EtherWAN EM1100 User manual

Gigabit Ethernet Media Converter
User’s Manual 1
FCC Statement
The FCC (Federal Communications Commission) restricts the amount of
radio frequency emission and radiation coming from computer equipment.
The equipment introduced in this manual has been tested and found to
comply with the limits for a Class A digital device pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user is required to correct the
interference at his/her own expense.
Any changes or modifications not expressly approved by the manufacture
would void the user’s authority to operate the equipment.
Trademarks
Product names mentioned in this manual may be trademarks or registered
trademarks of those products.
All trademarks or brand names mentioned are properties of their respective
companies.
Preface
This manual describes how to install and use the Gigabit Ethernet Media
Converter. The Converter introduced here provides one channel media
conversion solution:
10/100/1000Base-TX ↔1000Base-SX/LX
1000Base-SX/LX ↔100Base-FX
The Gigabit Ethernet Media Converter fully complies with IEEE802.3
10Base-T, IEEE802.3u 100Base-TX/FX, IEEE802.3ab 1000Base-T, and
IEEE802.3z 1000Base-SX/LX Ethernet standards.
In this manual, you will find:
yProduct overview
yFeatures on the media converter
yIllustrative LED functions
yInstallation instructions
ySpecifications

2 User’s Manual
Table of Contents
FCC STATEMENT ....................................................................1
TRADEMARKS ..........................................................................1
PREFACE...................................................................................1
TABLE OF CONTENTS..............................................................2
INTRODUCTION........................................................................3
PRODUCT OVERVIEW ...................................................3
PRODUCT FEATURES ...................................................4
PACKING LIST ..............................................................4
ONE-CHANNEL MEDIA CONVERTER .....................................4
PHYSICAL PORTS.........................................................4
PORT STATUS LEDS....................................................4
INSTALLATION.........................................................................6
SELECTING A SITE FOR THE EQUIPMENT .......................6
CONNECTING TO POWER..............................................6
INSTALLING IN A CHASSIS .............................................7
SPECIFICATIONS ......................................................................8

Gigabit Ethernet Media Converter
User’s Manual 3
Introduction
The Gigabit Ethernet Media Converter provides one channel for media
conversion between 1) 10/100/1000Base-TX and 1000Base-SX/LX or 2)
1000Base-SX/LX and 100Base-FX. It can be used as a stand-alone device
or with a standard 19” chassis as shown below.
Product Overview
10/100/1000Base-TX↔1000Base-SX/LX Media Converter
1000Base-SX/LX↔100Base-FX Media Converter
<NOTE> The chassis is to be ordered separately.

4 User’s Manual
Product Features
yOne-channel media conversion between:
10/100/1000Base-TX and 1000Base-SX/LX
1000Base-SX/LX and 100Base-FX
yTX port support speed and duplex mode auto-negotiation and auto-MDIX
yGigabit Ethernet Fiber media support auto-negotiation and allow either:
Multi-mode fiber or Single-mode fiber that using SC connector
yFast Ethernet Fiber media allow either:
Multi-mode fiber that using SC, ST, VF-45, MT-RJ, or LC connector
Single-mode fiber that using SC connector
yStore-and-forward mechanism
yNon-blocking full wire-speed forwarding rate
yBack-pressure & IEEE802.3x compliant flow control
ySupport 4096 MAC Addresses and 2M bits Memory Buffer
yFront panel status LEDs
yUsed as a stand-alone device or with a chassis
yHot-swappable when used with a chassis
yExternal AC to DC power adapter
yWall-mountable
Packing List
When you unpack this product package, you will find the items listed below.
Please inspect the contents, and report any apparent damage or missing
items immediately to your authorized reseller.
yThe Media Converter
yUser’s Manual
yAC to DC Power Adaptor
One-Channel Media Converter
Physical Ports
This converter provides one TX port and one FX port. For the FX port, it
provides options of either multi-mode or single-mode fiber accommodating
SC connector. For the TX port, it uses RJ-45 connector and supports auto-
MDIX for uplink purpose.
Port Status LEDs
The LED indicators give you instant feedback on status of the converter:

Gigabit Ethernet Media Converter
User’s Manual 5
10/100/1000Base-TX↔1000Base-SX/LX Media Converter
LEDs State Indication
Steady Power feeding inPWR
Off No power
Steady A valid network connection established.
LNK stands for LINK.
Flashing Transmitting and receiving data.
ACT stands for ACTIVITY.
LNK/ACT
(TX)
Off Neither connection nor activity existing.
Steady A valid network connection established.
LNK stands for LINK.
Flashing Transmitting and receiving data.
ACT stands for ACTIVITY.
LNK/ACT
(SX/LX)
Off Neither connection nor activity existing.
Steady Connection in full duplex mode.
FDX stands for FULL DUPLEX.
Flashing Collision occurred.
FDX
Off Connection in half duplex mode
1000 Steady Connection at 1000Mbps speed.
100 Steady Connection at 100Mbps speed.
1000, 100 Off Connection at 10Mbps speed.
1000Base-SX/LX↔100Base-FX Media Converter

6 User’s Manual
LEDs State Indication
Steady Power feeding inPWR
Off No power
Steady A valid network connection established.
LNK stands for LINK.
Flashing Transmitting and receiving data.
ACT stands for ACTIVITY.
LNK/ACT
Off Neither connection nor activity existing.
Installation
This chapter gives step-by-step installation instructions for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not
be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
- The ambient temperature should be between 32 and 113 degrees
Fahrenheit (0 to 45 degrees Celsius).
- The relative humidity should be less than 95 percent, non-condensing.
- Surrounding electrical devices should not exceed the electromagnetic
field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
- Make sure that the equipment receives adequate ventilation. Do not
block the ventilation holes on each side of the equipment.
- The power outlet should be within 1.8 meters of the product.
Connecting to Power
This Converter is a plug-and-play device.
Step 1: Connect the supplied AC to DC power adapter to the receptacle at
the back of the converter.
Step 2: Attach the plug into a standard AC outlet.

Gigabit Ethernet Media Converter
User’s Manual 7
Installing in a Chassis
The Converter is designed to fit into any of the expansion slots on a
rackmount chassis.
Step 1: Unscrew the carrier from the desired expansion slot on the chassis.
Step 2: Fit the converter onto the carrier.
Step 3: When the converter is completely seated onto the carrier, insert
the carrier to the guide rails of the expansion slot.
Step 4: Carefully slide in the carrier until it is fully and firmly fit the chassis.
Step 5: Fasten the carrier to the chassis by the screws.
<NOTE> Never insert any converter into the chassis directly without using the
supplied carriers. The carriers allow secure and consistent placement
of the converters into the chassis’ backplane without causing any
damage.

8 User’s Manual
Specifications
Applicable Standards IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-SX/LX
Fixed Ports One 10/100/1000Base-TX port and one
1000Base-SX/LX port
One 1000Base-SX/LX port and one 100Base-FX
port
Speed 10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
2000Mbps for full-duplex
Forwarding rate 14,880pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
LED Indicators PWR; LNK/ACT (TX); LNK/ACT (SX/LX); FDX;
100; 1000
PWR; LNK/ACT (1000Base-SX/LX); LNK/ACT
(100Base-FX)
Dimensions 80.3mm (W) × 109.2mm (D) × 23.8mm (H)
(3.16” (W) x 4.3” (D) x 0.94” (H))
Weight 150g (0.33lb.)
Power External power adaptor
0.35A @ 12VDC
Power Consumption 4.25W Max.
Operating Temperature 0℃~ 45℃(32℉~ 113℉)
Storage Temperature -10℃~ 70℃(14℉~ 158℉)
Humidity 5 ~ 95%, non-condensing
Emissions FCC Part 15 Class A, CE Mark Class A