EZ-Trap EZT-113 User manual

EZ-TRAP WARRANTY
The manufacturer disclaims all implied and express warranties, including the implied
warranty of merchantability and the implied warranty of fitness for a particular
purpose, except as follows:
The EZ-Trap condensate trap or overflow switch purchased by you is unconditionally
warranteed to be free from defects in material and workmanship under normal use for
a period of three (3) years from date of purchase, providing it is installed and operated
strictly in accordance with manufacturer’s installation instructions.
If the product is found to be defective or otherwise fails in normal use, you may return
it for replacement. All freight charges for the return of the product shall be borne by
you. The manufacturer will pay outgoing freight charges for the replacement product.
Defective products returned to EZ-Trap prepaid will be repaired or replaced free of
charge. Replacement product will, to the extent such product is then available in
manufacturer’s inventory, be of similar type, color and kind. Manufacturer retains the
right to substitute product if replacement product does not conform in terms of color,
type and specifications to the original product, if no longer available.
This warranty does not cover replacement labor or any cost, claim or incident to any
defect nor does it cover any consequential damages. The sole liability of the
manufacturer under this warranty is limited to the replacement of defective product.
Product damaged by improper use, accident, neglect, alteration, abuse or improper
installation is excluded from this warranty.
113 INSTALL 7/04
CONTENTS
1 - 3/4Blow Molded EZ-Trap
®
1 - 3/4Tee
1 - 3/4Cross 1 - Yellow Cleaning Label
3 - 3/4Red Caps
3⁄4ECONOMY
CONDENSATE TRAP
Model EZT-113
EZT-113
©2004
EZ-TRAP INC.
3 Kellogg Court, Unit 10 Edison, NJ 08817
phone: [phone] fax: [phone]
e-mail: [e-mail] web: www.eztrap.com
THE TRAP
EXPERTS
U.S. PATENT NUMBERS 5,069,042 5,522,229
62233 0001373
EZT-113

1. Screw adaptor into drain outlet on primary drain pan.
Cut PVC stub to length & glue into adaptor (Figure 1).
2. Glue inlet Cross onto stub. Cross MUST BE PLUMB.
(Figure 2). Open (uncapped) end of cross faces down.
3. Glue long end of U-Bend into bottom of Cross facing
direction required, at least 5° off center (Figure 3).
4. Rotate outlet Tee in required direction and glue onto other end
of U-Bend so that Red Cap faces up (Figure 4).
5. Glue condensate line from center leg of Tee to outside
building (Figure 5).
6. Check for correct operation by pouring water into top
opening of Cross (Figure 6). Horizontal Red Cap must
remain in place during testing.
7. Replace Red Cap on top of inlet Cross and seat firmly
(Figure 7). Red Caps are removable for cleaning and testing
only. All Caps must remain closed during normal operation of
the trap.
8. Place brush in retaining hole on Red Cap.
9. Attach Yellow cleaning label on air handler close to trap.
1. Inserte un adaptador en la salida de drenaje en la bandeja
de drenaje principal. Corte un cabo de PVC de acuerdo a la
longitud y péguelo dentro del adaptador (Figura 1).
2. Pegue la cruz de entrada en el tubo. La cruz DEBE
ESTAR A PLOMO. (Figura 2). Abertura abierto de la cruz
es apuntando abajo.
3. Pegue el extremo largo del doblez en U dentro del fondo
de la cruz apuntando a la dirección debida, mínimo a
5 grados del centro (Figura 3).
4. Gire la T de salida en la dirección debida y péguela en
el otro extremo del doblez en U de tal modo que el tapón
rojo hacia arriba (Figura 4).
5. Pegue la línea de condensado desde la pata central
de la T al edificio exterior (Figura 5).
6. Revise si funciona correctamente vertiendo agua en
la abertura superior de la cruz (Figura 6). El tapón rojo
horizontal debe estar cerido durante la revisionmente.
7. Reemplace el tapón rojo en la parte superior de la cruz de
entrada y asiente firmemente (Figura 7). Los tapones rojos
son removibles únicamente para realizar limpieza y pruebas.
Todos los tapones deben permanecer cerrados durante la
operación normal de la trampa.
8. Coloque el cepillo en el agujero de retención del tapón rojo.
9. Coloque la etiqueta de limpieza amarilla en el manipulador
de aire cerca de la trampa.
IMPORTANT NOTES
1. THIS DEVICE MUST BE INSTALLED STRICTLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS TO ENSURE PROPER
OPERATION AND IN ACCORDANCE WITH ALL APPLICABLE LOCAL PLUMBING AND DRAINAGE CODES.
2. THIS EZ-TRAP
®
IS SUITABLE FOR USE ONLY IN DRAIN PANS WITH 3/4OUTLET. DO NOT USE ON LARGER SIZES AS IT
MAY NOT BE ABLE TO HANDLE THE CONDENSATE PRODUCED BY LARGER TONNAGE UNITS. CONSULT FACTORY FOR
DETAILS ON LARGER TRAPS IF REQUIRED.
NOTAS IMPORTANTES
1. ESTE DISPOSITIVO DEBE INSTALARSE ESTRICTAMENTE DE ACUERDO CON LAS INSTRUCCIONES DEL FABRICANTE PARA
ASEGURAR SU FUNCIONAMIENTO CORRECTO Y SEGÚN TODOS LOS CÓDIGOS LOCALES APLICABLES DE PLOMERÍA Y
DRENAJE.
2. ESTA TRAMPA ES ADECUADA PARA USAR ÚNICAMENTE EN DESAGÜES DE BANDEJA DE DRENAJE DE 3/4.NO LO USE
CON TAMAÑOS MAYORES YA QUE PODRÍA NO ESTAR EN CAPACIDAD DE MANEJAR PRESIONES MÁS ALTAS O FLUJO DE
CONDENSADO DE UNIDADES DE MAYOR TONELAJE. SI LO REQUIERE, CONSULTE A LA FÁBRICA POR DETALLES Y
ESPECIFICACIONES DE TRAMPAS MÁS GRANDES.
INSTALLATION INSTRUCTIONS/ INSTRUCCIONES DE INSTALACIÓN
Model EZT-113
Figure 1
Figure 2
Figure 3
Figure 5
Figure 6 Figure 7
Figure 4
TOP MUST BE LEVEL/
LA PARTE SUPERIOR DEBE ESTAR NIVELADA
CONDENSATE DRAIN LINE
LINEA DE CONDENSADO
SIDE MUST BE
PLUMB/EL LADO DEBE
ESTAR A PLOMO
62233 0001373
EZT-113