EyeCU Ward 1.0 User manual
Ward 1.0
User Manual
ENGLISH
Acronyms and Abbreviations
3
Acronym/ Abbreviation
Definition
A
Ampere
AC
Alternative Current
DHCP
Dynamic Host Configuration Protocol
EyeCU
Eye
See You
IP
Internet Protocol
IPC
IP Camera
LAN
Local Area Network
ONVIF
Open Network Video Interface
Forum
OS
Operating System
PC
Personal Computer
PLA
Polylactic Acid
V
Volt
Introduction
4
Overview
Ward is an edge device powered with intelligent modules and
advanced networking. Its main goal is to effectively maintain
camera surveillance system events. It monitors every assigned
camera.
•Real time event detection
•Instant notification system
Key Features
Package Elements
Check if the following items are included in package. If anything is missing or appears
damaged, contact your dealer immediately.
5
5V 4.5A Adapter* Ethernet Cable
* Adapter head differs from region to region.
Ward
Product Views
6
Bottom View
Top View
7
Front View
Back View
Set up your Ward
8
Ward connects to your home network and allows you to mount your
local IP cameras.
➢To integrate your Ward:
1. Connect your Ward to your router using the Ethernet cable.
2. Connect the AC adapter to your Ward.
Ethernet Jack
Power Jack
Configure your Ward
9
Before configuring your IPCs to your Ward, Device Manager should have
been installed. It can be installed from this link.
➢To configure your cameras:
1. Open Device Manager software.
2. Connect your PC to same network as your Wards.
3. Wait for application to find Wards on the local area network.
10
4. Select the Ward you want to mount to your IPC.
5. Click add button to mount an IPC.
11
6. Enter your IPC credentials and click ADD button.
7. Your IPC is now surveyed by the Ward at the 192.168.137.36!
Troubleshooting
Problem #1: My Ward is not seen in software.
Solutions:
✓Check your internet connection. If your computer is not connected as
same network as your devices, you wouldn’t find your Ward.
✓Restart your Ward by plug-out and plug-in the power cable. Wait for
until green light turns on.
✓Click Find Devices if desired Ward cannot be found.
12
✓Click Try Again if no device was found.
Problem #2: Ward cannot connect to IPC.
13
Solutions:
✓Check your IPC whether it is online.
✓Check the connectivity between desired IPC and Ward. For
further information, look Network Connection section.
14
Safety Precautions
•Only use adapters with 5V 4.5A.
•Do not bang your Ward or subject it to strong impacts.
•Avoid exposure to any kind of liquid.
Placement of the Wards
Avoid placing your Ward subject to:
•strong sunlight.
•temperatures above 40°C (104°F).
•high moisture.
•dust.
Prevent malfunctions
Status Colours
15
Ward evaluates video stream coming from mounted camera.
Device manager uses three different status colours to
demonstrate status of the mounted cameras with respect to
Status/Situation
Camera Connection Critical Event
Normal
✓
Critical
✓ ✓
Unavailable
Event Detection
Ward comes with fire detection module as default. When there is no critical
event, all status buttons look green.
16
When there is a critical event, status of the exact camera and ALL mounted
Wards turns red.
Requirements
PC Requirements
17
•512 MB RAM
•Required OS :
❑Windows 7,8,10
❑OS X 10.9 or higher
IPC Requirements
•ONVIF Support
Specifications
18
Hardware Jetson Nano 4GB
Bottom Case Material PLA
Top Case Material PLA
Disclaimer
•This manual is prepared for giving complete information about
the Ward and Device Manager. However, if you notice that
something is missing, please contact us.
•Reprinting this manual without permission of EyeCU is prohibited.
•Contents of this user manual may have been deprecated without
your information. Thus, please update your manual from EyeCU
website.
•EyeCU accepts no liability damages due to the misusage of the
products.
© Copyright EyeCU 2021®. All documentation rights reserved.
Table of contents
