Eye Vac EYEVAC+ User manual

User Manual
EyeVac Plus.indd 1EyeVac Plus.indd 1 4/1/21 2:57 PM4/1/21 2:57 PM

2
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
This electrical appliance must always be used according to the following safety instructions. Save these
instructions as this manual contains important safety and operating information. When using an electrical
appliance, basic precaution should always be followed, including the following:
READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS APPLIANCE:
To reduce the risk of fire, electric shock or injury:
1. Always press the Vacuum Power button on the bottom of the unit to the off position, and the trash bin
Power button on the top of the unit to the off position before unplugging the EyeVac+.
2. Always unplug the appliance before cleaning or servicing it. Do not unplug by pulling the cord; to unplug,
grasp the plug, not the cord.
3. Do not let the EyeVac+ be used as a toy. Close attention is necessary when used near children. Do not use
in Auto mode or leave appliance plugged in near children, infants or small animals.
4. Do not pull or carry the appliance by the cord. Do not run the appliance over the cord, close a door on the
cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.
5. Do not use the appliance if the cord or plug is damaged.
6. Do not handle the plug or appliance with wet hands.
7. Do not use appliance on wet surfaces.
8. Do not expose to rain.
9. Do not use appliance to dispose of water or damp materials such as mud, tile grout, plaster filler, or
caulking. Do not use to pick up any liquid or wet objects.
10. Do not use appliance to vacuum up flammable or combustible liquids, such as gasoline. Do not use in
areas where these liquids may be present.
11. Do not use this appliance to vacuum up burning or smoking materials, such as cigarettes, matches or hot
ashes.
12. Keep hair, loose clothing, and all parts of the body, especially fingers, away from openings and moving
parts.
13. Do not put any objects into appliance openings or use with any openings blocked or plugged.
14. Do not use this appliance to pick up hard or sharp objects or other large surface litter. Pick these up by
hand before vacuuming.
15. Do not operate without the Lid and Filters properly in place.
16. Use the appliance only as described in this Use and Care Guide.
17. Turn appliance off (both Power buttons) before removing or replacing the Canister or Filter.
18. Unplug appliance before cleaning or maintenance.
19. If the appliance is not working as it should, call for instructions where to send for repair. Do not attempt
to repair, as it will invalidate your warranty.
20. When cleaning the outside of the appliance, wipe with a damp cloth to reduce the static electricity on
the outer surface.
WARNING! To reduce the risk of electric shock, do not use on wet surfaces. Do not expose to rain. Store
indoors.
EyeVac Plus.indd 2EyeVac Plus.indd 2 4/1/21 2:57 PM4/1/21 2:57 PM

3
1. Canister Lid
2. Pre-Motor Filter
3. Vacuum Canister
4. Serial Number
(located on back of unit)
5. Sensor- trash bin
6. Inlet
7. Sensor - Vacuum
8. Vacuum Manual Activation Button
9. Vacuum Power button
10. Vacuum Auto mode
11. Vacuum Manual mode
12. Vacuum Canister full indicator
13. Exhaust Filter Housing
14. Exhaust Filter
(not shown, located on back of unit)
15. Trash bin lid
16. Trash bin lid Power button
DESCRIPTION OF EYEVAC+
Save These Instructions
For Household Use Only
EyeVac Plus.indd 3EyeVac Plus.indd 3 4/1/21 2:57 PM4/1/21 2:57 PM

4
BEFORE USING FOR THE FIRST TIME
Replace Trash Bags
Opening the Lid Top
1. Remove EyeVac+ from packaging and set upright on any non-carpeted flooring.
2. Plug unit into any standard 120V(US) AC electrical outlet.
NOTE: EYEVAC+ CANNOT BE USED WITH A CONVERTER OR ADAPTER
3. Press the Vacuum Power button to the MAN position for Manual operation or to the Auto position for
automated use. The Power indicator light will illuminate when the Power button is in either of these
positions. Switch the trash bin Lid Power button to the On position. Your EyeVac+ is now ready for use.
Lift off the trash bin lid
Wave hand in front of the sensor The Infrared sensor activates the motor
and the trash bin Lid will open. The lid
will open and close automatically 5
seconds after the last sensor activation.
Place a 13 Gal liner bag inside
the EyeVac+
Place the trash bin
lid back on
Tip: To keep the trash bin lid open, wave your hand in front of the trash bin lid Sensor for 3 seconds. The
trash bin lid will open and remain open. To close Lid and return to normal operation, wave your hand in
front of the trash bin lid Sensor for 3 seconds.
1
1 2
2 3
EyeVac Plus.indd 4EyeVac Plus.indd 4 4/1/21 2:57 PM4/1/21 2:57 PM

5
Open the Canister and ensure the
Pre-Motor Filter is aligned properly and
in place. Then, re-insert the Canister.
EyeVac+ will not operate if the canister
is not inserted properly.
Canister FULL
Press the Vacuum Power button (locat-
ed on the bottom of the unit) to turn
ON. EyeVac+ will be in Auto mode. Press
the Vacuum Power button again to
select Manual mode
When ready, simply sweep debris towards
the Inlet. If in Auto mode the Vacuum
Sensors will detect the sweeping motion.
If in Manual mode simply tap the Manual
Activation button and the Vacuum will
activate.
As debris accumulates, the Canister will
need to be emptied. The Canister full
indicator illuminates Red to let you know
when its time to empty the Canister.
Plug in your EyeVac+
in the desired location.
Press Power button
to indicate either Manual or Auto modes
1
3
5
4
2
Canister full
EyeVac Plus.indd 5EyeVac Plus.indd 5 4/1/21 2:57 PM4/1/21 2:57 PM

6
USER MAINTENANCE INSTRUCTIONS
CLEANING THE PRE-MOTOR FILTER
1. To empty the EyeVac+ Canister, press the Vacuum Power button to the off position, press the trash bin lid
Power button to the off position, and unplug the unit.
2. Pull the Canister outward from the bottom of the Bin Cavity. Grasp the Canister Grip firmly and lift it out
and away from the EyeVac+ Main Unit.
3. Holding the Canister firmly with one hand, grasp the Canister Lid Handle with the other hand and pull
the Lid straight up and out to remove.
4. Turn the Canister upside down over a trash can. Make sure you empty all dirt and debris from inside and
below the Bin. To ensure that all the dirt spills out, tap the side of the Canister gently against the edge of
the trash can. Re-attach the Canister Lid to the top of the Canister.
5. Clean Sensors, Dirt Inlet area, Canister, Canister Lid and Canister Cavity with a damp rag or towel. Do not
use soap or alcohol to clean sensors.
6. After all parts are fully dried, insert the assembled Canister with Lid fitted snugly into position and Pre-
Motor Filter locked into place. The 2 grooves in the bottom of the Bin fit easily over the rod in the front of
the unit. Grasp the Canister grip and lock the Canister back into position.
NOTE: Make sure all parts are completely dry before reassembly.
HEALTH TIP: If you suffer from allergies or asthma, take the Canister outdoors to empty. As you empty
the dirt into the trash can, gently tap the Canister against the side of the can to remove loose debris.
To maintain optimal performance, the Pre-Motor Filter will need cleaning whenever the suction is not
strong. The Pre-Motor Filter must be clean and free of elements, which might hinder the flow of air.
1. To empty the EyeVac+ Canister, press the Vacuum Power button to the off position, press the trash bin lid
Power button to the off position, and unplug the unit.
2. Pull the Canister outward from the front of the Bin Cavity. Grasp the Canister grip firmly and lift it out and
away from the EyeVac+ Main Unit. Locate the Pre-Motor Filter Handle.
3. Remove the Pre-Motor Filter by grasping the Filter Handle and turn counter-clockwise to the unlock
position. Pull Filter straight up and out of the top of the Canister. Rinse under running water to clean. If
needed a mild soap and soft bristled brush can also be used.
IMPORTANT! Dry thoroughly before use.
4. Slide the Pre-Motor Filter back into the top of the Canister. Rotate clockwise to the “lock” position. Put the
Canister back into place.
5. If a new Filter is needed, replace with standard filter cartridges. Make sure that it fits snugly in the Filter
Holder. Replacement Filters are available through the Customer Service Department.
IMPORTANT! NEVER OPERATE THE EYEVAC+ WITHOUT THE PRE-MOTOR FILTER PROPERLY IN PLACE.
EyeVac Plus.indd 6EyeVac Plus.indd 6 4/1/21 2:57 PM4/1/21 2:57 PM

7
CLEANING THE EXHAUST FILTER HOLDER
CLEANING THE CANISTER
STORAGE
1. To clean the Exhaust Filter Holder, press the Vacuum Power button to the off position, press the trash bin
lid Power button to the off position, and unplug the unit.
2. The Exhaust Filter Holder slides up and out of its housing on the side of the unit.
3. Gently pull the Filter out of the Filter Holder.
4. Tap Filter gently against trash container to free and eliminate excess dirt and debris.
5. To clean the Filter, wash in mild soap and water; rinse and dry thoroughly before assembly
6. Slide the Holder back into the unit with the Filter facing outwards.
IMPORTANT! NEVER OPERATE EYEVAC+ WITHOUT THE EXHAUST FILTER & FILTER HOLDER PROPERLY IN
PLACE.
The Canister should be washed periodically.
1. To clean the EyeVac+ Canister, press the Vacuum Power button to the off position, press the trash bin lid
Power button to the off position, and unplug the unit.
2. Wash the Bin in warm water using a mild soap. Avoid harsh or abrasive cleaners or sponges. Rinse
thoroughly.
TO AVOID DAMAGE, DO NOT PLACE CANISTER IN THE DISHWASHER.
3. Let it air dry. Make sure the Canister is completely dry before putting it back into the EyeVac+.
4. Insert the assembled Canister following the instructions outlined in the USER MAINTENANCE
INSTRUCTIONS.
IMPORTANT! Other than cleaning the Pre-Motor Filter and replacing the Exhaust Filter Holder, as
described in this Owner Manual, this EyeVac+ is not user serviceable. There are no user serviceable
parts inside the unit. Servicing by our Authorized Service Center is required to avoid damage to internal
components.
1. To store the EyeVac+ press the Vacuum Power button to the off position, press the trash bin lid Power
button to the off position, and unplug the unit.
2. Store EyeVac+ indoors, in a clean, dry place.
3. Never store EyeVac+ while it is still plugged in. Never wrap cord tightly around the appliance, use the
Cord Storage area on the back of the EyeVac+ unit. Do not put any stress on the cord where it enters the
unit, as it could cause the cord to break.
WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT USE OUTDOORS OR ON WET SURFACES.
EyeVac Plus.indd 7EyeVac Plus.indd 7 4/1/21 2:57 PM4/1/21 2:57 PM

8
TROUBLESHOOTING
Problem
Vacuum:
EyeVac+ will not turn on/
no power
Does not pick up debris
Suction not strong
Canister full indicator light
is on
Sensor does not activate
Debris at Inlet before unit is
powered on
Status indicator light
blinking
1. Not firmly plugged in
2. EyeVac+ is in off position
3. Pre-Motor Filter is not in correct
position
4. No power in wall plug
5. Blown house fuse or
tripped circuit breaker
1. Dirt inlet is blocked
2. Canister is full
3. Debris may be too large
for Inlet
1. Pre-Motor Filter may be dirty
1. Canister is full
1. EyeVac+ is not in Auto mode
1. EyeVac+ is not in Auto
mode
1. EyeVac+ sensors have been
shut off for 30 seconds which
caused power to the motor to
be shut off
1. Press Power button to turn off EyeVac Air
2. Clean path of dirt Inlet
3. Empty Canister
4. Clear large debris
1. Press Power button to turn off
2. Clean filters when needed
1. Press Power button to the Auto position
1. Press Power button to the Manual position
2. Activate EyeVac+ manually
1. Press Power button to turn off
2. Empty the Canister
3. Clean all filters
1. Press Power button to the power off
2. Check Pre-Motor Filter, and Exhaust
Filter to ensure they are clean.
3. Clean sensors with warm water and Q-tip.
DO NOT USE ALCOHOL OR SOAP.
1. Plug in firmly
2. Press Power button to Manual or
Auto position
3. Ensure that Pre-Motor Filter is locked and flush
with Canister in place
4. Check house fuse or circuit breaker
5. Have a qualified licensed electrician replace
house use or reset circuit breaker.
6. Remove Canister to check switch inside cavity
above Pre-Motor Filter is positioned
Possible Cause Possible Solution
If your problem is not listed, please contact Customer Support.
EyeVac Plus.indd 8EyeVac Plus.indd 8 4/1/21 2:57 PM4/1/21 2:57 PM

9
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes. To prevent
possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product was purchased. They can take this
product for environmentally safe recycling. This appliance is a dry pick-up, Canister type vacuum cleaner
for household and indoor use. It is also a general-purpose vacuum cleaner, which can be used for hard floor
cleaning.
TROUBLESHOOTING-CONTINUED
Trash Bin
No power to the lid
Lid not opening or
closing all the way
1. EyeVac+ is not plugged in
2. Trash bin sensor is off
3. Liner bag is not bag not
properly secured
4. The Motor Interruptor
Feature is activated
5. EyeVac+ is not on appropriately
placed
1. EyeVac+ is not plugged in
2. Trash bin sensor is off
3. Liner bag is not bag not
properly secured
4. The Motor Interruptor
feature is activated
5. EyeVac+ is not appropriately
placed
1. Plug in firmly
2. Ensure the lid Power switch is in the on
position.
3. Ensure the liner bag is not covering the Power
connector, located on the back of the lid
4. Ensure there is no objects or pressure on the lid
5. Power on and off using the on/off
Power switch located on the back of the lid
Do not push or force the lid up or down
6. Do not place EyeVac+ too close to a wall
1. Plug in firmly
2. Ensure the lid Power switch is in the on
position.
3. Ensure the liner bag is not covering the Power
connector, located on the back of the lid
4. Ensure there is no objects or pressure on the lid
5. Turn the Power on and off using the on/off
Power switch located on the back of the lid
Do not push or force the lid up or down
6. Do not place EyeVac+ too close to a wall
If your problem is not listed, please contact Customer Support.
EyeVac Plus.indd 9EyeVac Plus.indd 9 4/1/21 2:57 PM4/1/21 2:57 PM

10
LIMITED WARRANTY
One-Year Limited Warranty. What is covered: JPaulJones, LPTM warrants to the first retail purchaser of this EyeVac+
that should this product or any part be proved defective in materials or workmanship from the date of proof of
purchase for a period of one (1) year, then it will be subject to the terms of this one-year limited warranty. Such defects
will be replaced, or credit issued at JPaulJones, LP’s option, without charge for parts or labor directly related to the
defect. Limitations and Exclusions: This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. This warranty does not apply to any cost incurred for removal or re-installation, or to any
product or part thereof which has suffered through normal wear and tear, alteration, improper installation, physical
abuse, misuse, neglect or accident. Nor does it cover defects caused by shipment to JPaulJones, LP or repair or service
of the product by anyone other than JPaulJones, LP. Damage resulting from an unforeseen circumstance including
but not limited to fire, flood, earthquake, and other natural causes will be excluded. This Limited warranty is in lieu of
all other warranties, express or implied either in fact or by operations of law, statutory or otherwise, including, but not
limited to any implied warranty of merchantability or fitness for a particular use. JPaulJones, LP does not authorize any
other person to assume any liability beyond the warranty herein described. In no event, whether based in contract or
tort shall be liable for incidental, inconsequential, indirect, special or punitive damages of any kind from the use of this
product. In no event shall be liable for damage in excess of the purchase price. EyeVac+ not for commercial use.
For Warranty Service, submit a Service Request at http://eyevac.com/connect/ or contact: JPaulJones, LP, 7500 Rialto
Blvd., Bldg. 1, Suite 122, Austin, TX 78735 or call 512-485-3050.
©2014 JPaulJones, LP Intellectual Property. All rights reserved, JPaulJones, LP, JPaulJones, LP logo and all other marks
contained herein are trademarks of JPaulJones, LP Intellectual Property and/ or JPaulJones, LP affiliated companies.
JPaulJones, LPTM
7500 Rialto Blvd, Bldg. 1 STE. 122
Austin, TX 78735
[phone]
For service and general inquiries please visit www.eyevac.com/connect
EyeVac Plus.indd 10EyeVac Plus.indd 10 4/1/21 2:57 PM4/1/21 2:57 PM

EyeVac Plus.indd 11EyeVac Plus.indd 11 4/1/21 2:57 PM4/1/21 2:57 PM

EyeVac Plus.indd 12EyeVac Plus.indd 12 4/1/21 2:57 PM4/1/21 2:57 PM