Eye Sight ES-IPS507 User manual

H.264 IP Camera Server
ES-IPS507
User Manual
V1.3
IPS507 Three channels wired and four channels wireless
video input server
IPS507WD Four channels wired video input server
1

2
Welcome to use our IPS507 server
Please read the manual carefully before you use it, which will provide you a great
help. We do our best on improving products software, hardware function, and our
service quality.
Please contact the dealer once any doubt on using or product function are not the
same with the manual.
Contents
1. Introduction
1.1 Usage
1.2 Declaration
2. Product description
2.1 Brief Introduction
2.2 Features
2.3 Packing list
2.4 Network requirements and software operation environment
2.5 Rear Panel
2.6 Keyboard Introduction
3. Operation
3.1 Installation
3.2 Image Window page

3
4．Server Management
4.1 Setup
4.1- Channel Parameters⑴
4.1- Network System Settings⑵
4.1- Hardware Management⑶
4.1- Alarm Input/Output⑷
4.1- Storage⑸on IPS507
4.1- Talkback⑹
4.1- Media Center⑺
4.1- User Management⑻
4.1- 3322 DDNS⑼
4.1- DynDNS⑽
4.1-⑾Email Notification
4.1- Monitoring⑿
4.1- Update⒀
4.2 Disconnect / Connect
4.3 Login Information
4.4 Talkback
4.5 Delete
5．Basic Setting
5.1 PC-Recording
5.2 Playback

4
5.3 Motion Detection
5.4 Alarm Setting
5.5 Format hard disk
Chapter 1 Introduction
IPS507 server uses the latest codec algorithm to transfer the analog AV signal
to digital by H.264 compression algorithm . Using TCP/IP protocol to send
low-bit-rate AV encoded data to remote PC by IP package, achieve the remote
transmission, monitoring and storage of AV signal to digital. It’s built-in Web
server,the users can use the standard IE browser on their PC or use specialized client
access to visit,watch images and control camera’s lens/PTZ from the front
end,achieve the omnibearing real-time surveillance.It can be widely used in building
control,road monitoring,industrial monitoring, large-scale remote monitoring,remote
care,online unicast and so on.
1.1 Usage
Help you correctly use IPS507 series products.
1.2 Declaration
Please setup the IPS507 server according to this manual strictly.The software
and hardware will continue upgrade and update.And the change will not give prior
notice,please take attention on the announcement from our website.
Chapter 2 Product Description
2.1 Brief Introduction

PS507 server is designed as an embedded control solutions for IP network
video and data surveillance.Using the faster computing speed DSP chipset and the
latest H.264 codec algorithm, really achieve the low-rate stream high definition.Every
frame on CIF is only 1.0KB to 1.5KB. Specially suitable for network transfer.The
max transmission speed is up 25fps(PAL)/30fps(NTSC)
IPS507 is a multi-use IP camera server. Besides providing 3 channels wired AV
input,4 channels wireless 2.4G AV input and network port, it also have 1 channel
local AV output and RS485 controlling port.
IPS507 has in-built Web server, stable and reliable system operation.Visit remote
images by specialized client port and IE browser.Support multiple network
type,include dynamic IP and static IP/PPPOE,to realize the function of image and
sound transfer on network. It also support the function of talkback, multi-linkage
alarm, motion detection and other advanced function.
5

6
2.2Features
Model 3 channel wired channels A/V
inputs 4 channel wireless channel (2.4GHz) A/V inputs Local A/V outputs
IPS507 Yes Yes Yes
IPS507WD Yes(4wired) NO NO
¾3 way audio/video control: front panel, remote controller, remote PC.
¾Real time remote surveillance of multi audio/video sources.
¾Support both WAN(via ADSL MODEM) and LAN connection.Note:3G dial-up
connection is under developing.
¾Real time video recording via local USB port or on remote PC.
¾Playback history recording and picture on remote PC.
¾Motion detection: automatic video capture or snap shot when motion is detected.
¾External alarms input/output function: such as PIR motion detection, smoke
detector, gas alarm.
¾PTZ remote control(L/R/UP/DOWN/F+/F-) via optional PTZ decoder.
¾3-level user management system: operator , administrator and super
administrator with different level of privileges.
¾Image compression format: H.264
¾Support DynDNS.org & Oray.net & 3322.org free Dynamic DNS service
¾Support catalog server to alias a dynamic IP address
2.3 Parameters
Parameters setting
Image
Compression H.264 format
Image resolution
PAL：D1（704x576）/HalfD1(704x288)/ CIF(352x288)/ QCIF
(176x144)
NTSC：D1（704x576）/HalfD1(704x288)/ CIF(352x288)/
QCIF (176x144)
Image
Transmission Rate PAL：1-25fps，NTSC：1-30fps

7
Interface for
Storage devices 1 USB ports（USB2.0 port for storage）
Talkback port 1 USB port ( USB port for audio)
AV input 3 channels wired,4 channels wireless at 2.4GHz
AV output PC :4 channels.Local:1 channel
Recording format DAT
PTZ Control RS485
Network interface RJ-45/10-100 Base T
Network Protocol Support TCP/IP，UDP, ARP, HTTP, DHCP, FTP etc
Dimension 205×130×47(mm)
Software upgrade Automatic upgrade with the included software
Video playback IPSClient software
Security Access rights setting: Super administrator giving the rights
according to the new user
Working
Temperature 0 – 50℃
Power supply DC 5V/3A
Power
consumption < 10W
2.4 Packing List
Open the package and check the items contained against the following list:
One IP Camera Server
One DC AC110~240 5V/3A Power Supply
One AV cable and one T568B standard network cable
One BNC/ AV adapter
One CD（IPS507 Driver）
One remote controller
One Audio to USB adapter
Contact us immediately in the case of any damaged or short of contents.
2.5 Network requirements and software operation environment
IPS507 series products support 10/100M self-adaptive network port, can connect
to 10/100M or 100/1000M self-adaptive network environment. Due to the 7 channels
video stream, please keep each device’s bandwidth above 2M to ensure the normal
operation.
Related equipment software can be run in the following Windows operation system

zWindows XP SP2 or above
zWindows 2000
zWindows 2003
zVista
zWindows 7
Advise to use IE 6.0 or above browser
System configuration requirements:
●CPU:2.4GHZ or above
●Memory:512M or above
●Network Card: 10-100M or above
●Display Card: 128M
2.6 Rear Panel
2.7 Keyboard Introduction
8

The buttons and indicators are described as below:
① GUD: a button for system arming/disarming upon external inputs
GUD stands for “guard”, armed for arming and disarming , the system
manually following the same working mechanics of the remote controller.
Notes:
Arming manually: the system falls under surveillance when “GUD” or
“D” on the remote controller is pushed down; the server buzzer beeps
twice if successful armed.
Disarming manually: In the monitoring mode, push “GUD” or “D” on the
remote controller again to disarm the system; and the server buzzer beeps
twice too.
Indicator for GUD⑾：It turns on when the system is armed and turns off when it is
disarmed manually.
② MTD: a button for system arming/disarming of motion detection
MTD stands for “motion guard”, meant for setting the motion detection
function to keep watch on the channels under surveillance, following
the same way as GUD.
This button function is the same as “B” on the remote controller.
Indicator of MTD : t turns on when the system is armed manually and⑩turns off
when it is disarmed.
③ USB: a button for USB plug
The button is meant for controlling USB plug. The USB indicator is⑨
light upon detection of USB devices mounted and turns off when the
button is pushed down for plugging the devices out in a safe way.
The function of this button is the same as “C” on the remote controller.
9

CHS: Channel switching button:
CHSstandsof “channels”, used to switch the local output channels. The
switch of wireless channels is synchronous with the remote monitoring
channels.
The function of this button is the same as “A” on the remote controller.
Indicator : It turns on when press “CHS”.⑧
④ USB port
USB port: 2 ports
First port: The server will automatically recognizes the USB devices,
lights when plugged in and went out when they are removed.
Second port: Earphone port for audio.Indicator is lighting when talking.
⑤ RUN: an indicator of normal operation
This indicator lights turn on when the system is under normal operation,
went out when reset。
⑥ NETWORK: an indicator of network status
This indicator lights turn on when the system network works normally.
⑦ POWER: a power indicator
It is constantly lights when the system is powered on.
⑧ GUD+USB : a indicator of return to default
Press those two keys above 5 seconds it will return to default.
Chapter 3 Operation
3.1 Installation
First, open the included CD; Second, Please double click the①
driver , install to your PC, it will have a icon on your PC
desk after successful installed.
10

Double click the “IPSClient”② , it will come out a dialogue.
Please entering the user name and password after click. Default user name is “admin”,
no password.
③Below image window will display upon successful login.
Software interface divides into 4 parts：
11

○ 1Video window ○ 2Basic
setting and management
○ 3LAN searching: search video servers from LAN
○ 4Network setting
3.2 Image Window page
Video window①: video display of the network video server, there shows data of
name, time, frame, server address under each channel.
1)Image function
12

C1 : Channel name, can be changed
Time :2009-9-1 21 :29 :24
IP address : shows WAN/LAN IP address or domain name
Speed : real transferring frames per second
2)Click image via right button to get follow function
Close :close present channel image
Record: record present channel. When recording, it has a red point coming out, but to
choose well saving path, more description in 5.1
Snapshot:Taking picture for present image, manage taken pictures: text font text①②
position text format text custom saving path picture format and watermark③④ ⑤ ⑥
Audio out: Open audio out, a speaker icon will come out.
13

Basic setting and management②: basic setting of image and selected server,
multi-server management.
LAN searching: search video servers from LAN③
First login client software, find LAN searching window, click , available IP
address will coming out as below picture:
choose it then click .
④Network setting: User can add the already on line device to server list on
software.
Write all info as above picture and confirm by click .
Name: can write whatever user want,
User and pass: device user and password
Addr: WAN IP address
Port: client software port, above 8080
PTZ contro⑤l：No matter which video server's video screen has been dragged into
the video window, it all can be controlled ( the camera should be connected with
rotator and decorder ).
Click image and choose the control protocol ,
, click to set up.
full function icon color adjust
focus+ and- Zoom in and out auto crusion
14

default。
Zoom function
Chapter 4 Video server setting
4.1 Video Server Setting
Select a on line video server in list, right click and choose settings, enter setting page.
4.1- Channel parameters⑴
15

Name: name for each video channel
CBR: fixed stream( the WAN network speed will influence the fixed stream)
Mobile: set to show images in mobile phone or not
Resolution: for video images, there are 4 types:
“D1⒈（704×576）”
“HalfD1⒉（704×288）”
“CIF⒊（352×288）”
“QCIF⒋（176×144）”
Image FPS and quality: It has different quality in different image resolution. User can
adjust it according the video images.
Fixed stream and browse in mobile phone is the factory default setting. In order to get
better quality, please do not mark in each option, and adjust the image resolution,
stream, frame to get better image quality.
Notes: please save as defaulted after changed the settings, otherwise it will recall to
factory default setting when server power off or restart.
4.1- Network system setting⑵
16

TV systems: PAL/NTSC
Name: name for server
Network type：dynamic IP/static IP/ PPPOE auto dial-up Internet access
Working port: used for remote client software browsing
web port: for web
MAC address: server MAC address
IP address: server address in LAN
Subnet Mask: set up comply with router
Gateway: set the gateway in LAN
DNS: Please fill the correct DNS(different place with different DNS address), please
inquire from local Service providers.
Refer to above information, setting in router, add IP address, setting port range
forward and DNS, then the IP server can be visited in WAN
17

4.1-⑶Hardware setting
Output to local monitor
Auto: user can select auto-switch in monitor, as well as the switch time for each
channel.
18

Manu: select to display one channel by manual.
Notes: audio will output to monitor follow video(video and audio are in same
channel)
4.1- Alarm input/output⑷
Input/output link
1、Input: there are 4groups external sensor signals, with Nopen(Normal open) and
Nclose(Normal close) status.
2、Relay output link: there are 4groupes Relay output.
For example, External sensor(PIR detectors, Smoke detectors and door magnet), the
default status is Nopen, then it must be Noclose in the software. When alarm sensor is
triggered, the nopen will change to nclose in relay, and send signal to external alarm
like speaker.
Buzzer alarm link: when alarm sensor is triggered, user can choose buzz link to alarm
or not.
Motion detection/relay link: when user need to enable this function, please set
external alarm equipment(ex: speaker). Notes: the motion signals, can be output to
any relay(to any external alarm equipment)
3、Completed all settings, please activate the motion detection setting in 5.3
4、PC audio alarm link, relative reminds in the images of client software, please refer
19

to alarm management setting 5.4
4.1- Storage⑸On IPS507
Storage: videos,
Continual recording, motion detector, Prerecorded( prerecorded can work with others,
but continual recording and motion detector can not).
1, User can set different video recording types toward to the 4 channels, like disable,
continuous, motion and pre-record. Default to Disable and pre-record.
2, Recording Schedule. Recording time can be set as 24Hours or Plan. When choose
Plan, pls relatively set up details in below time schedule.
Motion detection alarm,recording
Detected USB moveable storage card
4．1- Talking⑹
Enable talkback function(that is same function in 4.4)
4.1-⑺Media Center
20