Enter the IP address of the decoder in the browser Address field.
NOTE:
• Default settings:
Port DHCP IP address Subnet mask
Config (USB)*203.0.113.22
NAV/PoE+ (RJ-45) On
* For the Config port, the address for IP over USB CANNOT be changed.
• If you use IP over USB, Extron recommends waiting a minute after plugging in the cable for your PC to identify the USB
connection as a valid Ethernet port

4
NAV SD 501 and NAV SD 101 • Setup Guide (Continued)
3. Press the keyboard <Enter> key. The browser displays
a privacy error message (see figure 3 at right for an
example in the Chrome browser).
4. Click Advanced (see figure 3, 1). The button changes
to Hide Advanced and explanatory text and a link
appear below the button.
5. Click Proceed to <IP address>(unsafe) (2). The
browser opens to the Login dialog box (see figure 4).
1111111111
1111
1111
2222222222
2222
2222
3333333333
3333
3333
Figure 4. Login Dialog Box
6. Enter the username and password in the appropriate fields (see figure 4, 1and 2) and click Sign In (3). The browser opens to the
home page of the embedded web pages (see figure5 on the next page).
NOTES:
• The default username is admin.
• The factory configured passwords for all accounts on this device have been set to the device serial number. If the password is
reset, the decoder defaults to the default password, which is extron.
• Usernames and passwords are case sensitive.
11
1111
1111
1111
1111
22
2222
2222
2222
2222
Figure 3. Privacy Error Message (in Chrome Browser)
4

5
111111111111111111
2222222222
2222
2222
*
* NAV SD 501 only
Figure 5. Home Page
NOTE: Detailed descriptions of communication, configuration, and monitoring are provided in the NAV SD 501 and NAV SD 101
User Guide, available at www.extron.com.
Connection settings
View and change connection settings as follows:
1. On the home page, click Settings (see figure 5, 1) > Network
Connection (2). The Network Connection pane opens (see figure 6),
showing protected views of the network connection settings.
NOTE: Editing of connection settings is disabled when the device is
assigned to an Extron NAVigator System Manager.
2. To change the settings, click Edit (see figure 6, 1). The Edit button
changes to Save.
3. Click in the desired field (2) and edit it as desired.
4. Repeat step 3 as necessary for other values.
5. Click Save.
Pairing devices via front panel
Pair devices from the front panel as follows:
V SD 101
ID
V
V
V
V
V
1. Use a Tweeker or other small screwdriver to press
and hold the encoder front panel ID button for
approximately 3 seconds, until the ID LED blinks. The
encoder enters pairing mode, which allows decoders
to receive the AV stream (NAV SD 101) or AV and USB
streams (NAV SD 501 only) from encoders.
2. One at a time, use a Tweeker or other small screwdriver to press and
hold the front panel decoder ID button for approximately 3 seconds,
until the ID LED blinks. The decoder is now paired to the encoder.
3. Repeat step 2 for each decoder.
3
1111111111
1111
1111
2222222222
2222
2222
*
* NAV SD 501 only
Figure 6. Network Connection Pane

668-2980-50 Rev. B
09 20
NAV SD 501 and NAV SD 101 • Setup Guide (Continued)
© 2020 Extron — All rights reserved. www.extron.com All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see
the Extron Safety and Regulatory Compliance Guide on the Extron website.
4. Use a Tweeker or other small screwdriver to press and release the encoder front panel ID button. The encoder exits pairing mode.
5. Repeat steps 1 through 4 to pair decoders to other encoders.
After all devices are connected, powered on, and paired, the system is fully operational.
Operation in a System with a NAVigator
The Extron NAVigator is a system manager that easily congures and controls the NAV System. The NAVigator can support a 16 endpoint
system by default, but if a LinkLicense is installed, it can support up to 240 endpoints.
See the NAVigator User Guide, available at www.extron.com for details.
Connection Details
LockIt®Lacing Brackets
1. Plug the HDMI cable or USB (NAV E 501 only) into the panel connection (see 1, at right).
3
333
111
555
444
222
2. Loosen the connection mounting screw from the panel enough to allow the LockIt lacing bracket to
be placed over it (2). The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the connector (3).
4. Tighten the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very
thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel elle est
attachée est très n et peut facilement être dénudé.
5. Loosely place the included tie wrap around the connector and the LockIt lacing bracket as shown (4).
6. While holding the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any excess length (5).
Analog audio output Power connector
Unbalanced Stereo Output Balanced Stereo Output
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
ATTENTION:
• For unbalanced audio, connect the sleeves to the ground contact.
DO NOT connect the sleeves to the negative (-) contacts.
• Pour l’audio asymétrique, connectez les manchons au contact au
sol. NE PAS connecter les manchons aux contacts négatifs (–).
Power Supply
Output Cord
Ridges
Smooth
Captive
Screw
Connector
3"
16 (5 mm) MAX
SECTION A–A
AA
Control connector NAV and EXT connectors
TxRx
RxTx Gnd
IR Device
RS-232 Device
RS-232
Tx Rx GSG
IR
CONTROL
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T568B
TP Wires
12345678
Pins: